• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.3
• /
• pp.51-59
• /
• 1997

Dissolving pulp is a low yield(30∼35%) bleached chemical pulp that has a high cellulose content (95% or higher) suitable for use in cellulose derivatives such as rayon, cellulose acetate. This research was studied for dissolving pulp preparation as the raw material of viscose rayon from commertial pulps. (TMP, CP, DIP) In the change of pulp(cellulose) characteristics after sodium hypochlorite and solvolysis treatment. the following results were obtained In the case of sodium hypochlorite pretreatment, we have obtained pulp that high purity cellulose, but degree of polymerization was inclined to decrease less than 170∼240. Comparing sodium hypochlorite pretreatment and solvolysis pretreatment, solvolysis pretreatment is superior to sodium hypochlorite process for making dissolving pulp. We think that the low degree of polymerization of cellulose because of increasing degradation of cellulose during delignification treatment.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.22-29
• /
• 2002

This research was conducted to investigate the morphological characteristics of fine fibers produced during beating process of high yield pulp treated with ozone and the distribution of lignin in the produced fine fibers. Thermomechanical(TMP) pulp and chemithermomechanical(CTMP) pulp of spruce and CTMP of white birch were beaten to reach 200$m\ell$ CSF, and then the fine fibers were observed using ultraviolet microscope. The fine fibers produced from TMP and CTMP of spruce using treated with ozone for 15 minutes were fragments of fiber surfaces or cell corners, and most of them contained lignin. However, lignin was not observed in the fibers after 15 minutes of ozone treatment. The fine fibers produced from CTMP of white birch were broken pieces or fragments of fiber surfaces or cell corners. The lignin was observed in the fibers until 5min of ozone treatment but no lignin was observed after 5 minutes of ozone treatment. Different morphological characteristics of TMP and CTMP explained both the different morphological characteristics and the distribution of lignin observed in the fine fibers produced from the beating process of TMP and CTMP treated with ozone.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.1
• /
• pp.86-93
• /
• 2000

High Colored kraft bleaching effluent is one of the main constrains in pulp and paper industry due to its dissloved lignin derivatives. The degradation of lignin in pulp and paper mill effluent is mainly caused by white-rot fungi. This paper showed that the treatment with KS-62 fungus significantly reduced the color and chemical oxygen demand in the effluent. The amounts of Mn ions in the wastewater would play roles in the induction and activity of MnP (Managanese peroxidase). Extracellular MnP was isolated from the fungus KS-62. The treatment with the MnP had the most effective decolorizatiion in the wastewater treatment using nutrients mediu.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.68-74
• /
• 1997

This research was studied dissolving pulp for rayon production, which is not KP, SP methods but steam explosion and oxygen alkali treatment. The variation of characterization in wood cellulose after steam explosion and oxygen alkali treatment this follows. In the oxygen alkali treatment of exploded pine wood, yield of dissolving pulp was lower than steam-exploded oak wood, and we have obtained dissolving pulp that high purity cellulose, but degree of polymerization was inclined to decrease less than 200. In the case of steam-exploded oak wood, degree of polymerization was higher than steam-exploded pine wood but purity of cellulose was lower than its.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.4
• /
• pp.289-296
• /
• 2017

Pulp and paper industry produces large volumes of wastewater and residual sludge waste, resulting in many issues in relation to wastewater treatment and sludge disposal. Contaminants in pulp and paper wastewater include effluent solids, sediments, chemical oxygen demand (COD), and biological oxygen demand (BOD), which should be treated by wastewater treatment processes such as coagulation and biological treatment. However, few works have been attempted to predict the treatment efficiency of pulp and paper wastewater. Accordingly, this study presented empirical models based on experimental data in laboratory-scale coagulation tests and compared them with statistical models such as artificial neural network (ANN). Results showed that the water quality parameters such as turbidity, suspended solids, COD, and UVA can be predicted using either linear or expoential regression models. Nevertheless, the accuracies for turbidity and UVA predictions were relatively lower than those for SS and COD. On the other hand, ANN showed higher accuracies than the emprical models for all water parameters. However, it seems that two kinds of models should be used together to provide more accurate information on the treatment efficiency of pulp and paper wastewater.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.325-329
• /
• 2006

Nippon Paper Industries, Co., Ltd. declared conversion of all the bleaching process to ECF, and most of the production had converted by now. To reduce ECF bleaching cost, we found that depending on electricity supply condition of the mill, utilization of ozone bleaching could be very effective. In addition, hot acid treatment of unbleached pulp also seemed to be effective for hardwood. In this study, several conditions for each technology were examined with the pulps from our own mills to reduce bleaching cost and to keep fiber quality acceptable level. In hot acid treatment study, with mild conditions (temperature lower than $90^{\circ}C$), sufficient reduction in Kappa number and hexenuronic acids content of the pulp were observed, while pulp viscosity was maintained. Moreover, to maintain strength of bleached pulp that subjected both to ozone bleaching and hot acid treatment, recommended Kappa number after ozone bleaching was more than 3. Based on these findings, two of our mills had installed medium-consistency ozone bleaching facilities and three mills installed hot acid treatment. Especially in Yatsushiro mill, both were installed in one bleaching line (A-ZD-E/P-D sequence), and running successfully.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.1
• /
• pp.30-37
• /
• 2001

