• 대한한의진단학회지
• /
• 제12권2호
• /
• pp.8-17
• /
• 2008

Objectives: For the traditional pulse diagnosis in Oriental Medicine, not only the pulse shape in time domain, but the width, length and depth of arterial pulse also should be measured. However, conventional pulse diagnostic systems have failed to measure the spatial parameters of the arterial pulse e.g. effective length of arterial pulse in the wrist. In fact, there are many ways to measure that kind of spatial features in arterial pulsation, but among them, the method using image sensor provides relatively cheap and simple way, therefore I tested feasibility of measuring 2-dimensional pressure distribution by imaging devices. Methods: Using widely used PC cameras and dotted balloons, the subtle oscillation of skin over the radial artery was recorded continuously, and then the displacement of every dot was calculated. Consequently, the time course of that displacements shows arterial pulse wave. Results: By the proposed method I could get pressure distribution map with 30Hz sampling rate, 21steps quantization resolution, and approximately 1mm spatial resolution. With reduced quantization resolution, $3cm{\times}4cm$ view angle could be achieved. Conclusion: Although this method has some limitations, it would be useful method for detecting 2-dimensional features of arterial pulse, and accordingly, this method provides a novel way to detect 'narrow pulse', 'wide pulse', 'long pulse', 'short pulse', and their derivatives.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.415-418
• /
• 1995

This paper describes a new technique for thickness measurement of a very thin layer less than one-quarter of the wavelength of ultrasonic wave using ultrasonic pulse-echo method. The technique determines the thickness of a thin layer in a layered medium form the amplitudes of the total reflected waves from the back side layer of interst. Thickness of a very thin layer few inch deep inside the media can be measured without using a very high frequency ultrasonic transducer over 100MHz which must be used in the conventional techniques for the precision measurement of a thin layer. The method also requires no inversion process to extract the thickness from the waveform of the reflected waves, so that it makes possible on-line measurement of the thickness of the layer.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.476-481
• /
• 1999

This paper describes a new technique for measurement of the displacement less than one-quarter of the wavelength of ultrasonic wave using ultrasonic pulse-echo method. The technique determines the displacement of a journal bearing from the amplitudes of the total reflected waves from the surface of journal inside the bearing. Vibration of journal bearing can be measured without using a very high frequency ultrasonic transduce over 100MHz which must be used in the conventional techniques for the precision measurement of a small displacement. The method also requires no inversion process to extract the thickness from the waveforms of the reflected waves, so that it makes possible on-line measurement of the vibration of journal bearing.

• 비파괴검사학회지
• /
• 제36권2호
• /
• pp.138-148
• /
• 2016

Measurement of elastic constants is crucial for engineering aspects of predicting the behavior of materials under load as well as structural health monitoring of material degradation. Ultrasonic velocity measurement for material properties has been broadly used as a nondestructive evaluation method for material characterization. In particular, pulse-echo method has been extensively utilized as it is not only simple but also effective when only one side of the inspected objects is accessible. However, the conventional technique in this approach measures longitudinal and shear waves individually to obtain their velocities. This produces a set of two data for each measurement. This paper proposes a simultaneous sensing system of longitudinal waves and shear waves for elastic constant measurement. The proposed system senses both these waves simultaneously as a single overlapped signal, which is then analyzed to calculate both the ultrasonic velocities for obtaining elastic constants. Therefore, this system requires just half the number of data to obtain elastic constants compared to the conventional individual measurement. The results of the proposed simultaneous measurement had smaller standard deviations than those in the individual measurement. These results validate that the proposed approach improves the efficiency and reliability of ultrasonic elastic constant measurement by reducing the complexity of the measurement system, its operating procedures, and the number of data.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.489-492
• /
• 2005

Even though the blood pressure is one of the most widely used index for the healthcare monitoring of hypertensive and normotensive persons, there is no non-intrusive measurement method which is commercialized until now. Pulse Arrival Time (PAT) is known that it has close relation with the systolic blood pressure (SBP) and arterial stiffness. In this study, SBP estimation methods by non-intrusive measurement of PAT are suggested. For the unconstrained measurement of PAT, the first method used the electrically non contact electrocardiogram (ENC-ECG) technique and the reflective type of Photoplethysmography (PPG) sensor on the computer mouse. In the second method, ENC-ECG and the air pressure sensor in the seat cushion on a chair were measured. The third method used ECG electrodes and PPG sensors on the toilet seat cover. The validation and regression analysis of the relationship of PAT and SBP are summarized. These methods have considerable errors to be used for all people. But these can be applied for each subject after the parameter customization within acceptable error. So, it is feasible for suggested methods to be used for monitoring of SBP in daily life in non-intrusive way when there is personal identification system of each subject.

