• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.2
• /
• pp.88-94
• /
• 2010

Cattail (Typha L.) was used as a raw material for producing both bio-ethanol and pulp for papermaking at the same time. Pretreatments of cattail stems and leaves with acid ($H_2SO_4$) and alkali (NaOH) in three different addition levels were studied before soda pulping. The acid pretreatment gave reducing sugar of 15.2% of initial weight, but alkali pretreatment close to 1%. Soda pulping of the pretreated cattail gave 3% reduction in pulp yield and less bonding properties in paper; however, refining of the pulp from the pretreated cattail with alkali restored their fiber bondings up to that of the pulp from no-pretreated cattail at equivalent freeness.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.2
• /
• pp.1-8
• /
• 2011

The presence of high silica in bamboo hinders the use of this material for production of rayon grade pulp. Research has been carried out to overcome this deficiency and improve quality of rayon grade pulp with the modification in pulping and bleaching process. Effect of acid boosted water prehydrolysis, sulphuric acid pre-treatment of unbleached pulp, chlorination stage at lower pH and treatment of bleached pulp with $SO_2$ water were evaluated. Acid boosted water prehydrolysis of chips reduces prehydrolysis time by 50 minutes as compared to water prehydrolysis. Treatment of unbleached pulp with sulphuric acid reduces ash, acid insoluble, silica, calcium and iron contents of the pulp by 56, 31, 82, 84 and 60% respectively. The addition of acid, increase in kappa factor in $C_D$ stage and combination of both were effective in removing silica in the pulp. Treatment of final bleached pulp with $SO_2$ water removes silica to a great extent and improves optical properties of the pulp as compared to $H_2SO_4$ or PAA. Pretreatment of the pulp with acid and modification in the bleaching process can reduce silica substantially and improve the quality of rayon grade bamboo pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.44-50
• /
• 2016

As a raw material for pulp and paper industry, Moso bamboo, Timber bamboo and Henon bamboo pulps were prepared by soda or soda-anthraquinone(Soda-AQ) pulping process. Soda-AQ pulp yields was higher in Henon bamboo (43.2%) than in Moso bamboo or Timber bamboo (32.7-39.2%), but quite lower than hardwood species. In Kappa number comparison, Henon bamboo pulp showed lower (16.6) with 50 min cooking to $170^{\circ}C$ than that of Moso bamboo (22.8) and Timber bamboo (18.9) with 90 min cooking to $170^{\circ}C$. Fiber length of Timber bamboo soda pulp had higher (1.46 mm) than that of Moso bamboo or Henon bamboo (1.18-1.36 mm). All three bamboo pulps showed longer average fiber length than commercial hardwood pulp. With higher pulp yield and lower Kappa number, Henon bamboo is better raw material for pulp than Moso bamboo and Timber bamboo.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.4
• /
• pp.52-57
• /
• 2009

Soda and kraft pulping experiments were carried out in order to investigate the pulping characteristics of bamboo grown in Vietnam. The merit of kraft pulping was not observed for bamboo pulping from the viewpoint of delignification and screened pulp yield. The improvements of delignification during soda and kraft pulping of bamboo were observed by the addition of AQ. The bamboo pulp leaded the bulkier structure than those made from SwBKP and HwBKP. The average fiber length was 1.62mm which is shorter than those of SwBKP, but longer than those of HwBKP. It was found that the physical properties of bamboo pulp sheet could be varied by the pulping method, cooking condition, AQ addition, bleaching and refining etc.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.21-27
• /
• 2014

As a part of the study on manufacture of low density paper by organic bulky agent treatment, the effects of cationic fatty acid bulky agent on physical and optical properties of handsheets were elucidated. The research on change of physical and optical properties of paper samples according to bulky agent concentration, pulp type, and pulp combination were carried out. The results demonstrated that an increase of the concentration of cationic fatty acid bulky agent was proportional to an increase of the bulky properties of paper samples while tensile strength decreased. Also, the more the treated concentration of cationic fatty acid bulky agent increased, the more the ISO brightness of paper samples decreased while the opacity increased. The effectiveness of bulky agent with softwood bleached kraft pulp (SwBKP) was higher than that with hardwood bleached kraft pulp (HwBKP). In addition, the effectiveness with mixed pulps was higher than that with single pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.1
• /
• pp.65-73
• /
• 2012