The effects of enzymatic treatment of recycled fiber were investigated to obtain the basic informations which can be used to improve the papermaking properties of recycled fiber. The recycled fibers were prepared by the repeated handsheet making and disintegrating of hardwood of hardwood and softwood kraft pulp. Novozym 342, Dinimax and Pulpzyme HC were used for enzymatic treatment. The change of fiber length distribution, freeness, contact angle and crystallinity of pulp were measured. The brightness, opacity, breaking and tear index of paper were also measured. The enzymatic treatment decreased long fiber fraction of recycled hardwood fiber, but increased long fiber fraction of recycled softwood fiber. Freeness was decreased with 0.1% enzyme and then increased again with the increase of th enzyme dosage. The improvement of flexibility of recycled fiber was obtained through the decrease of contact angle that is resulted from the decrease of crystallinity of fiber. Brightness and opacity were affected by the type of pulp and enzyme, and dosage of enzyme. Breaking length of recycled hardwood fiber was improved with enzyme treatment, but breaking length of recycled softwood fiber was decreased except for 0.01% Pulpzyme treatment. Tear index was decreased with enzymatic treatment and the lowest decrease was observed with the treatment to Pulpzyme.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.30-36
• /
• 2002

This research was conducted to investigate the feasibility of using deinked pulp of white ledger(DIP) for the manufacture of high quality premium tissue. The three types of tissues were prepared using the softener treated bleached DIP, softener treated mixed pulp of unbleached DIP and virgin pulp, and untreated mixed pulp of bleached DIP and virgin pulp, respectively, and their tensile index. softness, and brightness were measured and compared. The bulk and surface softness increased only slightly by the addition of softener(0.2% mineral oil) into the bleached DIP. The tensile index was decreased by 15∼30%, and the brightness was the range of 86% to 87% ISO. The softener(0.2∼0.8% mineral oil or dialkyl imidazoline) treatment of mixed pulp of unbleached DIP and virgin pulp Improved the bulk and surface of tissue considerably. However, the brightness was low as 85% ISO or below. Although the softness of the tissue made from bleached DIP blended with virgin pulp was the lowest among three types of tissues evaluated, its tensile index was the highest and brightness was 87∼88% ISO. Based on the results, it may be predicted that the bleached DIP blended with virgin pulp is the best raw material for the manufacture of high quality premium tissue if softener treatment is applied to mixed pulp, because the softness can be improved by the addition of softener. In general, the softness of tissue was improved with the increase in the amount of softener: However, the tensile index inversely proportional to the amount of softener added. Dialkyl imidazoline was more effective than mineral oil with respect to the improvement in softness, even though the loss in tensile index was severe with the treatment of dialkyl imidazoline.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.56-62
• /
• 2002

Alternative way of shaping fibers suitable for papermaking was introduced. Impact refining, which was done simply by hitting wet fibers with a metal weight vertically, was intended to keep the fibers from shortening and to cause mostly internal fibrillation. Virgin chemical pulp, its recycled one and OCC were used in the experiment. It was noticed from the experiment that impact refining on virgin chemical pulp kept the fiber length and increased bonding properties greatly. However, in the recycled fibers from the chemical pulp, fiber length and bonding properties were decreased. In OCC, which seems to contain fractions of semi-chemical pulp and mechanical pulp (GP), and which is recycled pulp from corrugated boxes, fiber length and bonding properties were decreased disastrously. We believe recycled cellulosic fibers (recycled chemical pulp and OCC in this case), which went through hornification, were less resistant to the mechanical impact than virgin chemical pulp. For virgin chemical pulp, impact refining allowed no significant fiber length shortening, high WRV, and high mechanical strength.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.375-380
• /
• 1999

In order to improve the optical properties of high yield pulp, bleached chemi-thermo-mechanical pulp (BCTMP) was produced from CTMP of Betula maximowicziana Regel by two staged ozone-hydrogen peroxide bleaching. This pulp was used for the evaluation of the improvement of optical properties, chemical characteristics of lignin in fiber, and the relationship between lignin and optical properties in fiber cell wall. By hydrogen peroxide treatment, the brightness was improved, but the post color number (PC No.) was not. There was little improvement on optical properties by ozone treatment, but his could be solved by using two staged ozone-hydrogen peroxide bleaching. The hydrogen peroxide treatment did not make nay change on chemical characteristics of lignin in cell wall, but by ozone treatment, it was found that the non-aromatic conjugated structure was existed in the surface of cell wall, but this could be removed by hydrogen peroxide treatment in two staged ozone-hydrogen peroxide treatment. Therefore, the optical properties was significantly improved due to the removal of non-aromatic conjugated structure.