• Steel and Composite Structures
• /
• v.20 no.2
• /
• pp.431-445
• /
• 2016

Seismic behavior of new composite structural system with a fabricated floor was studied. A two-bay and three-story structural model with the scale ratio of 1/4 was consequently designed. Based on the proposed model, multiple factors including energy dissipation capacity, stiffness degradation and deformation performance were analyzed through equivalent single degree of freedom pseudo-dynamic test with different earthquake levels. The results show that, structural integrity as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without concrete topping. It is proved that the cast-in-place floor in areas with high seismic intensity can be replaced by the prefabricated floor without pouring surface layer. The results provide a reliable theoretical basis for the seismic design of the similar structural systems in engineering application.

• Earthquakes and Structures
• /
• v.16 no.4
• /
• pp.487-499
• /
• 2019

Energy-based seismic design of structures has gradually become prominent in today's structural engineering investigations because of being more rational and reliable when it is compared to traditional force-based and displacement-based methods. Energy-based approaches have widely taken place in many previous studies and investigations and undoubtedly, they are going to play more important role in future seismic design codes, too. This paper aims to compute the maximum earthquake energy input to elastic single-degree-of-freedom (SDOF) systems for selected real ground motion records. A data set containing 100 real ground motion records which have the same site soil profiles has been selected from Pacific Earthquake Research (PEER) database. Response time history (RTH) analyses have been conducted for elastic SDOF systems having a constant damping ratio and natural periods of 0.1 s to 3.0 s. Totally 3000 RTH analyses have been performed and the maximum mass normalized earthquake input energy values for all records have been computed. Previous researchers' approaches have been compared to the results of RTH analyses and an approach which considers the pseudo-spectral velocity with Arias Intensity has been proposed. Graphs of the maximum earthquake input energy versus the maximum pseudo-spectral velocity have been obtained. The results show that there is a good agreement between the maximum input energy demands of RTH analysis and the other approaches and the maximum earthquake input energy is a relatively stable response parameter to be used for further seismic design and evaluations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1565-1570
• /
• 2003

Passive Haptic Devices have more benefit than the active in Stability. But Apart from benefits, it shows poor performance in haptic display. The author proposed the passive FME(Force Manipulability Ellipsoid) which can graphically show force generating ability of a passive haptic device. In this paper, performance indexes for the force approximation and pseudo friction cone are obtained with the passive FME and an optimized planar device with the indexes is proposed. Based on the above theory, experiment is conducted.

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.2
• /
• pp.67-75
• /
• 2000

virtual computer numerical control(VCNC) arises from the concept that one can experience pseudo-real machining with a computer-numerically-controlled(CNC) machine before actually cutting an object. To achieve accurate VCNC, it is important to determine abnormal behavior, such as chatter, before cutting. Detecting chatter requires an understanding of the dynamic cutting force model. In general, the cutting process is a closed loop system the consists of structural and cutting dynamic. Machining instability, namely chatter, results from the interaction between these two dynamics. Several previous reports have predicted stability for a single path, using a simple cutting force model without run out and penetration effects. This study considers both tool run out and penetration effects, using experimental modal analysis, to obtain predictions that are more accurate. The machining stability during a corner cut, which is a typical transient cut, was assessed from an evaluation of the cutting configurations at the corner.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.70-78
• /
• 2004

This paper presents study of efficiency of wavelet transformation for on-line chatter detection during hard fuming process. From comparison with other time series and statistical methods such as fast fourier transformation (FFT), Kurtosis and standard deviation (STD), wavelet transform is better than others in on-line chatter detection. With using wavelet function with pseudo frequency corresponding to chatter frequency, chatter could be detected more sensitively. And for both force signal from dynamometer and displacement signal from capacitance type cylindrical sensor (CCS), wavelet transform with DB2 function on level 4 could be well used for chatter detection in hard turning process.

