• 수산해양기술연구
• /
• 제34권2호
• /
• pp.212-222
• /
• 1998

Heat transfer performance improvement by fin and groovs is studied for condensation of R-11 on integral-fin tubes. Eight tubes with trapczodially shaped integral-fins having fin density from 748 to 1654fpm(fin per meter) and 10, 30 grooves are tested. A plain tube having the same diameter as the finned tubes is also used for comparison. R-11 condensates at saturation state of 32 $^{\circ}C$ on the outside tube surface coded by inside water flow. All of test data are taken at steady state. The heat transfer loop is used for testing singe long tubes and cooling is pumped from a storage tank through filters and folwmeters to the horizontal test section where it is heated by steam condensing on the outside of the tubes. The pressure drop across the test section is measured by menas pressure gauge and manometer. The results obtained in this study is as follows : 1. Based on inside diameter and nominal inside area, overall heat transfer coefficients of finned tube are enhanced up to 1.6 ~ 3.7 times that of a plain tube at a constant Reynolds number. 2. Friction factors are up to 1.6 ~ 2.1 times those of plain tubes. 3. The constant pumping power ratio for the low integral-fin tubes increase directly with the effective area to the nominal area ratio, and with the effective area diameter ratio. 4. A tube having a fin density of 1299fpm and 30 grooves has the best heat transfer performance.

• 한국항공우주학회지
• /
• 제34권9호
• /
• pp.89-96
• /
• 2006

본 연구에서는 소형 위성용 하이브리드 로켓 점화장치에 적용되는 N2O 촉매 베드의 유동 및 열적 현상에 대한 이론적인 고찰을 하였다. 허니콤 형상을 가지는 촉매 베드 내의 열적 현상을 분석하기 위해서 다공성 매질 접근법을 사용하였다. 유동장은 Brinkman- extended Darcy 모델을 사용하였고, 온도장은 One-equation 모델을 사용하여 촉매 베드 내에서 유동장 및 온도장에 대한 해석해들을 구하였다. 다공성 매질 접근법을 적용한 모델의 해석해와 기존 실험결과를 비교하여 본 모델의 정확성을 검증하였다. 해석해에 근거하여 N2O 촉매 베드에 영향을 미치는 중요한 변수들이 촉매 베드의 기공률, 유효 체적비, 촉매 베드와 기공의 직경비, 공급열, 그리고 펌핑파워임을 확인하였으며 촉매 베드 내에서의 열적현상에 대한 중요 변수들의 효과를 연구하였다.

• 한국태양에너지학회 논문집
• /
• 제35권4호
• /
• pp.43-55
• /
• 2015

This paper presents the thermal hydraulic performance of a three dimensional rib-roughened solar air heater (SAH) duct with the one principal wall subjected to uniform heat flux. The SAH duct has aspect ratio of 12.0 and the Reynolds number ranges from 2000 to 12000. The roughness has relative rib height of 0.045, ratio of dimple depth to print diameter of 0.5 and rib pitch ratio of 8.0. The flow attack angle is varied from $35^{\circ}$ to $70^{\circ}$. Various turbulent flow models are used for the heat transfer and fluid flow analysis and their results are compared with the experimental results for smooth surfaces. The computational fluid dynamics (CFD) results based on the renormalization k-epsilon model are in better outcomes compared with the experimental data. This model is used to calculate heat transfer and fluid flow in SAH duct with the compound roughness of V-shaped ribs and dimples. The overall thermal performance based on equal pumping power is found to be the highest (2.18) for flow attack angle of $55^{\circ}$. The thermo-hydraulic performance for V-pattern shaped ribs combined with dimple ribs is higher than that for dimple rib shape and V-pattern rib shape air duct.

