• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.9-16
• /
• 2009

Cylindrical dry forming mould was developed to carry out a feasibility study of dry forming of papers. The effect of disintegration, forming, humidification and pressing on dry formed papers was examined. Dry disintegrated fibers showed the similar fiber length distribution to wet disintegrated fibers, but they showed distorsion and damaged appearance on the surface. Process parameters required to form a uniform fiber pad was investigated. A proper screening and air dispersion method was selected that gives proper formation. Humidification and pressing conditions were examined to get a good dry formed papers in dry forming. Results showed that dry forming method can be used to make a sheets with reasonable formation and properties.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.51-57
• /
• 2000

Cylinder machine usually gives more fiber orientation than fourdrinier and has limitation in machine speed because of fiber wash-off caused by centrifugal force when machine speed increases. This study aimed for the improvement of paper formation and productivity by setting an apron in vat inlet and by adjusting mould water head. Improvement of formation and increase of machine speed were achieved, which ultimately improve productivity. Installing an apron successfully decreased fiber wash-off. Fiber orientation and two-sideness of ash distribution became less severe. The proper adjustment of water head inside the cylinder mould proved to be an important factor not only in paper formation but also in decreasing paper two-sideness.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.55-55
• /
• 2000

Cylinder machine usually gives more fiber orientation than fourdrinier and has limitation in machine speed because of fiber wash-off caused by centrifugal force in case of adding machine speed. This study aimed at improvement of paper formation and higher productivity by setting up an apron in vat inlet and by adjustment of mould water head. As results, there were improvement of formation and increase of machine speed, which ultimately improve productivity. Setting up an apron successfully decreased fiber wash-off. Fiber orientation and two-sideness of ash distribution became less severe. These results could lead to better dimension stabilities in the CD through mitigation of fiber orientation and also could result in less curl from two-sideness of paper. The proper adjustment of water head inside the cylinder mould proved to be important factor not only in paper formation but also in decreasing paper two-sideness.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.4
• /
• pp.294-301
• /
• 2017

PURPOSE. Temperature increase of $5.5^{\circ}C$ can cause damage or necrosis of the pulp. Increasing temperature can be caused not only by mechanical factors, e.g. grinding, but also by exothermic polymerization reactions of resin materials. The aim of this study was to evaluate influences of the form material on the intrapulpal temperature during the polymerization of different self-curing resin materials for temporary restorations. MATERIALS AND METHODS. 30 provisonal bridges were made of 5 resin materials: Prevision Temp (Pre), Protemp 4 (Pro), Luxatemp Star (Lux), Structure 3 (Str) and an experimental material (Exp). Moulds made of alginate (A) and of silicone (S) and vacuum formed moulds (V) were used to build 10 bridges each on a special experimental setup. The intrapulpal temperatures of three abutment teeth (a canine, a premolar, and a molar,) were measured during the polymerization every second under isothermal conditions. Comparisons of the maximum temperature ($T_{Max}$) and the time until the maximum temperature ($t_{TMax}$) were performed using ANOVA and Tukey Test. RESULTS. Using alginate as the mould material resulted in a cooling effect for every resin material. Using the vacuum formed mould, $T_{Max}$ increased significantly compared to alginate (P<.001) and silicone (P<.001). In groups Lux, Pro, and Pre, $t_{TMax}$ increased when the vacuum formed moulds were used. In groups Exp and Str, there was no influence of the mould material on $t_{TMax}$. CONCLUSION. All of the mould materials are suitable for clinical use if the intraoral application time does not exceed the manufacturer's instructions for the resin materials.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.1931-1936
• /
• 2007

The application of high velocity air jets to heat transfer surface has tremendous engineering potential in various industries. The impinging jets are therefore widely used for their enhanced transport characteristics, especially for drying of continuous materials such as sheet, film, carpets, forming materials and pallets. This paper presents the drying characteristics of plate type material and performs the test with the change of operating conditions in conveyer band dryer using the impinging jet nozzles. The factors influencing drying rate were confirmed, also the design data of band dryer using the impinging jet was obtained.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.15 no.1
• /
• pp.1-6
• /
• 2009

The impact absorption materials made of synthetic organic chemical product like Expanded Polystyrene(EPS), Expanded Polyethylene(EPE), Expanded Polyurethane(EPU), etc. have been used with general packaging material until the present. But nowadays, the use of these materials is intended to be decreased and to be recycled in connection with environmental pollution. In addition, it has been tried to substitute these materials with non-pollution materials(natural materials) like pulp mould, paper protectors, etc. At the same time, it is required to evaluate and analyze these cushioning materials for cushioning properties based on impact and vibration, in order to make an efficiency on the overall packaging system because they are generally being used by a random choice regardless of the properties of contents and cushioning materials. Therefore, this study provides analyzed data on cushioning properties of various cushioning materials against impact and vibration, and is intended to provide more efficient model for packaging system by minimizing their using amount through choosing an optimal cushioning material as well as intended to lead to the use of nonpollution materials in case these cushioning materials have same cushioning properties.