• Earthquakes and Structures
• /
• v.15 no.6
• /
• pp.687-699
• /
• 2018

This paper investigates the pseudo-static analysis of reinforced slopes with geosynthetics under the influence of the uniform surcharge to evaluate the maximum tensile force of reinforcements. The analytical approach has basically been used to develop the new practical procedure to estimate both tensile force and its distribution in the height of the slope. The base of developed relationships has been adapted from the conventional horizontal slice method. The limit equilibrium framework and the assumptions of log-spiral failure surface have directly been used for proposed analytical approach. A new analytical approach considering a single layer of non-cohesion soil and the influence of uniform surcharge has been extracted from the 5n equation and 5n unknown parameters. Results of the proposed method illustrated that the location of the surcharge, amount of internal friction and the seismic coefficient have the remarkable effect on the tensile force of reinforcement and might be 2 times increasing on it. Furthermore, outcomes show that the amount of tensile force has directly until 2 times related to the amount of slope angle and its height range. Likewise, it is observed that the highest value of the tensile force in case of slope degree more than 60-degree is observed on the lower layers. While in case of less degree the highest amount of tensile force has been reported on the middle layers and extremely depended to the seismic coefficient. Hence, it has been shown that the tensile force has increased more than 6 times compared with the static condition. The obtained results of the developed procedure were compared with the outcomes of the previous research. A good agreement has been illustrated between the amount results of developed relationships and outcomes of previous research. Maximum 20 and 25 percent difference have been reported in cases of static and seismic condition respectively.

• Structural Engineering and Mechanics
• /
• v.14 no.2
• /
• pp.151-170
• /
• 2002

Moving force identification is a very important inverse problem in structural dynamics. Most of the identification methods are eventually converted to a linear algebraic equation set. Different ways to solve the equation set may lead to solutions with completely different levels of accuracy. Based on the measured bending moment responses of the bridge made in laboratory, this paper presented the time domain method (TDM) and frequency-time domain method (FTDM) for identifying the two moving wheel loads of a vehicle moving across a bridge. Directly calculating pseudo-inverse (PI) matrix and using the singular value decomposition (SVD) technique are adopted as means for solving the over-determined system equation in the TDM and FTDM. The effects of bridge and vehicle parameters on the TDM and FTDM are also investigated. Assessment results show that the SVD technique can effectively improve identification accuracy when using the TDM and FTDM, particularly in the case of the FTDM. This improved accuracy makes the TDM and FTDM more feasible and acceptable as methods for moving force identification.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.152-155
• /
• 2008

The blood flow characteristics have been closely related to various cardiovascular diseases, it is very important to predict them accurate enough in an efficient way. Thus, this paper proposes a one-dimensional spectral element model for the blood flow through blood vessels. The spectral element model is formulated by using the variational method. The nonlinear terms in spectral element model are all treated as the pseudo-force and an iterative solution method is applied in the frequency domain.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.637-642
• /
• 2013

In this paper, an analysis results of towing force and towing points which are dominating factors to determine the behavior of towed ship are introduced. The towing force and towing points to achive the desired posture and its position of the towed vessel are derived based on simplified dynamics and linearization method. LQR algorithm for posture control is applied to linearized system and numerical simulation is also executed. Force based on COG(cneter of gravity) and gain of controller to achieve desired posture for target vessel are obtained by using Riccati matrix equation and pseudo inverse matrix is applied to analyze the relation between the derived force and its towing point. Based on this analysis method, towing force need to move the towed vessel from its initial position to target position can be calculated. The towing method including towing point and direction is also considered on this method. Finally, the relation between towing force and towing point is confirmed from the analysis and the results can be applied to arrangement of tug boats during salvage works.

• Earthquakes and Structures
• /
• v.3 no.2
• /
• pp.97-115
• /
• 2012

The energy-transmitting boundary, which is used in the well-known finite element method (FEM) program FLUSH, is quite efficient for the earthquake response analysis of buildings considering soil-structure interaction. However, it is applicable only in the frequency domain. The author proposed methods for transforming frequency dependent impedance into the time domain, and studied the time domain transform of the boundary. In this paper, first, the estimation methods for both the halfspace condition under the bottom of the soil model and the pseudo three-dimensional effect were studied with the time domain transmitting boundary. Next, response behavior when using the boundary was studied in detail using a practical soil and building model. The response accuracy was compared with those using viscous boundary, and the boundary that considers the excavation force. Through these studies, the accuracy and efficiency of the proposed time domain transmitting boundary were confirmed.