• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.82-85
• /
• 2000

We introduce pulsed $CO_2$ laser power supply excited by half-wave rectified 60Hz AC discharge some advantage of cost and size compared to a typical pulsed power supply. AC frequency is adjusted from 10Hz to 60Hz to control laser output. In this laser, a low voltage open loop control for high voltage AC discharge circuits is employed to avoid the HV sampling or switching. The control is achieved by using a ZCS circuit and a PIC one-chip microprocessor that control the gate signal of SCR precisely. The pulse repetition rate is limited by 60Hz due to a high leakage inductance. The maximum laser output was obtained about 20W at the condition of total pressure, 18Torr and pulse repetition rate,60Hz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2192-2194
• /
• 1999

In this study, We have accomplished a new approach to develope a cheap and compact pulsed $CO_2$ laser system. We used a fast SCR as switching device instead of a thyatron in the pulsed power supply. Using the Pulse transformer, energy in the condenser is tranferred to the secondary, electrodes of discharge tube, from the primary. An axial and water cooled type was adopted as the laser cavity. The laser performance characteristics as various parameters, such as gas pressure and pulse repetition rate, have been investigated. As a result, the maxium laser output was 12.3[W] at a pulse repetition rate of 120[pps] and a filling pressure of 12[Torr].

• 한국초전도ㆍ저온공학회논문지
• /
• 제23권3호
• /
• pp.41-44
• /
• 2021

We developed an optimization process of the pulsed laser deposition method to grow epitaxial CeCoIn₅ thin films on MgF₂ substrates. The effects of different deposition parameters on film growth were extensively studied by analyzing the measured X-ray diffraction patterns. All the deposited films contained small amounts of CeIn₃ impurity phase and misoriented CeCoIn₅, for which the c-axis of the unit cell is perpendicular to the normal vector of the substrate surface. The deposition temperature, target composition, laser energy density, and repetition rate were found effective in the formation of (00l)-oriented CeCoIn₅ as well as the undesired phases such as CeIn₃, misoriented CeCoIn₅ along the (112) and (h00). Our results provide a set of deposition parameters that produce high-quality epitaxial CeCoIn₅ thin films with sufficiently low amounts of impurity phases and can serve as a reference for future studies to optimize the deposition process further.

• Journal of Welding and Joining
• /
• 제31권2호
• /
• pp.57-62
• /
• 2013

Magnesium has good castability and limited workability, so its products have been manufactured by almost casting processes. In this study, a pulsed Nd:YAG laser was used to butt-weld the sand casting magnesium alloys. And the effect of welding conditions such as peak power, pulse width, welding speed was evaluated in detail. As a result of this study, large underfill and plenty of spatter taken place under the conditions with high peak power. Thus, it is recommended to use low peak power and long pulse width to obtain good welds with deep penetration. It is also confirmed that the welding speed and pps(pulse per second) are directly connected at weld defects such as underfill, porosity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.57-60
• /
• 2000

In this paper, it is purpose to develop a pulsed $CO_2$ laser with stable output at pulse repetition rate range of 2 KHz. We used a IGBT as a switching device. The laser cavity was fabricated as an axial and water cooled type. It was used a ring blower to increase a cooling effect The laser performance characteristics as parameters, such as pulse repetition rate, gas pressure have been investigated. The experiment was done under 3 electrode-type instead of 2 electrode-type. To achieve 3 electrode-type, we used two pulse-transformers which is operated parallel. As a result, the maximum output was about 28 W at the total pressure of 20 Torr, the gas mixture $Co_2$:$N_2$:He=1:9:15 and the pulse repetition rate of 1300 Hz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1710-1713
• /
• 2002

Recently, the pulsed power system has been used to many applications. Such as remediation of environmental hazards, food sterilization, air pollution control E/P (Electrostatic Precipitator), DeNOx/DeSOx power system, ozone generator, high energy physics, and other power source applications. A pulse energy efficiency for load depends on the rising time, peak value. Pulse duration and impedance matching etc. The pulsed power system generally required for short pulse duration and high peak value was forced to consider its volume and economy. In this paper, we investigated operating characteristics of the CO2 laser using an inductively pulsed power system.