• 전자공학회논문지A
• /
• 제30A권8호
• /
• pp.27-33
• /
• 1993

This paper presents a mobile measurement technique of the ghost-flutter caused in mobile television reception. The ghost-flutter is caused by timing variation of the television horizontal synchronizing pulse due to frequency selective fading in a multipath propagation environment. The ghost-flutter can be detected by measuring the dynamic timing variation of horizontal synchronizing pulse. Especially, in this paper, a technique for measuring horizontal synchronizing timing fluctuations which cause the ghost-flutter is developed, using a Rubidium oscillator as a time standard with high stability.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2014년도 추계학술대회
• /
• pp.965-966
• /
• 2014

초음파를 이용한 거리 및 속도측정에서는 PRF(Pulse Repitition Frequency) 선정에 따른 거리 및 속도 모호성 문제가 큰 장애 요인 중의 하나이다. 따라서 이러한 장애 극복을 위한 신호파형 발생시 PRF 선정 방법과 측정 결과에 미치는 영향을 분석하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.444-446
• /
• 2009

현재 대다수의 맥박(또는 심박) 측정 장치는 electrodes와 PPG로 국한되어 있다. 그러나 electrodes는 착용자의 불편감과 수입 의존성에 의한 높은 가격이라는 단점을 가지고 있으며, PPG는 동잡음에 약하다는 단점을 갖는다. 본 논문에서는 PPG와 flexible sensor를 동시 적용하여 상호 작용하게 함으로서 각 센서들의 단점을 보완 해줄 수 있는 하이브리드형의 맥박 측정 장치에 대하여 연구하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 춘계학술대회
• /
• pp.1020-1022
• /
• 2013

본 논문에서는 펄스방사선 선량 측정을 위한 Peak Detector를 설계하였다. 펄스방사선은 수ns ~ 수십ns의 초고속의 신호로 Peak 값을 측정하기 어렵다. Peak Detector는 센서에서 발생한 Peak 전압을 수ms 동안 유지하므로 ADC를 이용하여 데이터를 쉽게 측정할 수 있다. Peak Detector 시뮬레이션 결과 Peak 값을 1ms 이상 유지하는 것을 확인하였으며 펄스방사선 조사시험 결과 $1.95{\times}10^6rad/s$의 선량을 확인하였다.

• International Journal of Concrete Structures and Materials
• /
• 제1권1호
• /
• pp.83-88
• /
• 2007

This paper discusses a method of measuring transient potential response of a corrosion interface to a small galvanostatic pulse perturbation for a rapid assessment of the corrosion rate of reinforcing steel in concrete structures. Measurements were taken on 100 mm sections of steel bars which were subjected to a wide range of corrosion conditions, from passive steel to actively corroding steel. The duration of the applied galvanostatic pulse was varied between 5s and 180s, and the lateral distance of the point of measurement on the steel bar varied from zero to 400 mm. The result of the electrochemical transient response was investigated using a typical sampling rate of 1 kHz. Analysis of the transient potential response to the applied galvanostatic pulse has enabled the separation of equivalent electronic components so that the components of a series of capacitances and resistances, whose values are dependent on the corrosion condition of the reinforcing steel, could be isolated. The corrosion rate was calculated from a summation of the separate resistive components, which were associated with the corrosion interface, and was compared with the corrosion rate obtained from linear polarization resistance (LPR) method. The results show that the galvanostatic pulse transient technique enables the components of the polarization resistance to be evaluated separately so as to give more reliable corrosion rate values than those obtained from the LPR method. Additionally, this paper shows how the galvanostatic pulse transient response technique can be implemented. An appropriate measurement time for passive and actively corroding reinforcing steel is suggested for the galvanostatic pulse transient response measurements in the field site.