Pressure grouting is a common technique in geotechnical engineering to increase the stiffness and strength of the ground mass and to fill boreholes or void space in a tunnel lining and so on. Recently, the pressure grouting has been applied to a soil-nailing system which is widely used to improve slope stability. The soil-nailing design has been empirically performed in most geotechnical applications because the interaction between pressurized grouting paste and the adjacent ground mass is complicated and difficult to analyze. The purpose of this study is to analyze the increase of pullout resistance induced by pressurized grouting with the aid of performing laboratory model tests and field tests. In this paper, two main causes of pullout resistance increases induced by pressurized grouting were verified: the increase of residual stress; and the increase of coefficient of pullout friction. From the laboratory tests, it was found that residual stress in borehole increases by pressurized grouting and dilatancy angle could be estimated by cavity expansion theory using the measured wall displacements. From the field test results, the pullout resistance of soil-nailing with pressurized grouting was found to be 10% larger than that of soil-nailing with gravitational grouting, mainly caused by mean normal stress increase and dilatancy effect. So, the pullout resistance could be estimated by considering these two effects. The radial displacement increases with dilatancy angle increase and the dilatancy angle decreases with injection pressure increase. The measured pullout resistance obtained from field tests is in good agreement with the estimated one from the cavity expansion theory.
International Journal of Naval Architecture and Ocean Engineering
/
제6권1호
/
pp.87-97
/
2014
In this study, the model tests were conducted on the short piles installed in sands under a horizontal pullout load to investigate their behavior characteristics. From the horizontal loading tests where dimensions of the pile diameter and length, and loading point were varied, the horizontal pullout resistance and the rotational and translational movement pattern of the pile were investigated. As a result, the horizontal pullout resistance of the pile embedded in sands was dependent on the pile length, diameter, loading point, etc. The ultimate horizontal pullout load tended to increase as the loading point (h/L) moved to the bottom from the top of the pile, regardless of the ratio between the pile length and diameter (L/D), reached the maximum value at the point of h/L = 0.75, and decreased afterwards. When the horizontal pullout load acted on the upper part above the middle of the pile, the pile rotated clockwise and moved to the pullout direction, and the pivot point of the pile was located at 150-360mm depth below the ground surface. On the other hand, when the horizontal pullout load acted on the lower part of the pile, the pile rotated counterclockwise and travelled horizontally, and the rotational angle was very small.
인발 저항각이라는 새로운 개념은 토목섬유로 보강된 지반에서 인발 시험을 행할 때 발생되는 마찰력, 점착력, 수동저항을 포함하는 것이다. 인발 면적을 계산함에 있어 분포 면적법을 사용하였는데, 이는 그리드에 발생되는 인장력 곡선을 이용하는 방법이다. 분포면적비는 화강토나 표준사 지반에서 거의 비슷한 결과를 나타내었다. 인발 저항각은 낮은 구속하중인 $0.2kg/cm^2$일 때는 마찰각보다 더 큰 값을 보이지만, 높은 구속하중인 $0.8kg/cm^2$일 때는 마찰각보다 더 작은 각을 보였다.
본 연구에서는 말뚝에 작용하는 구속압과 지반의 세립분 함유율을 고려한 말뚝 인발실험을 실시하였다. 그리고 실험 결과를 이용하여 말뚝의 인발저항에 미치는 지중 구속압의 영향을 분석하여 인발저항정수를 고찰하였다. 인발실험 결과, 모형지반의 세립분 함유율과 구속압의 크기에 관계없이 약 7mm~9mm의 인발변위에서 최대인발저항력이 발생되었다. 말뚝의 최대인발저항력은 모형지반의 세립분 함유율이 증가할수록 감소하였고, 이러한 경향은 구속압이 클수록 현격하게 나타났다. 말뚝인발실험 결과의 신뢰성을 검토하기 위해 인발저항력을 이론식으로 산정해 실험결과와 비교한 결과, 모든 구속압 조건에서 세립분 함유율 증가에 따라 실험값과 이론값 모두 동일하게 인발저항력이 감소하는 경향을 보였다. 인발저항정수에 대한 분석 결과, 말뚝과 지반의 경계에서 발생하는 인발저항력에 있어서 주변 지반의 세립분 함유율이 증가할수록 경계면 마찰각보다 부착력의 영향이 커지는 것을 확인하였다.
A in-situ experiment was performed to evaluate the pullout resistance capacity of chains which is used as a reinforcement of reinforced earth wall. It was also considered that chain was combined with a bar or L-type steel angle by the transverse reinforcement member in the experiment. As a result of experiment, it is expected that chain can be safely used as reinforcements of reinforced earth wall, although it is concerned that a theoretical estimation of the pullout resistance capability of chain is too conservative.
