• Journal of Electrical Engineering and information Science
• /
• v.3 no.3
• /
• pp.316-321
• /
• 1998

In recent years, concern has been raised about the technique of controlling electrical breakdown by using laser in many fields. Especially, laser has attracted much attention in the Electro-Discharge Macining(EDM) because of its many merits. Therefore, this research has been performed to obtain fundamental data relevant to discharge processing by using a pulsed Nd:YAG laser. The experiments of laser-guided dc discharge by laser radiation have been carried out at low air pressure ranging from 0.2 to 20 torr. The minimum laser-guided dc discharge voltage V\ulcorner at the given pressures P and distances D between an anode and a cathode was measured. It is found that the minimum laser-guided dc discharge voltage is much lower than the natural discharge voltage V\ulcorner\ulcorner, and the values of V\ulcorner and V\ulcorner as a function of P.D has a similar tendency. The laser output energy Eout decreases with input pulse duration tp increasing, and the more the value of tp increases, the higher that of V\ulcorner is obtained because the number of photons during the discharge time N decreases with t\ulcorner increasing. There is the time lag frequently when the discharge by laser radiation is misguided under the condition of the applied voltage less than V_G.min.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.595-599
• /
• 2002

Edge welding of thin sheets is very difficult because of the fit-up problem and small weld area In laser welding, joint fit-up and penetration are critical for sound weld quality, which can be monitored by appropriate methods. Among the various monitoring systems, visual monitoring method is attractive because various kinds of weld pool information can be extracted directly. In this study, a vision sensor was adopted for the weld pool monitoring in pulsed Nd:YAG laser edge welding to monitor whether the penetration is enough and the joint fit-up is within the requirement. Pulsed Nd:YAG laser provides a series of periodic laser pulses, while the shape and brightness of the weld pool change temporally even in one pulse duration. The shutter-triggered and non-interlaced CCD camera was used to acquire a temporally changed weld pool image at the moment representing the weld status well. The information for quality monitoring can be extracted from the monitored weld pool image by an image processing algorithm. Weld pool image contains not only the information about the joint fit-up, but the penetration. The information about the joint fit-up can be extracted from the weld pool shape, and that about a penetration from the brightness. Weld pool parameters that represent the characteristics of the weld pool were selected based on the geometrical appearance and brightness profile. In order to achieve accurate prediction of the weld penetration, which is nonlinear model, neural network with the selected weld pool parameters was applied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.305-306
• /
• 2008

본 논문에서는 PRAM 에서 기록매질로 이용될 수 있는 최적의 물질을 찾고자 $Ge_2Sb_2Te_5$ 박막에 Al을 첨가하여 비정질-결정질 천이시의 원자구조와 상변화 특성간의 관계를 연구하였다. 이 실험에 사용된 $Al_x(Ge_2Sb_2Te_5)_{1-x}$ 조성은 5N의 금속 파우더를 용융-냉각법으로 벌크를 제작하였고 열증착 방법으로 Si (100) 및 유리 (corning glass, 7059) 기판위에 200nm 두께로 박막을 증착하였다. 비정질 박막의 상변화에 따른 반사도 차이를 평가하기 위해서 658 nm의 LD가 장착된 나노펄스 스캐너를 이용하여 power; 1~17mW, pulse duration; 10~460 ns의 범위에서 각 조성의 비정질-결정질 상변화속도를 측정, 비교 분석하였다. 또한 각각의 박막을 $100^{\circ}C$ 에서 $400^{\circ}C$ 까지 $50^{\circ}C$ 간격으로 $N_2$ 분위기에서 1시간동안 열처리 한 후 XRD와 UV-Vis-NIR spectrophotometer를 사용하여 각 상의 구조분석 및 광학적 특성을 분석하였다. 또한 4-point probe로 면저항을 측정하였다.

• Investigative Magnetic Resonance Imaging
• /
• v.4 no.1
• /
• pp.20-26
• /
• 2000

Gradient moment nulling techniques require the introduction of an additional gradient on each axis for each order of motion correction to be applied. The additional gradients introduce new constraints on the sequence design and increase the demands on the gradient system. The purpose of this paper is to demonstrate techniques for optimization of gradient echo gradient moment nulling sequences within the constraints of the gradient hardware. Flow compensated pulse sequences were designed and implemented on a clinical magnetic resonance imaging system. The design of the gradient moment nulling sequences requires the solution of a linear system of equations. A Mathematica package was developed that interactively solves the gradient moment nulling problem. The package allows the physicist to specify the desired order of motion compensation and the duration of the gradients in the sequence with different gradient envelopes. The gradient echo sequences with first, second, and third order motion compensation were implemented with minimum echo time. The sequences were optimized to take full advantage of the capabilities of the gradient hardware. The sequences were used to generate images of phantoms and human brains. The optimized sequences were found to have better motion compensation than comparable standard sequences.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.84-89
• /
• 1994

