• Journal of Power Electronics
• /
• 제15권2호
• /
• pp.309-318
• /
• 2015

This study proposes a dual-output single-stage bridgeless single-ended primary-inductor converter (DOSSBS) that can completely remove the front-end full-bridge alternating current-direct current rectifier to accomplish power factor correction for universal line input. Without the need for bridge diodes, the proposed converter has the advantages of low component count and simple structure, and can thus significantly reduce power loss. DOSSBS has two uncommon output ports to provide different voltage levels to loads, instead of using two separate power factor correctors or multi-stage configurations in a single stage. Therefore, this proposed converter is cost-effective and compact. A magnetically coupled inductor is introduced in DOSSBS to replace two separate inductors to decrease volume and cost. Energy stored in the leakage inductance of the coupled inductor can be completely recycled. In each line cycle, the two active switches in DOSSBS are operated in either high-frequency pulse-width modulation pattern or low-frequency rectifying mode for switching loss reduction. A prototype for dealing with an $85-265V_{rms}$ universal line is designed, analyzed, and built. Practical measurements demonstrate the feasibility and functionality of the proposed converter.

• Nuclear Engineering and Technology
• /
• 제52권1호
• /
• pp.101-108
• /
• 2020

In order to solve the contradiction between requirements of high sampling rate for acquiring accurate energy information of pulses and large amount of data to be processed timely, the method with an algorithm to correct errors caused by reducing the sampling rate is normally used in front-end read-out system, which is conductive to extract accurate energy information from digitized waveform of pulse. The functions and effects of algorithms, which mainly include polynomial fitting with different fitting times, double exponential function fitting under different sampling modes, and integral area algorithm, are analyzed and evaluated, and some meaningful results is presented in this paper. The algorithm described in the paper has been used preliminarily in a prototype system of Positron Emission Tomography (PET) for heavy-ion cancer therapy facility.

• Nuclear Engineering and Technology
• /
• 제53권10호
• /
• pp.3421-3430
• /
• 2021

Spherical NaI(Tl) detectors are used in gamma-ray spectrometry, where the gamma emissions come from the nuclei with energies in the range from a few keV up to 10 MeV. A spherical detector is aimed to give a good response to photons, which depends on their direction of travel concerning the detector center. Some distortions in the response of a gamma-ray detector with a different geometry can occur because of the non-uniform position of the source from the detector surface. The present work describes the calibration of a NaI(Tl) spherical detector using both an experimental technique and a numerical simulation method (NSM). The NSM is based on an efficiency transfer method (ETM, calculating the effective solid angle, the total efficiency, and the full-energy peak efficiency). Besides, there is a high probability for a source-to-detector distance less than 15 cm to have pulse coincidence summing (CS), which may occur when two successive photons of different energies from the same source are detected within a very short response time. Therefore, γ-γ ray CS factors are calculated numerically for a ¹⁵²Eu radioactive cylindrical source. The CS factors obtained are applied to correct the measured efficiency values for the radioactive volumetric source at different energies. The results show a good agreement between the NSM and the experimental values (after correction with the CS factors).

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권3호
• /
• pp.3-6
• /
• 2008

Electrolytic in-process dressing (ELID) grinding is a new technique for achieving a nanoscale surface finish on hard and brittle materials such as optical glass and ceramics. This process applies an electrochemical dressing on the metal-bonded diamond wheels to ensure constant protrusion of sharp cutting grits throughout the grinding cycle. In conventional ELID grinding, a constant source of pulsed DC power is supplied to the ELID cell, but a feedback mechanism is necessary to control the dressing power and obtain better performance. In this study, we propose a new closed-loop wheel dressing technique for grinding wheel truing that addresses the efficient correction of eccentric wheel rotation and the nonuniformity in the grinding wheel profile. The technique relies on an iterative control algorithm for the ELID power supply. An inductive sensor is used to measure the wheel profile based on the gap between the sensor head and wheel edge, and this is used as the feedback signal to control the pulse width of the power supply. We discuss the detailed mathematical design of the control algorithm and provide simulation results that were confirmed experimentally.

• 조명전기설비학회논문지
• /
• 제21권4호
• /
• pp.19-27
• /
• 2007

This paper presents a novel soft-switching PWM utility frequency AC to high frequency AC power conversion circuit incorporating boost H-bridge inverter topology, which is more suitable and acceptable for cost effective consumer induction heating applications. The operating principle and the operation modes are presented using the switch mode equivalent circuits and the operating voltage and current waveforms. The performances of this high-frequency inverter using the latest IGBTs are illustrated, which includes high frequency power regulation and actual efficiency characteristics based on zero voltage soft-switching(ZVS) operation ranges, and the power dissipation as compared with those of the conventional type high frequency inverter. In addition, a dual mode control scheme of this high frequency inverter based on asymmetrical pulse width modulation(PWM) and pulse density modulation(PDM) control scheme is discussed in this paper in order to extend the soft switching operation ranges and to improve the power conversion efficiency at the low power settings. The power converter practical effectiveness is substantially proved based on experimental results from practical design example.