• Journal of Photoscience
• /
• 제5권1호
• /
• pp.39-43
• /
• 1998

Pulsed Er: YAG and CO$_2$ lasers induced temperature rise of tissue is studied using axisymmetric, two-dimensional, and transient Pennes bio-heat equation for elucidating the implications of skin resurfacing. Modeling indicates that Er:YAG laser induced temperature has much higher but more shallow distribution in tissue than that of the CO$_2$ laser because of much higher absorption coefficient. The increase of repetition rate does not much affect on temperature rise because these laser modalities have much shorter heat diffusion time than the temporal length of each off-pulse. This model works as a tool to understand the photothermal effect in the laser-tissue interaction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계합동학술대회 논문집
• /
• pp.172-175
• /
• 2002

The technique of induced discharge by a pulsed CO2 laser is being applied to control electrical discharge path, material processing, triggered lightning for protecting the power equipments. In this paper, we have investigated about the characteristics of the induced discharge at atmospheric conditions by using a plasma channel, which is produced when a pulsed CO2 laser radiation is focused by a focusing mirror as a trigger source. A plasma channel produced by laser radiation has an effect on decreasing the threshold voltage and inducing the discharge in both needle electrodes. We have confirmed a delay time between a produced plasma channel and an electrical discharge after laser radiation. We provided the decreased voltage lower than the natural discharge voltage between electrode type of needles and was induced the discharge by forming a plasma channel between them. In this research we could understand the time delay of induced discharge by laser radiation, and the characteristics of the discharge cause by the decrease in the threshold voltage, and the polarity effect by changes of plasma channel positions between two electrodes.

• 한국세라믹학회지
• /
• 제41권8호
• /
• pp.593-598
• /
• 2004

1 $\mu$m이하의 전고상 리튬 박막전지의 구현을 위해 펄스 레이저 증착법을 이용하여 Pt/TiO$_2$/SiO$_2$/Si 기판위에 LiCoO$_2$정극을 증착온도와 Li/Co 간의 몰 비율을 변화시켜가며 성장시켰다. 특히, Li/Co=1.2의 조성을 갖는 LiCoO$_2$를 50$0^{\circ}C$의 증착온도에서 성장시킬 경우 53 $\mu$Ah/$cm^2$-$\mu$m의 높은 초기 용량값을 가지며 100 싸이클 후에도 67.6%의 용량값을 유지하였다. LiCoO$_2$/Pt/TiO$_2$/SiO$_2$/Si위에 고체 전해질인 (Li, La)TiO$_3$를 비정질상으로 하여 PLD방법으로 낮은 온도대역에서 증착온도를 다양하게 하여 증착하였다. 10$0^{\circ}C$의 증착온도에서 LiCoO$_2$Pt/TiO$_2$/SiO$_2$/Si위에 성장시킨 (Li, La)TiO를 가지고 LiClO$_4$ in PC 안에서 Li anode와 충$.$방전 측정 결과 약 51$\mu$Ah/$cm^2$-$\mu$m의 초기 용량값을 나타내었으며 100싸이클 후에도 90%의 훌륭한 방전용량의 보존력을 나타내었다. 비정질상의 (Li, La)TiO$_3$ 고체 전해질은 전고상 박막전지로의 구현이 가능하다.

• 한국컴퓨터산업학회논문지
• /
• 제2권8호
• /
• pp.1055-1062
• /
• 2001

본 연구에서는 1KHz 부근의 펄스 반복율을 가지는 경제적이고 컴팩트한 펄스형 $CO_2$ 레이저의 개발에 관해서 기술하였다. 고압 고주파 펄스 변압기와 수 십 KHz의 스위칭에 적합한 IGBT를 사용한 고압 펄스전원 장치를 레이저 공진기에 접목시켜 새로운 방식의 고반복 $CO_2$ 레이저 장치를 개발하였다. 전원장치에 사용된 2개의 IGBT를 정밀하게 제어하기 위해서 제어부에는 PIC 마이크로프로세서가 사용되었고 공진기는 수냉방식의 저속축류형으로 제작되었다. 완성된 장치의 펄스 반복율과 동작압력 그리고 레이저 매질 가스의 혼합비의 변화에 따른 레이저빔의 출력 특성실험을 통하여 가스 배압비 $CO_2$： $N_2$：He ＝ 1：9：15펄스 반복율 700 Hz, 동작압력 15 Torr에서 최대 레이저 출력 약 20.5 W, 최대 효율 약 8%를 달성하였다.