압력식 쏘일네일링 공법은 지반에 네일을 삽입한 후 압력그라우팅을 수행하여 지반과 그라우팅 사이의 인발저항력 증가를 활용한 공법으로 원지반의 강도를 최대한 활용한 공법이다. 최근들어, 쏘일네일링 공법은 절취사면 보강이나 도심지 터파기 및 흙막이 구조물, 옹벽 보강 등 사면안정에 많이 시용된다. 하지만 압력식 쏘일네일링 공법은 그라우팅을 가압하여 주입함에 띠라 주입 시와 주입 후의 지반응력의 변화 양상에 매우 복잡하다. 따라서 압력식 쏘일네일링 공법에 의한 인발저항력의 증가양상을 파악하기가 매우 어렵기 때문에 대부분 경험적인 설계가 이루어 지고 있는 실정이다. 본 연구는 압력식 쏘일네일링 공법의 인발저항력의 증가를 이론적으로 규명하고 실내 및 현장 시힘을 바탕으로 비교하여 인발저항력을 예측히는데 그 목적이 있다. 본 논문에서는 인발저항력의 증가에 영향을 미치는 요소를 공벽에 작용히는 평균연직응력과 인발마찰계수의 증가로 규명하였다. 실내시험을 통해서 측정된 반경방향 변위를 본 논문에서 제안한 공팽창이론에 적용하여 팽창각을 산정하였다. 팽창각이 감소함에 따라 반경방향변위는 증가하고 주입압이 증가함에 따라 팽창각이 증가하는 것을 알 수 있었다. 또한 현장인발시험을 통해서 측정한 인발저항력이 제안된 인발저항력과 거의 통일한 것을 알 수 있었다.
보강토 옹벽에 체인을 보강재로 사용한 경우의 인발저항력 평가를 위한 현장실험을 실시하였다. 실험에서는 횡방향 부재로 강봉이나 L-형 강재앵글을 고려하였으며, 체인의 길이(20m, 2.5m 그리고 3.0m), 보강재의 조합(체인단독, 체인+강봉 그리고 체인+앵글) 그리고 설치위치 등을 다르게 하여 총 80개소에 대해서 인발실험을 실시하였다. 체인 또는 체인+강봉의 경우, 최대 변위는 평균 150mm였으며, 인발하중은 지속적으로 증가하다가 체인의 극한강도에 도달하면 파단(인장파괴)되는 것으로 나타났다. 그러나 체인에 L-형 앵글을 조합한 경우에는 최대변위가 평균 100mm정도로서 변위 억제에 큰 효과가 있는 것으로 나타났다. 현장에서 측정된 항복 인발하중값을 이론값과 비교했을 때는 보강 방법 또는 연직응력에 따라서 현장 측정값이 이론값 보다 약 1.2~3배정도 큰 것으로 나타났으며, 체인의 길이, 연직하중의 크기, 횡방향 부재의 조합에 따라서 항복 인발하중의 크기는 변화하는 것으로 나타났다. 그러나 강봉과 L-형 앵글사이에 차이는 현저하지 않았다. 체인을 보강재로 사용하는 경우 기존의 이론식을 적용한 설계나 시공은 안전측으로 나타났으나, 체인의 인발 저항력이 너무 과소 평가되어 있다고 판단되었다.
본 연구에서는 상대밀도와 세립분 함유율이 현장타설말뚝의 인발저항 성능에 미치는 영향을 평가하기 위하여, 다양한 상대밀도 및 세립분 함유율 조건에 대한 직접전단시험 및 모형말뚝 인발실험을 수행하였다. 직접전단시험으로부터 세립분 함유율에 따른 내부마찰각과 점착력의 변화특성을 정량적으로 파악할 수 있었으며, 인발실험 결과에서는 말뚝의 인발저항 성능에 미치는 상대밀도와 세립분 함유율의 영향을 확인할 수 있었다. 또한, 두 실험 결과를 비교 분석한 결과, 말뚝의 인발저항 성능에 대한 지반의 내부마찰각과 점착력의 기여도는 세립분 함유율 약 13%를 전후로 하여 서로 다르게 나타남을 알 수 있었다. 따라서 현장타설말뚝 설계 시 수행되는 마찰저항 성능 평가는 지반의 세립분 함유율에 따른 강도정수($c-{\phi}$)를 고려해야 할 것으로 평가되었다.
Model tests for the ultimate pullout resistance of anchorages and investigation of failure behaviors in cohesionless soil have been conducted. The factors affecting the anchorage are mostly the geometry of the system, and soil properties of sands. The main conclusions of the experimental work were as follows. 1. The load - displacement relationship can be a form of parabolic curve for all plates. 2. The change in ultimate pullout resistance of anchor is mostly affected by embedment ratio and size of anchor, and influenced to a lesser degree by its shape. 3. Critical embedment ratio which is defined as the failure mode changes from shallow to deep mode is increased with increasing height of anchor. 4. For a constant anchor height, as the width of anchor increases the ultimate pullout resistance also increases. However, considering the efficiency of anchor for unit area, width of anchor does not appear to have any sigrnificant contribution on increasing anchor city. 5. Anchor capacity has a linear relation to sand density for any given section and the rate of change increases as the section increases. Critical depth determining the failure patterns of anchor is decreased with a decrease of sand density. 6. With increasing inclination angle, size of anchor, and decreasing embedment ratio, the ultimate pullout resistance of anchor under inclined loading is significantly decreased. 7. The ultimate pullout resistance of double anchor, a method of improving single of anchor capacity, is influenced by the center - to - center spacing adjacent anchors. It is also found that tandem and parallel anchor rigging arrangements decrease the anchor system capacity to less than twice the single anchor capacity due to anchor interference.
지반앵커의 극한인기저항흉을 구하기 위해서는 파괴면의 위치, 파괴면 위의 수직응력 및 마찰각 을 알지 않으면 안된다. 본 연구에서는 평면변형률 모형실험을 통해서, 앵커주변지반의 변형을 관찰하여 파괴면의 위치를 구하고, 앵커표면의 수직응력,전단응력을 실측하므로써 앵커표면의 응력상태를 분석했다. 그리고, 측압계수와 파괴면의 위치의 관계(파괴모-드)를 구하구 무차원 계수인 극한인발저항력계수를 이용하여 극한51기저항력의 산정식을 제안했다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.