• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.403-408
• /
• 2007

According as diesel automobile are produced, reduce noise and vibration that is occurred by characteristic of diesel engine, and need engine room layout optimization and research for light weight of parts. Balance Shaft Module is module parts for vehicles engine to improve performance and efficiency of engine and reduce noise and vibration. These days, an oil pump integrated balance shaft module and an oil sump integrated balance shaft module is on the rising for optimizing of engine room. In this study, produced prototype of oil pump integrated type balance shaft module, and achieved dynamic characteristic test about experimental modal analysis and noise/vibration of balance shaft module.

• 한국생산제조학회지
• /
• 제26권4호
• /
• pp.387-394
• /
• 2017

This paper develops a pump system for patient with chronic pain or cancer. The pump module is consists of two micro-valve and membrane. The micro-valve is operated by a solenoid. With two solenoid valves which are connected via a drug transport line, the inlet and outlet are completely blocked. A silicon rubber membrane located between the two valves makes the flow-rate constant without any backflow. This pump module can control the flow-rate of drugs by controlling the time that the valves are opened and closed. The reservoir consists of a drug chamber and a gas chamber. As the gas chamber encloses the drug chamber, propellant gas which is injected into the gas chamber pressurizes the drug chamber regardless of volume of the drug chamber. To design the pump module, analysis a constant efficiency test, and accuracy test for the pump module were conducted.

• 한국유체기계학회 논문집
• /
• 제12권3호
• /
• pp.31-37
• /
• 2009

This paper presents a implantable intrathecal drug infusion pump for pain control in cancer patients. This device consists of micropump module, drug reservoir module and control module. The micropump module using cam-follower mechanism composed of small-sized four cams and four followers. Each followers is driven by a cam and liquid is discharged by a sequential reciprocal motion of the followers. The advantage of this structure is that it allows the pump to be clean and valveless. The drug reservoir module composed of drug chamber, gas chamber and diaphragm. The control module composed of battery, wireless communication unit and controller. To design a small-sized, low power pump some analysis were performed to determine the design parameters. To verify the feasibility of the experiment, a prototype was manufactured and its operating characteristics were investigated. Experimental results were in accordance with the expected results obtained from analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.137-140
• /
• 2005

The electronic dispenser is composed of electronic part and mechanical part. Electronic part is consisted of input keypad, micro-controller, display module, and pump module. In this paper we designed micro-controller for electronic part. The micro-controller controls display module and pump module. The display module is composed by LCD device, and the pump module is composed by motor device. The micro-controller for an electronic dispenser is designed by VHDL. We used WX12864APl for the LCD device and SPS20 for the stepping motor. Also, the micro-controller is designed by Altera Quartus tool and verified with Agent 2000 Design-kit using APEX20K Device. In this paper, we present possibility to adopt of biotechnology field through designing of one-chip controller for an electronic dispenser.

• 한국공작기계학회논문집
• /
• 제11권1호
• /
• pp.91-96
• /
• 2002

Recently industry has moved towards automated operations with the goal of achieving better product quality greater productivity and reliability The pump design in characterized by extensive utilization of the related database which contains performance data. The inputs to the system are through interactive dialogue sessions and the basic input consist of flow rate, head, of fluid efficiency and the customer special requirements. These basic inputs along with the numerous rules in the knowledge bases and the mathematical modeling enable the effective design of the pump industry This paper represents the development of an automatic pump design system that was composed of a main program the data input module the drawing module the drawing edit module and was programed by the AutoLISP language under the Auto CAD program The developed system ultimately generates the design for a pump through the AutoCAD language.