Nowadays, the concern on the environmental load of bleaching process gave rise to the process of ECF(elemental chlorine free) and TCF(total clorine free). These sequences are based on oxygen-derived compounds such as oxygen, ozone, and hydrogen peroxide which is used as a typical eco-friendly bleaching agent. In this study, paper mulberry pulp was bleached with hydrogen peroxide and some bleaching process were accompanied with ultrasonication in order to increase the bleaching efficiency. The best bleaching efficiency of paper mulberry pulp was obtained in the condition of hydrogen peroxide and ultrasonication(20 kHz) bleaching system at $45^{\circ}C$ for 30 min. The brightness and kappa number of paper mulberry pulp were gained to 5.09% and 3.52 respectively. and yield was slightly loosed to 2%. Therefore, the efficiency of hydrogen peroxide and ultrasonication bleaching system of paper mulberry pulp was superior to the conventional hydrogen peroxide bleaching system. Magnesium sulfate acted as a bleaching stabilizer for the increasement of yield. As a result, the yield and viscosity were increased to 2.2% and 12% respectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.5
• /
• pp.25-29
• /
• 2001

Dimethyldioxirane (DMD), which is a source of active oxygen, is effective agent that can be used in chemical pulp bleaching. In this study, delignification of kraft bagasse pulp has been carried out by using DMD. The effect of the applied charge of DMD (as active oxygen) and pH of the delignification medium were studied. The optimum conditions of the applied DMD charge and pH of the delignification reaction were achieved at pH range from 8~9, 2% of DMD (as active oxygen) and the rest of delignification reaction conditions were $25^{\circ}C$, 60 min, and 12% pulp consistency. The development of brightness per unit kappa number removal (ΔBrightness/ Δ Kappa number) has highest value at the optimum condition. The study showed that the reactivity of kraft bagasse pulp be enhanced to wards alkaline hydrogen peroxide bleaching by pulp treatment with DMD.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.35-39
• /
• 2000

Refining is very important process of fibers treatment for proper paper properties. An extent of refining is usually measured by freeness, although freeness gives complicated meanings. One of a direct way of studying the refining effects on pulp fibers is making photomicrographs of beaten fibers. The conventional microscopy like light microscopy(LM) and scanning electron microscopy(SEM) require to preserve the wet structure of pulp fibers morphologically since most of papermaking process is carried out almost entirely in water. Recently developed microscopy, especially confocal laser scanning microscopy(CLSM), offers the possibility of examining fully hydrated pulp fibers. Cross-sectional images of wet pulp fibers are also generated using optical sectioning by CLSM and image analysis in order to verify and quantify the extent of fiber wall swelling indicating the internal fibrillation. At low beating load such as 2.5 kgf, in the same freeness, breaking length is higher than that of high beating load such as 5.6 kgf. fiber wall thickness at low beating load is greater than that at high beating load. This result is accounted for the fact that internal fibrillation in the low beating load was high.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.1-8
• /
• 2009

Mountain Pine Beetle (MPB) attacked pine was evaluated for pulp quality, chemical and physical properties, and bleachability. Chemical analyses showed that the dehydroabietic acid and total acetone extractives content were higher in the year 3 (grey) attacked MPB chips and lower in the year 5 (grey) attacked MPB chips as compared to a typical SPF (spruce/pine/fir) reference. Lignin and carbohydrate content of the MPB wood chips were comparable to the SPF. Similarly, there was little difference in kappa number, pulp yield and liquor consumption between the 3 and 5 year MPB attacked wood. Likewise there was no significant difference in the resulting tear strength, burst, or tensile strength. There appeared to be an improved bleaching response in the MPB attacked pulp as compared to the SPF reference, but this was accompanied by a slightly lower bleached pulp yield and higher bleach filtrate COD and solids content.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.05a
• /
• pp.123-155
• /
• 2008