• 한국군사과학기술학회지
• /
• 제17권1호
• /
• pp.90-95
• /
• 2014

The system design and the system performance analysis of 3D imaging laser radar system for the mapping purpose is addressed in this article. For the mapping, a push-bloom scanning method is utilized. The pulsed fiber laser with high pulse energy and high pulse repetition rate is used for the light source of laser radar system. The high sensitive linear mode InGaAs avalanche photo-diode is used for the laser receiver module. The time-of-flight of laser pulse from the laser to the receiver is calculated by using high speed FPGA based signal processing board. To reduce the walk error of laser pulse regardless of the intensity differences between pulses, the time of flight is measured from peak to peak of laser pulses. To get 3D image with a single pixel detector, Risley scanner which stirs the laser beam in an ellipsoidal pattern is used. The system laser energy budget characteristics is modeled using LADAR equation, from which the system performances such as the pulse detection probability, false alarm and etc. are analyzed and predicted. The test results of the system performances are acquired and compared with the predicted system performance. According to test results, all the system requirements are satisfied. The 3D image which was acquired by using the laser radar system is also presented in this article.

• Journal of Periodontal and Implant Science
• /
• 제26권4호
• /
• pp.989-1002
• /
• 1996

The purpose of this study was to determine the effect of a pulsed Nd:YAG laser irradiation on human gingival tissues. The patients, who were planned to be treated by clinical crown lengthening procedure and gingivectomy, were selected. All the patients received oral hygiene instruction, scaling and root planing at preoperation. The crest of gingival tissue on upper and lower anterior teeth was irradiated by a pulsed Nd:YAG laser(El. EN. EN060, Italy) with a fiber optic of 300 m in contact mode for 20 seconds. Gingival tissues were divided into 4 groups according to the laser power of 1.0W(10Hz, 100mJ), 2.0W(20Hz, 100mJ), 3.0W(30Hz, 100mJ) and 4.0W(40Hz, 100mJ). Immediately after the laser irradiation, the specimens were excised, fixed 10% neutral formalin, sectioned $4-6{\mu}m$ thick, stained by Hematoxylin-Eosin and Periodic Acid Schiff stain and observed under light microscope. The removed tissue depth and the coagulated layer depth due to a laser irradiation by a laser irradiation were measured on the microphotographs. The difference of measurements according to the different laser power was statistical1y analyzed by Kruskal Wallis Test with SAS program. The results were as follows : 1. In histologic findings of irradiated gingival tissues; a. In the irradiated gingival specimen with 1.0W laser power, some vesicles were observed in limited superficial layer of gingival epithelium. b. In the irradiated gingival specimen with 2.0W and 3.0W laser power, the epithelium was almost removed except for the traces of viable basal cell remnants at ret peg, and coagulation necrosis related with the thermal effect of laser was noted. c. In the irradiated gingival specimen with 4.0W laser power, complete removal of epithelium, partial removal of underlying connective tissue, and the coagulation necrosis of subjacent gingival tissue were shown. 2. The removed tissue depth was deeper in the irradiated specimens with higher power. There was a statistical significance in the difference of removed tissue depth between 1.0W group ($44.54{\pm}6.99um$) and 3.0W group ($99.75{\pm}6.64{\mu}m$), and between 1.0W group($44.54{\pm}6.99{\mu}m$) and 4.0W group($111.36{\pm}4.50{\mu}m$), and between 2.0W group($98.01{\pm}4.53{\mu}m$) and 4.0W group($111.36{\pm}4.50{\mu}m$)(P<0.05). 3. The coagulated layer depth was deeper in the irradiated specimens with higher power. There was a statistical significance in the difference of coagulated layer depth between 1.0W group($31.82{\pm}8.99{\mu}m$) and 3.0W group($55.99{\pm}20.94{\mu}m$), and between 1.0W group($31.82{\pm}8.99{\mu}m$) and 4.0W group($83.68{\pm}10.34{\mu}m$)(P<0.05). From this study, the results demonstrated that the effects of a pulsed Nd:YAG laser irradiation on gingival tissues seemed to depend on the laser power and that the irradiation with high power could be harmful to adjacent healthy tissue.