• 전력전자학회논문지
• /
• 제13권2호
• /
• pp.135-144
• /
• 2008

일반적으로 Intelligent power module (IPM)의 상부 스위치 구동을 위한 플로팅 전원 공급 방법으로 부트스트랩 회로가 많이 사용되고 있다. 부트스트랩 회로는 구성이 간단하고 집적화가 가능하다는 장점이 있으나 몇 가지 문제점을 가지고 있다. 상부 스위치 게이트 드라이버 회로에 전원을 공급하기 위해 매 주기마다 충분한 에너지를 충전할 수 있는 시간이 요구되며, 충전된 에너지는 한정적이므로 스위치 턴 온 (turn-on)시간의 제한을 갖게 된다. 그리고 주파수가 낮아질수록 부트스트랩 커패시터 용량이 증가하여 집적화에 장애요인이 된다. 이러한 단점은 전하 펌프 회로를 사용함으로써 보완될 수 있다. 본 논문에서는 IPM의 플로팅 전원 공급 방법으로 전하 펌프 회로를 적용하여 분석하였으며, 이러한 분석을 기반으로 전하 펌프 회로의 설계 방법을 제안하였다. 분석과 제안된 설계 방법의 타당성을 검증하기 위하여 시뮬레이션과 실험을 수행하였으며, 제시된 결과는 제안된 설계 방법의 유용성을 입증하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.477-480
• /
• 2007

Inlet fluid temperature of the BRE in the geothermal heat pump system depends on heat exchange rate between the refrigerant of the heat pump and the leaving fluid from the BRE. Because the outlet fluid temperature of the BHE varies with time, inlet fluid temperature has to vary with time. In this study, the module to calculate inlet fluid temperature is developed, which can consider the time-varying outlet fluid temperature and the heat exchange capacity of the heat pump. It is assumed that heat loss or gain of the leaving fluid from outlet to inlet of the BHE is negligible, except when the fluid contacts with the refrigerant of the heat pump. This module is combined with TOUGHREACT, a widely accepted three-dimensional numerical simulator for heat and water flow and geochemical reactions in geothermal systems and is applied to data analyses of the thermal response test.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.319-324
• /
• 2005

The interface between host processor and the ShortStack Micro Server may be a Serial Communication Interface(SCI). The LonWorks control module with a high performance is developed, which is composed of the 8 bit PIC Microprocessor for host processor and the smart neuron chip for the ShoretStack Micro Server. This intelligent control board is verified as proceeding the various function tests from experimental system with an boost pump and inverter driving systems. It is also confirmed that the developed control module provides stably 0-10VDC linear signal to the input signal of inverter driving system for varying the induction motor speed. Thus, the experimental results show that the fabricating intelligent board carried out very well the various functions in the wide operating ranges of boost pump system. This developed control module expect to apply to industrial fields to require the comparatively exact control and monitoring such as multi-motor driving system with inverter, variable air volume system and the boost pump water supply systems.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.153-160
• /
• 2020

In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO₂ cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO₂ as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO₂ cycle test loop. The pressurized CO₂, at a temperature of 136℃, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 ㎛.

• 전기전자학회논문지
• /
• 제9권2호
• /
• pp.101-107
• /
• 2005

본 논문에서는 전자 디스펜서(dispenser)용 제어기를 단일 칩으로 설계하였다. 전자 디스펜서는 전자부분과 기계부분으로 구성되며, 전자부분은 이력 키패드, 제어기, 디스플레이 모듈과 펌프모듈로 구성된다. 본 논문에서 설계한 제어기는 LCD 소자와 모터 펌프를 제어하며 VHDL을 이용하여 설계하였다. LCD 소자로서 WX12864AP1을 사용하였으며, 스테핑 모터로는 SPS20을 사용하였다. 이 제어기는 Altera사의 Quartus 툴을 사용하여 설계 후, Agent 2000 설계 키트와 APEX20K 소자를 사용하여 LCD 모듈과 모터모듈에 연결하여 동작 검증함으로, 동작이 원활히 이루어짐을 확인하였다. 본 논문에서는 전자 디스펜서의 제어기 설계를 통해 전자 디스펜서의 전용 칩을 ASIC으로 구현하여 바이오기술 분야의 기기에 적용할 수 있는 가능성을 제시하였다.