A tunable pulsed dye laser was operated in a single longitudinal mode by injection locking with a cw ring dye laser. A doubled Nd:YAG laser was used as the pumping source. Phase sensitive detection technique was applied to maintain the required match between the master laser frequency and the slave resonator cavity length. The fluctuation of the center frequency of the pulsed laser was < 10 MHz, and the pulse duration (FWHM) was 6 ns. The linewidth measured by scanning confocal interferometer was 130 MHz. When pumped by 50 mJ of the doubled Nd:YAG laser, the output energy of the pulsed dye laser was 2 mJ and the peak power was 330 kW. 30 kW.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.135-139
• /
• 2016

I propose a vector passive harmonic mode-locked fiber laser based on topological insulator Bi2Se3 interacting with a fiber taper with a diameter of 7 μm. The particles of topological insulator are deposited uniformly onto the fiber taper with light pressure effect. By incorporating the fabricated saturable absorber into an Er-doped fiber laser cavity, stable mode-locked fiber is obtained. Due to the intense evanescent field of the fiber taper, strong confinement of light enhances the nonlinearity of the laser cavity, and passive harmonic mode-locking is performed. I observe a maximum harmonic mode-locking of 356th, corresponding to a frequency of 3.57 GHz. The pulse duration is 824 fs, and the full width at half maximum of the spectrum is about 8.2 nm. The polarization dependent loss of the saturable absorber is ~ 2.5 dB in the wavelength range of the C band. As the cavity contains no other polarization dependent device, the mode-locked laser is functioning in the vector state. The harmonic order vs pump power is investigated. To the best of our knowledge, this report is the highest frequency mode-locked fiber laser based on Bi2Se3. Experimental results indicate that the topological insulator Bi2Se3 functioning with a thin fiber taper is effective for vector harmonic mode-locking.

• Applied Microscopy
• /
• v.25 no.3
• /
• pp.1-19
• /
• 1995

The present study was performed to clarify the effect of vagus nerve stimulation on the enterochromaffin(EC) cells in the body of the stomach, the first part of the duodenum and the ceceum of rats by using routine electron microscopy and immunogold labelling. The changes in the ultrastructure and in the labelling density of the gold particles of the EC cells were investigated after vagus nerve stimulation. The vagus nerve was electrically stimulated with a square wave pulse generator for a duration of 5 minutes each, a total of 8 times at 2 minute intervals. Immunogold labelling demonstrated that the epithelial serotonin immunoreactive cells of the gastrointestinal tract are EC cells containing characteristic pleomorphic granules. Immunocytochemically labelled gold particles were largely concentrated in the dense matrix of the granules of the EC cell, and the labelling density of the gold particles considerably increased after the vagus nerve stimulation. Except for a slight activation of Golgi complexes, no remarkable changes in the ultrastructures of the EC cells were noted after the vagus nerve stimulation. The above results suggest that vagus nerve stimulation may activate serotonin biosynthesis in EC cells.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.5
• /
• pp.685-692
• /
• 2012

UV technology is widely used in water and wastewater treatment. Many researches have been conducted on microbial disinfection and micro pollutant reduction with UV treatment. However, the study on NOM with UV has limited because low/medium pressure UV lamp is not sufficient to affect refractory organics such as NOM. Pulsed UV treatment using UV flash lamp can be operated in the pulsed mode with much greater peak intensity. The pulse duration is typically in microseconds, whereas the interval between pulses is in the order of milliseconds. The high intensity of pulsed UV would mineralize NOM itself as well as change the characteristics of NOM. Chlorine demand and DBPs formation is affected on the changed amounts and properties of NOM. The objective of this study is to investigate the effect on NOM, chlorine residual, and chlorinated DBPs formation with pulsed UV treatment.

• Korean Journal of Adult Nursing
• /
• v.14 no.3
• /
• pp.418-427
• /
• 2002

Purpose: The Purpose of this research was to develop the integrative exercise program for the elderly. Method: The first step was to survey the elder's health status and general health problems. The second step was to design the exercise type, intensity, time and frequency. Result: 1. Elders who implement the integrative exercise program had weaker health status, lower physical performance and more depression than any other places. 2. The integrative exercise program developed the preparation stage composed of stretching and Yudongkong-Ki exercise, the central stage was composed of range of motion exercise, muscle strength exercise and aerobic exercise with favorite and popular Korean music. The finishing stage was composed of joint rounding and Yudongkong-Ki exercise. The exercise intensity was RPE(rating perceived exertion) 10-11, maximal pulse rate 40-60%, duration started from 20min to 50min and frequency is 2-3times/wk. Conclusion: The integrative exercise program developed by the researcher is tailored exercise that is more applicable to individual cases in community settings. Eventually, the program is safely applicable to the elders, and is expected to improve the elders' physical function and quality of life.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1141-1149
• /
• 2013

Dimensional analysis is an important tool for developing mathematical models of physical phenomena in order to understand the effects of laser shock peening(LSP) process parameters. By using the Bucking ${\prod}$ theorem, we proposed an applicable dimensional analysis method to verify the effects of LSP process parameters on the residual stresses. Furthermore, by using finite element analysis, we proposed a finite element method of LSP and discussed various parameters, such as peak pressure, pressure pulse duration, laser spot size, and multiple LSPs.