• 한국유체기계학회 논문집
• /
• 제20권1호
• /
• pp.74-80
• /
• 2017

Pump sump system or pumping stations are built to draw water from a source such as river and used for irrigation, thermal power plants etc. If pump sump is improperly shaped or sized, air entraining vortices or submerged vortices may develop. This may greatly affect pump operation if vortices grow to an appreciable extent. Moreover, the noise and vibration of the pump can be increased by the remaining of vortices in the pump flow passage. Therefore, the vortices in the pump flow passage have to be reduced for a good performance of pump sump station. In this study, the effect of pump intake leaning angle and flow rate on the pump sump internal flow has been investigated. There are three cases with different leaning angle. Moreover, a pipe type with elbow also has been studied. The flow rate with three classes of air entraining vortices has been examined and investigated by decreasing the water level. The result shows that the air entraining vortices easily occurs at the pump intake with large leaning angle. Moreover, the elbow type of the pump intake easily occurs air entraining vortices at the high flow rate (or velocity) in comparison to other pump intake type.

• 한국초전도ㆍ저온공학회논문지
• /
• 제13권4호
• /
• pp.30-35
• /
• 2011

This paper describes experimental study and performance improvement of 2 stage Gifford-McMahon (G-M) type pulse tube cryocooler for cryopump. The objective of this study is to improve the efficiency of 2 stage pulse tube cryocooler for substituting 2 stage G-M cryocooler used in cryopump. The target cooling capacities are 5 W at 20 K and 35 W at 80 K for the $1^{st}$ and the $2^{nd}$ stage, respectively. These values are good cooling capacities for vacuum level in medium size ICP 200 cryopump. Design of the 2 stage pulse tube cryocooler is conducted by FZKPTR(Forschungs Zentrum Karlsruhe Pulse Tube Refrigerator) program. In order to improve the performance of 2 stage pulse tube cryocooler, U-type pulse tube cryocooler is fabricated and connecting tubes are minimized for reducing dead volumes and pressure losses. Also, to get larger capacities, orifice valves and double inlet valves are optimized and the compressor of 6 kW is used. On the latest unit, the lowest temperatures of 2 stage pulse tube cryocooler are 42 K ($1^{st}$ stage) and 8.3 K ($2^{nd}$ stage) and the cooling capacities are 40 W at 82.9 K ($1^{st}$ stage) and 10 W at 20.5 K ($2^{nd}$ stage) with 6.0 kW of compressor input power. This pulse tube cryocooler is suited for commercial medium size cryopump. In performance test of cryopump with 2 stage pulse tube cryocooler, pumping speed for gaseous nitrogen is 4,300 L/s and the ultimate vacuum pressure is $7.5{\times}10^{-10}$ mbar.

• 설비공학논문집
• /
• 제23권12호
• /
• pp.791-798
• /
• 2011

In this study, performance of R410A(50%R32/50%R125) and HFC32/HFC125 mixture is measured to examine the effect of composition shift of R410A used for various air-conditioners and heat pumps. The composition of HFC32/HFC125 mixture varies from the reference composition of R410A ${\pm}10%$ with 5% interval. Tests carried out in a heat pump bench tester at the evaporation and condensation temperatures of $7/45^{\circ}C$ and $-7/41^{\circ}C$ for summer and winter conditions, respectively. Test results show that both the coefficient of performance (COP) and compressor power of the HFC32/HFC125 mixture have the maximum difference of 2.0% as compared to those of R410A. Compressor discharge temperatures of HFC32/HFC125 mixture are increased up to $6.7^{\circ}C$ as compared to that of R410A. The amount of charge for HFC32/HFC125 mixture vary within 5.6% as compared to that of R410A. Overall, performance of R410A is not appreciably affected by the composition shift of ${\pm}10%$ of R32 under both air-conditioning and heat pumping conditions.

• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.789-799
• /
• 2004

An experimental study is conducted to investigate the effects of duct corrugation angle on heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger application. Local heat/mass transfer coefficients on the wavy duct sidewalls are determined by using a naphthalene sublimation technique. The corrugation angles(${\alpha}$) of the wavy ducts are 145$^{\circ}$, 130$^{\circ}$, 115$^{\circ}$ and 100$^{\circ}$. And the Reynolds numbers based on the duct hydraulic diameter vary from 300 to 3,000. The results show that at the low Re(Re $\leq$1000), the secondary vortices called Taylor-Gortler vortices perpendicular to the main flow direction are generated due to effect of duct curvature. By these secondary vortices, high heat/mass transfer regions are formed on both pressure-side and suction-side walls. At the high Re(Re $\geq$ 1000), these secondary flows are vanished with helping flow transition to turbulent flow and the regions which show high heat/mass coefficients by flow reattachment are formed on suction side. As corrugation angle decreases, the local peak Sh induced by Taylor-Gortler vortices increase at Re $\leq$1000. At high Re(Re $\geq$ 1000), by the existence of different kind of secondary flows called Dean vortices, non-uniform Sh distribution appears along spanwise direction at the narrow corrugation angle (${\alpha}$=100$^{\circ}$). Average Sh also increase by the enhanced effect of secondary vortices and flow reattachment. More pumping power (pressure loss) is required with the smaller corrugation angle due to the enhancement of flow instability.