• 한국정밀공학회지
• /
• 제27권10호
• /
• pp.7-13
• /
• 2010

We report a hybrid DPSSL with a pulse parameter variable LD seed, all-fiberized polarization-maintained pulsed Yb-doped fiber preamplifier chains, and a bulk Nd:$YVO_4$ power amplifier. Pulse parameter of LD seed was controlled by direct current modulation. The hybrid DPSSL generates 1064 nm laser pulses with an average power of 40W, a pulse duration of 20-40ns, and a repetition rate of 100-500kHz.

• Journal of Periodontal and Implant Science
• /
• 제26권2호
• /
• pp.511-521
• /
• 1996

Periodontal pocket is one of the most frequently developed clinical feature on the teeth with periodontal disease. In order to determine the gingival curettage effect of intrapocket irradiation of a pulsed Nd : YAG laser on periodontally involved teeth, bilateral 60 teeth with $4{\sim}6mm$ in probing pocket depth 1 week after supragingival scaling were selected. On half of them the intrapocket irradiation($300{\mu}m$ fiber optic, 1.5W power, for 2min.) of a pulsed-Nd : YAG laser(EL.EN.EN06O, Italy) was applied as the lased group. On the contralateral 30 teeth the subgingival curettage was accomplished by Gracey curettes as the curattage group. The periodontal pocket tissues were surgically excised by the modified Widman flap technique immediately after the intrapocket irradiation or subgingival curettage, subsequently fixed with 10% neutral formalin, sectioned in $4{\sim}6{\mu}m$ thickness, and stained with hematoxylin-eosin. Surface characteristics and incomplete removal of the pocket epithelium were evaluated under light microscope. And the difference between the lased group and the curettage group was statistically analyzed by Chi-square test in Microstat program. The results were as follows ; 1. The plane surface was observed more frequently in the curettage group(73.3%) than in the lased group(23.3%), and the rough surface was observed more frequently in the lased grOoup(63.3%) than in the curettage group(6.7%)(p<0.05). 2. The rate of incomplete removal of the pocket epithelium was relatively high in both the lased group(76.6%) and the curettage group(86.6%), and there was no significant difference between the lased group and the curettage group(p>0.l). The results suggest that the further studies including various power control of laser should be succeeded in order to obtain more favorable results by the intrapocket irradiation of a pulsed Nd:YAG laser than the subgingival curettage with Gracey curettes.

• Journal of Periodontal and Implant Science
• /
• 제52권1호
• /
• pp.77-87
• /
• 2022

Purpose: This pilot study assessed the immediate in vivo effect of high peak pulse power neodymium-doped yttrium aluminum garnet (Nd:YAG) laser monotherapy on selected red/orange complex periodontal pathogens in deep human periodontal pockets. Methods: Twelve adults with severe periodontitis were treated with the Laser-Assisted New Attachment Procedure (LANAP®) surgical protocol, wherein a free-running, digitally pulsed, Nd:YAG dental laser was used as the initial therapeutic step before mechanical root debridement. Using a flexible optical fiber in a handpiece, Nd:YAG laser energy, at a density of 196 J/cm² and a high peak pulse power of 1,333 W/pulse, was directed parallel to untreated tooth root surfaces in sequential coronal-apical passes to clinical periodontal probing depths, for a total applied energy dose of approximately 8-12 joules per millimeter of periodontal probing depth at each periodontal site. Subgingival biofilm specimens were collected from each patient before and immediately after Nd:YAG laser monotherapy from periodontal pockets exhibiting ≥6 mm probing depths and bleeding on probing. Selected red/orange complex periodontal pathogens (Porphyromonas gingivalis, Tannerella forsythia, Prevotella intermedia/nigrescens, Fusobacterium nucleatum, Parvimonas micra, and Campylobacter species) were quantified in the subgingival samples using established anaerobic culture techniques. Results: All immediate post-treatment subgingival biofilm specimens continued to yield microbial growth after Nd:YAG laser monotherapy. The mean levels of total cultivable red/orange complex periodontal pathogens per patient significantly decreased from 12.0% pretreatment to 4.9% (a 59.2% decrease) immediately after Nd:YAG laser monotherapy, with 3 (25%) patients rendered culture-negative for all evaluated red/orange complex periodontal pathogens. Conclusions: High peak pulse power Nd:YAG laser monotherapy, used as the initial step in the LANAP® surgical protocol on mature subgingival biofilms, immediately induced significant reductions of nearly 60% in the mean total cultivable red/orange complex periodontal pathogen proportions per patient prior to mechanical root instrumentation and the rest of the LANAP® surgical protocol.

