• KSTLE International Journal
• /
• 제2권2호
• /
• pp.85-92
• /
• 2001

The variation of contact traction induced by different contact shapes is studied experimentally and theoretically. Considerations fer the contact shape are rounded, truncated and truncated with rounding punches. A fretting wear experiment is conducted with the contact configuration of the strip on the tube specimens. The strip specimen is pressed to form the end profile of a rounded and truncated with rounding punches shape. Wear on the tube is investigated, which is regarded as the slip region of the contact surface. Taken into consideration is the general solution of the normal traction in the case of the indentation by a punch with its end profile of the combination of parabolas. Then, partial slip solution is obtained numerically, which is compared with the wear on the tube. The radius of the rounding and the obliquity of the edge truncation affect the tractions considerably. It is found that the proper choice of the end profile can restrain the contact-induced failure such aswear.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.66-70
• /
• 2001

The purpose of this paper is to investigate the characteristics of springback for the U-bending of steel sheets for automotive body panels. This study presents the experimental and analytical approach for the two kind of steel sheets, namely SCP1 and TRIP(Transformation-induced plasticity), the newly developed high strength steel. The adopted thicknesses are 0.8, 1.2 and 1.6 mm for SCP1, and 1.0 mm for TRIP. The punch profile radii are designed in 3, 6, 9, 12, and 15 mm. As results, the springgo aspect could be observed experimently in the small punch profile radius. The degree of springback for TRIP sheets was more than the SCP1 sheets.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1068-1073
• /
• 2003

Method for contact failure mitigation is studied in this paper. The focus is laid on the contact shape that eventually influences the internal stresses. Contact mechanics is consulted within the frame of plane problem. Hertzian contact, rounded punch and uniform traction profiles are considered. Frictional as well as frictionless contact is also considered. As results, the higher traction profile induced by the rounded punch reveals the greatest among the considered shapes. Therefore, it is suggested to increase the edge radius as large as possible if a contact body of punch shape needs to be designed. It is also found that uniform traction cannot always provide the solution of contact failure mitigation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.75-80
• /
• 2001

The purpose of this study is to investigate the characteristics of springback for various process conditions of the 2D draw-bending operation. The process variables are the forming temperature, the geometry of tools such as punch profile radius(Rp) and die profile radius(Rd). Especially, in order to control the springback, the use of the warm forming method is applied. For the warm draw-bending, five steps of temperature ranges, from room temperature to $200^{\circ}C$, were adopted. And two kinds of steel sheets, namely SCP1 and TRIP(transformation-induced plasticity), the newly developed high strength Steel, were adopted. As a result, the springback was affected by the elevated temperature and the geometry of tools in two kinds of steel sheets.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.48-53
• /
• 2002

Sheet or plate bending is one of the most important industrial metal forming processes. And considerable attention has been focused on gaining a better understanding of many of bending characteristics. One of defaults in bending process is the springback. In this study, the springback characteristics of tailor-welded strips in U-bending process was investigated. Furthermore, not only the relationships between the springback and the process variables such as the geometry of the tools and thickness combination of workpiece but also the heat effect which affects the springback due to welding process was experimentally considered. First, tailor-welded strips are joined by the laser welding process and consisted of two types of thickness combinations of the SCPI sheet, 0.8t${\times}$1.2t and 0.8${\times}$1.6t to investigate the effect of different thickness combination on the springback. Secondly, two different directionally welded strips, one was welded along the centerline of the strip-width and the other was along the centerline of strip-length, were adopted to compare the effects of the location of weld line on the springback. And three punch profile radii of 3, 9, and 15 m were used. Some cases of the experimental results were simulated by using a commercial FEM code, PAM-STAMP to compare the experimental results to the analytical ones.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.87-93
• /
• 2004

An experimental is carried out to investigate the characteristics of blanking for nickel alloy Alloy42 (t=0.203mm), a kind of IC lead frame material. By varying clearance between die and punch the shapes of shear profile are examined. Finite element analysis with element deletion algorithm for ductile fracture mode is also carried out to study the effect of clearance theoretically and to compare with experimental results. The rectangular shape specimen with four different comer radius is used to study the characteristics of blanking for straight side and comer region simultaneously. As the result the ratios measured k(m experiment of roll over, burnish and fracture zone based on initial blank thickness are compared with those of FE analysis. Both experiment and FE analysis show that the amount of mil over and fracture is increased as the clearance increases. When the radius of comer is less than thickness of blank it has been found that larger clearance is required than that of straight region in order to maintain same quality of shear profile at the comer region.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.182-188
• /
• 2001

An experiment is carried out to investigate the characteristics of blanking for copper alloy C194 (t=0.254mm), a kind of IC lead frame material. By varying clearance between die and punch, the shapes of shear profile are examined. Finite element analysis with element deletion algorithm for ductile fracture mode is also carried out to study the effect of clearance theoretically and to compare with experimental results. The rectangular shape specimen with four different corner radius is used to study the characteristics of blanking for straight side and corner region simultaneously. As the result, the ratios measured from the experiment of roll over, burnish, and fracture zone based on intial blank thickness are compared with those of FE analysis. Both experiment and FE analysis show that the amount of roll over and fracture is increased as the clearance increases. It has been found that larger clearance is required than that of straight region when the radius of corner is less than thickness of blank, in order to maintain same quality of shear profile at the corner region.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.389-395
• /
• 2001

To restrain contact failure, present study investigates the influence of edge machining of an indenter (punch). As for the edge machining, rounding, chamfering, and chamfering and rounding are considered. Contact mechanics is consulted to examine the traction profile and the size of the contact region which are directly influenced by the end profile of the indenter. The effect of rounding size (i.e., radius) in the case of the chamfering and rounding edge-indenter is studied. Shear traction is also evaluated within the regime of partial slip. Size of slip region and its expansion rate due to the increase of shear force are considered to investigate the shape effect of the indenter on contact failure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.829-832
• /
• 2000

This paper describes a research work of developing a computer-aided design of product with bending and piercing for progressive working. An approach to the CAD system is based on the knowledge-based rules. Knowledge fur the CAD system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer and is composed of three main modules, which are input and shape treatment, flat pattern layout and strip layout module. Based on knowledge-based rules, the system is designed by considering several factors, such as radius and angle of bend, material and thickness of product, complexities of blank geometry and punch profile, bending sequence, and availability of press. Strip layout drawing automatically generated by piercing with punch profiles divided into for external area is simulated in 3-D graphic forms, including bending sequences for the product with piercing and bending. Results obtained using the modules enable the manufacturer of electronic products to be more efficient in this field.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.198-206
• /
• 2000

This paper describes a research work of developing automated progressive process planning system for working electric products. An approach to the CAD system in based on the knowledge-based rules. Knowledge for the CAD system is formulated from plasticity theories experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer and is composed of three main modules which are input and shape treatment flat pattern layout and strip layout module. Based on knowledge-based rules the system is design by considering several factors such as radius and angle of bend material and thickness of product complexities of blank geometry and punch profile bending sequence and availability of press. Strip layout drawing automatically generated by piercing with punch profiles divided into for external area is simulated in 3-D graphic forms including bending sequences for the product with piercing and bending. Results obtained using the modules enable the manufacture of electronic products to be more efficient in this field.