• 펄프종이기술
• /
• 제41권1호
• /
• pp.9-16
• /
• 2009

Cylindrical dry forming mould was developed to carry out a feasibility study of dry forming of papers. The effect of disintegration, forming, humidification and pressing on dry formed papers was examined. Dry disintegrated fibers showed the similar fiber length distribution to wet disintegrated fibers, but they showed distorsion and damaged appearance on the surface. Process parameters required to form a uniform fiber pad was investigated. A proper screening and air dispersion method was selected that gives proper formation. Humidification and pressing conditions were examined to get a good dry formed papers in dry forming. Results showed that dry forming method can be used to make a sheets with reasonable formation and properties.

• 펄프종이기술
• /
• 제32권2호
• /
• pp.51-57
• /
• 2000

Cylinder machine usually gives more fiber orientation than fourdrinier and has limitation in machine speed because of fiber wash-off caused by centrifugal force when machine speed increases. This study aimed for the improvement of paper formation and productivity by setting an apron in vat inlet and by adjusting mould water head. Improvement of formation and increase of machine speed were achieved, which ultimately improve productivity. Installing an apron successfully decreased fiber wash-off. Fiber orientation and two-sideness of ash distribution became less severe. The proper adjustment of water head inside the cylinder mould proved to be an important factor not only in paper formation but also in decreasing paper two-sideness.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2000년도 춘계학술발표논문집
• /
• pp.55-55
• /
• 2000

환망초지기는 장망초지기와 달리 섬유배향성이 심할 뿐만 아니라, 초지속도를 높일 경우 실린더 회전에 따라 생긴 원심력으로 인하여 지필 파괴(wash-off)가 발생하기 때문에 속도에 제한을 받게 된다. 본 연구는 이런 점을 개선하기 위하여 forming zone과 탈수시간이 중요한 인자임을 인식하고 vat 인입부에 apron을 설치하고 mould head의 변화를 통하여 종이의 품질향상과 생산성 향상을 도모하고자 하였다. 그 결과 wash-off 의 감소로 인하여 퍼짐새(formation)의 향상은 물론 생산속도을 증가시킬 수 있어 생산성 향상을 도모할 수 있었다. 섬유 배향성 개선으로 인한 CD의 치수안정성 도모, 종이의 양면성 감소로 인한 컬 발생을 방지 할 수 있으며, 내부수위의 적절한 변경은 종이의 퍼짐새는 물론 종이구조 개선의 중요한 인자로 확인되었다.

• The Journal of Advanced Prosthodontics
• /
• 제9권4호
• /
• pp.294-301
• /
• 2017

PURPOSE. Temperature increase of $5.5^{\circ}C$ can cause damage or necrosis of the pulp. Increasing temperature can be caused not only by mechanical factors, e.g. grinding, but also by exothermic polymerization reactions of resin materials. The aim of this study was to evaluate influences of the form material on the intrapulpal temperature during the polymerization of different self-curing resin materials for temporary restorations. MATERIALS AND METHODS. 30 provisonal bridges were made of 5 resin materials: Prevision Temp (Pre), Protemp 4 (Pro), Luxatemp Star (Lux), Structure 3 (Str) and an experimental material (Exp). Moulds made of alginate (A) and of silicone (S) and vacuum formed moulds (V) were used to build 10 bridges each on a special experimental setup. The intrapulpal temperatures of three abutment teeth (a canine, a premolar, and a molar,) were measured during the polymerization every second under isothermal conditions. Comparisons of the maximum temperature ($T_{Max}$) and the time until the maximum temperature ($t_{TMax}$) were performed using ANOVA and Tukey Test. RESULTS. Using alginate as the mould material resulted in a cooling effect for every resin material. Using the vacuum formed mould, $T_{Max}$ increased significantly compared to alginate (P<.001) and silicone (P<.001). In groups Lux, Pro, and Pre, $t_{TMax}$ increased when the vacuum formed moulds were used. In groups Exp and Str, there was no influence of the mould material on $t_{TMax}$. CONCLUSION. All of the mould materials are suitable for clinical use if the intraoral application time does not exceed the manufacturer's instructions for the resin materials.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.1931-1936
• /
• 2007

The application of high velocity air jets to heat transfer surface has tremendous engineering potential in various industries. The impinging jets are therefore widely used for their enhanced transport characteristics, especially for drying of continuous materials such as sheet, film, carpets, forming materials and pallets. This paper presents the drying characteristics of plate type material and performs the test with the change of operating conditions in conveyer band dryer using the impinging jet nozzles. The factors influencing drying rate were confirmed, also the design data of band dryer using the impinging jet was obtained.

• 한국포장학회지
• /
• 제15권1호
• /
• pp.1-6
• /
• 2009

The impact absorption materials made of synthetic organic chemical product like Expanded Polystyrene(EPS), Expanded Polyethylene(EPE), Expanded Polyurethane(EPU), etc. have been used with general packaging material until the present. But nowadays, the use of these materials is intended to be decreased and to be recycled in connection with environmental pollution. In addition, it has been tried to substitute these materials with non-pollution materials(natural materials) like pulp mould, paper protectors, etc. At the same time, it is required to evaluate and analyze these cushioning materials for cushioning properties based on impact and vibration, in order to make an efficiency on the overall packaging system because they are generally being used by a random choice regardless of the properties of contents and cushioning materials. Therefore, this study provides analyzed data on cushioning properties of various cushioning materials against impact and vibration, and is intended to provide more efficient model for packaging system by minimizing their using amount through choosing an optimal cushioning material as well as intended to lead to the use of nonpollution materials in case these cushioning materials have same cushioning properties.