• 한국광학회지
• /
• 제6권4호
• /
• pp.274-281
• /
• 1995

본 논문에서는 가상적인 물체를 기록하고 재생하는 새로운 홀로그램 기록방법인 scanned-object holography를 제안하였으며 그 가능성을 이론과 실험을 통해 증명하였다. 이 방법에서는 점광원으로부터 방출되는 구면파의 이동결과와 정지된 기준파를 연속적으로 간섭시킴으로서 점광원의 이동 경로로 표현되는 가상적인 물체를 기록할 수 있었다. 이때 점광원을 실험적으로 구현하기 위해 광섬유 출력단과 펄스형 레이저를 사용하였다.

• 한국진공학회지
• /
• 제16권5호
• /
• pp.371-376
• /
• 2007

분자선 에피택시(molecular beam epitaxy, MBE)로 성장된 InGaAs 양자점 레이저 다이오드(quantum dot laser diode, QD-LD)와 InGaAs 양자우물 레이저 다이오드(quantum well laser diode, QW-LD)의 특성을 비교하였다. 펄스 입력전류 하에서 문턱전류밀도(threshold current density, $J_{th}$), 특성온도(characteristic temperature, $T_0$), 온도에 따른 발진파장의 변화도($d{\lambda}/dT$)를 측정한 결과, 양자우물 레이저 다이오드는 $J_{th}\;=\;322\;A/cm^2,\;T_0\;=\;55.2\;K,\;d{\lambda}/dT\;=\;0.41\;nm/^{\circ}C$로 측정되었으며, 양자점 레이저 다이오드는 $J_{th}\;=\;116\;A/cm^2,\;T_0\;=\;81.8\;K,\;d{\lambda}/dT\;=\;0.33\;nm/^{\circ}C$로 측정되었다. 양자점 레이저 다이오드는 양자우물 레이저 다이오드와 비교하였을 때, 문턱전류밀도 및 발진 광 파워가 상대적으로 우수한 결과를 보여주었다.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1627-1627
• /
• 2001

In this study, a newly constructed optical measurement system, whose main components were a parametric tunable laser and a near infrared photoelectric multiplier, was applied to detection of the information for the inside of Satsuma mandarin using time-of-flight near infrared spectroscopy (TOF-NIRS). The combined effects on the time resolved profile of sample diameter, sugar content, the wavelength of the laser beam, and the detection position of transmitted light were investigated in detail. The samples used were Satsuma mandarin (Citrus unshu $M^{ARC}$.) (location: Wakayama, Japan) having the diameters of 50-84 mm. The sugar content measured by a refractometer varied from 9.9 to 16.3 Brix%. Equator of sample was irradiated vertically with the pulsed laser, and transmitted output power was measured on the restricted position of the equator using the optical fiber cable. The sampling time and the number of averaging the output power were 100 ns and 100 times, respectively. The variation of the attenuance of peak maxima At, the time delay of peak maxima t and the variation of full width at half maximum w were strongly dependent on the detection position and the wavelength of the laser beam. At, t and w increased gradually as the sample diameter increased to be much absorbed and vigorously scattered. On the other hand, each optical parameter had a tendency to increase as the sugar content increased. Such behavior was remarkable when the transmitted light was detected at the side face of a sample. When we apply TOF-NIRS to detection of the information for the inside of fruit with high moisture content like Satsuma mandarin, it is very important to give attention to the difference in the scattered light within tissues and the semi-straightly propagated light. Furthermore, we tried to express the resulting phenomena by using a model samples composed of water, sucrose, and milk. The variation of the time resolved profile is strongly governed by the combination of the light absorption component, scattering medium, and refractive index.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1626-1626
• /
• 2001