• 설비공학논문집
• /
• 제17권6호
• /
• pp.569-580
• /
• 2005

The present study investigates the convective heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger. The effects of duct aspect ratio and flow velocity on the heat/mass transfer are investigated. Local heat/mass transfer coefficients on the corrugated duct sidewall are determined using a naphthalene sublimation technique. The aspect ratios of the wavy duct are 7.3, 4.7 and 1.8 with the corrugation angle of $145\Omega$. The Reynolds numbers, based on the duct hydraulic diameter, vary from 300 to 3,000. The results show that at the low Re(Re $\leq$ 1000) the secondary vortices called Taylor-Gortler vortices perpendicular to the main flow direction are generated due to effect of duct curvature. By these secondary vortices, non-uniform heat/mass transfer coefficients distributions appear. As the aspect ratio decreases, the number of cells formed by secondary vortices are reduced and secondary vortices and comer vortices mix due to decreased aspect ratio at Re$\leq$1000. At Re >1000, the effects of corner vortices become stronger. The average Sh for the aspect ratio of 7.3 and 4.7 are almost same. But at the small aspect ratio of 1.8, the average Sh decreases due to decreased aspect ratio. More pumping power (pressure loss) is required for the larger aspect ratio due to the higher flow instability.

• 대한토목학회논문집
• /
• 제39권4호
• /
• pp.477-483
• /
• 2019

최근 원자력발전소 및 LNG 저장탱크 등 특수구조물의 공사 기간과 비용 절감을 목적으로 PSC 구조물 대신 프리캐스트 형식의 SCP 모듈의 사용이 증가하고 있다. SCP 모듈 내부는 강재와 콘크리트의 일체 거동을 위해 스터드로 연결되어 있어 고유동 콘크리트의 사용이 요구된다. 고유동 콘크리트는 일반적으로 많은 단위결합재량를 가지기 때문에 수화열 및 수축의 증대, 비경제적인 강도 발현 문제 등이 발생한다. 따라서 본 연구에서는 저분체 기반 고유동 콘크리트 최적 배합을 선정하기 위해 재료적 특성에 따른 고유동 콘크리트의 유동성 및 철근의 간극 통과성능을 검토하고, 펌프카를 활용하여 펌핑 전후에 따른 콘크리트의 물성을 검토하며, 최종적으로 강재와 강재 사이를 콘크리트로 채우는 SCP Mock-up 부재에 대하여 고유동 콘크리트의 충전 성능을 평가하였다.

• 한국지반환경공학회 논문집
• /
• 제12권7호
• /
• pp.13-21
• /
• 2011

동절기와 해빙기의 기온차가 큰 지역에서는 일정 깊이까지 동결, 융해 작용이 반복적으로 발생하여 흙의 역학적 특성이 변화를 보이게 된다. 특히 세립분이 많은 흙인 경우 팽창과 수축을 통한 입자의 재배열 등으로 인하여 노반의 연약화가 많이 발생된다. 이러한 노반의 연약화는 지지력이 낮은 지반에서 반복하중이 재하 되었을 때 급격하게 나타날 수 있다. 본 연구에서는 국내의 철도 노반재료로 사용되는 대표 토질 3가지를 대상으로 세립분의 함유량, 간극비의 영향 등을 고려하여 동결융해 반복횟수에 따른 직접전단 시험을 실시하여 그 감소량을 정량적으로 평가하였으며, 이를 통하여 세립분의 함유량과 함수비 조건, 동결융해 횟수 등을 고려할 수 있는 전단강도 저감 모델 식을 제안하였다.