• 대한전자공학회논문지
• /
• 제27권4호
• /
• pp.491-501
• /
• 1990

Recently, four speech coding techniques, namely, SBC-APCM(sub-band coding adaptive PCM), RPE-LPC(regualr pulse excitation linear predictive codec), MPE-LTP(multi-pulse excited long-term prediction) and CELP (code-excited linear prediction) are proposed for digital mobile radio applications. However, a performance comparison of these coders in the Rayleigh fading environment has not been made yet. In this paper, the performances of the four spech coders in the random bit error and burst error environment are investigated. For the channel coding of SBC-APCM, RPE-LPC and MPE-LTP, the sensitivity of output bit stream is measured and a bit selective forward error correction is provided acording to the measured bit sensitivity. And for an attempt to improve the performance of CELP, an optimum quantizer is applied for transmitting scalar quantities in CELP. However, an improvement over the conventional approach is found to be negligible. For the channel coding of CELP, Reed-Solomon code, Golay code, convolutional code of rate 1/2 shows the best performance. Finally, from the simulation results, it is concluded that CELP is the best candidate for digital mobile radio and is followed by MPE-LTP, SBC-APCM and RPE-LPC.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.102-110
• /
• 2016

In this paper, a high-frequency dual mode control LLC resonant converter with wide input voltage range is proposed through zero voltage switching (ZVS) under the universal line input voltage and every load conditions. Conventional small power adapter driving should be satisfied with universal line input voltage because it has no power factor correction circuit regulation. The conventional LLC resonant converter for an adapter can reduce the size of transformer in terms of high-frequency driving and ZVS. However, this converter has a disadvantage in terms of design of resonant tank under various input voltages because the frequency modulation range is very wide to satisfy voltage conversion gain. Compared with the conventional one, the proposed LLC converter can be adapted to universal line input voltage and high-frequency driving because it is controlled by pulse width modulation and pulse frequency modulation with control voltage. The validity of the proposed LLC converter is proved through the 60 W prototype.

• Nuclear Engineering and Technology
• /
• 제50권7호
• /
• pp.1006-1016
• /
• 2018

Since the early forties, researchers from around the world have been studying the phenomenon of deadtime in radiation detectors. Many have attempted to develop models to represent this phenomenon. Two highly idealized models; paralyzable and non-paralyzable are commonly used by most individuals involved in radiation measurements. Most put little thought about the operating conditions and applicability of these ideal models for their experimental conditions. So far, there is no general agreement on the applicability of any given model for a specific detector under specific operating conditions, let alone a universal model for all detectors and all operating conditions. Further the related problem of pile-up is often confused with the deadtime phenomenon. Much work, is needed to devise a generalized and practical solution to these related problems. Many methods have been developed to measure and compensate for the detector deadtime count loss, and many researchers have addressed deadtime and pulse pile-up. The goal of this article is to summarize the state of science of deadtime; measurement and compensation techniques as proposed by some of the most significant work on these topics and to review the deadtime correction models applicable to present day radiation detection systems.

• 비파괴검사학회지
• /
• 제25권5호
• /
• pp.391-399
• /
• 2005

레이저 유도 초음파 시스템은 놀은 공간분해능으로 스캐닝 하면서 광대역 범위에서 검사를 할 수 있는 비접촉식 검사 장치이다. 유도되는 초음파 신호의 크기는 펄스레이저의 출력에 의해서도 변화하지만, 연속발진 레이저빔이 위치하는 표면 상태에 따라서도 측정되는 초음파 세기는 크게 변화한다. 본 논문에서는 안정된 레이저 유도 초음파 시스템을 구성하기 위하여 펄스 레이저빔의 출력을 측정하여 초음파 발생 오차를 보정하였으며, 대상체 표면의 상태에 따라 크게 변화하는 측정용 레이저 간섭계의 측정 이득 변화를 매순간 측정하여 측정 오차를 보정하였다. 본 논문에서는 대상체 표면을 스캐닝 할 수 있도록 다이나믹 안정기가 부착된 레이저 유도 초음파 시스템을 개발하였다. 개발한 레이저 초음파 시스템은 스캐닝 과정에서 간섭계의 이득이 최대가 되는 순간을 적응적으로 포착하여 초음파를 발생시키고, 유도된 초음파 신호를 고속으로 샘플링 한 후에 실시간으로 신호처리를 한다. 본 논문에서는 안정적인 레이저 유도 초음파 시스템을 구성하기 위한 전체 시스템의 하드웨어 구성 방법과 제어 알고리듬에 대하여 기술한다. 또한 본 논문에서 제안한 발생오차 보정방법과 측정오차 보정 방법이 시스템의 성능 향상에 유효함을 실험을 통하여 확인하였다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2017년도 춘계공동학술대회
• /
• pp.157-157
• /
• 2017

To minimize the damage by wild birds and acquire the benefits such as protection against weeds and maintenance of water content in soil, the mulching black color vinyl after seeding should be carried out. Non-contact and non-destructive methods that can continuously determine the locations are necessary. In this study, a crop position detection method was studied that uses infrared thermal image sensor to determine the cotyledon position under vinyl mulch. The moving system for acquiring image arrays has been developed for continuously detecting crop locations under plastic mulching on the field. A sliding mechanical device was developed to move the sensor, which were arranged in the form of a linear array, perpendicular to the array using a micro-controller integrated with a stepping motor. The experiments were conducted while moving 4.00 cm/s speed of the IR sensor by the rotational speed of the stepping motor based on a digital pulse width modulation signal from the micro-controller. The acquired images were calibrated with the spatial image correlation. The collected data were processed using moving averaging on interpolation to determine the frame where the variance was the smallest in resolution units of 1.02 cm. Non-linear integral interpolation was one of method for analyzing the frequency using the normalization image and then arbitrarily increasing the limited data value of $16{\times}4pixels$ in one frame. It was a method to relatively reduce the size of overlapping pixels by arbitrarily increasing the limited data value. The splitted frames into 0.1 units instead of 1 pixel can propose more than 10 times more accurate and original method than the existing correction method. The non-integral calibration method was conducted by applying the subdivision method to the pixels to find the optimal correction resolution based on the first reversed frequency. In order to find a correct resolution, the expected location of the first crop was indicated on near pixel 4 in the inversion frequency. For the most optimized resolution, the pixel was divided by 0.4 pixel instead of one pixel to find out where the lowest frequency exists.