In this study, a newly constructed optical measurement system, whose main components were a parametric tunable laser and a near infrared photoelectric multiplier, was applied to detection of the information for the inside of Satsuma mandarin using time-of-flight near infrared spectroscopy (TOF-NIRS). The combined effects on the time resolved profile of sample diameter, sugar content, the wavelength of the laser beam, and the detection position of transmitted light were investigated in detail. The samples used were Satsuma mandarin (Citrus unshu $M_{ARC}$.) (location: Wakayama, Japan) having the diameters of 50-84 mm. The sugar content measured by a refractometer varied from 9.9 to 16.3 Brix%. Equator of sample was irradiated vertically with the pulsed laser, and transmitted output power was measured on the restricted position of the equator using the optical fiber cable. The sampling time and the number of averaging the output power were 100 ns and 100 times, respectively. The variation of the attenuance of peak maxima At, the time delay of peak maxima $\Delta$t and the variation of full width at half maximum Δw were strongly dependent on the detection position and the wavelength of the laser beam. At, $\Delta$t and $\Delta$w increased gradually as the sample diameter increased to be much absorbed and vigorously scattered. On the other hand, each optical parameter had a tendency to increase as the sugar content increased. Such behavior was remarkable when the transmitted light was detected at the side face of a sample. When we apply TOF-NIRS to detection of the information for the inside of fruit with high moisture content like Satsuma mandarin, it is very important to give attention to the difference in the scattered light within tissues and the semi-straightly propagated light. Furthermore, we tried to express the resulting phenomena by using a model samples composed of water, sucrose, and milk. The variation of the time resolved profile is strongly governed by the combination of the light absorption component, scattering medium, and refractive index.

• 한국전자파학회논문지
• /
• 제23권6호
• /
• pp.706-715
• /
• 2012

전자-광학 시그마-델타 변조기는 안테나로부터 수신된 광대역 초고주파 신호를 직접 디지털 신호로 변환하는 디지털 수신기의 핵심 구성품이다. 전자-광학 시그마-델타 변조기는 펄스 레이저와 두 개의 마하-젠더 간섭계(Mach-Zehnder Interferometer: MZI)를 통하여 입력 신호를 초과 샘플링하고, 격자 섬유 누적기(Fiber-Lattice Accumulator: FLA)를 통하여 잡음을 감소시킨다. 고해상도의 출력 신호를 얻기 위해 양자화기 출력에는 데시메이션 필터링 과정이 추가된다. 변조기 설계시 지터는 변조기 입력 신호를 원 신호로 복원하는데 큰 영향을 미치는 요소이다. 본 논문에서는 전자-광학 1차 단일 비트 시그마-델타 변조기의 구현 과정 및 성능을 시뮬레이션을 통하여 분석한다. 전자-광학 시그마-델타 변조기 입력 신호와 출력 신호를 시간 영역에서 분석하고, 복원된 신호에 대하여 비동기 스펙트럼 평균화 방식을 사용하여 주파수 영역의 성능을 분석한다. 지터(Jitter)가 있는 레이저 신호와 지터가 없는 레이저 신호에 대하여 시그마-델타 변조기의 성능을 비교 및 분석하여, 시간 지터가 변조기 성능에 영향을 미치는 지터값을 참고치(펄스 반복 주파수가 100 GHz인 경우, 시간 지터는 100 fs 이하)로서 제시한다. 이러한 지터값은 레이저 생성기 제작시나 변조기 설계시 참고 규격치로 이용된다.