• 한국군사과학기술학회지
• /
• 제14권6호
• /
• pp.1151-1158
• /
• 2011

Proximity magnetic sensor is able to detect the object target accurately in close range and it has been widely used in the underwater guided weapon system because there is no countermeasures from the target. In order to increase the damage of target by shock wave due to explosion of the underwater guided weapon system, the maximum detection range of the proximity magnetic sensor needs to be increased. In this paper, we describe the techniques of the optimum transmitting and receiving coils design using the Finite Element Method for the output power enhancement of the transmitter and the sensitivity improvement of the receiver. Finally, the proposed design techniques of the transmitter and the receiver were verified using a experimental setup and a prototype.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.971-975
• /
• 2005

In this study, a car-door-controlled collision protection system using proximity sensor is proposed and its preliminary analysis and several preliminary experiments are conducted. The proposed system has three additional sub-components on the car-door that is, a pair of extra electro-magnetic actuator that are attached to the sliding bar of the open/close car-door four-bar mechanism, a proximity sensor that would be attached to the outside surface of the door which is likely to frequently contact to the object and a driving control circuit of the whole system. A proximity sensor is used to detect object close to the car-door, the driving control circuit provides actuating power command to the electro-magnets to generate braking force to stop the swing motion of the car-door. It is verified through kinematic analysis of the four-bar car-door open/close mechanism and through experiments that the magnitude of maximum electronic magnetic force could provide the braking force enough for this application. For this purpose, an electro-magnet driving circuit is implemented and tested. And also to increase the safety of the system a time delay circuit is implemented and tested.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2007년도 추계종합학술대회
• /
• pp.231-234
• /
• 2007

자기적 원리를 이용한 Magnetic Sensor는 자기를 전기로 변환하는 Element로서 산업분야, 대학 및 연구소 등에서 대단히 폭 넓게 사용되고 있으나 아직 국내에서 체계적으로 양산 되고 있지 않은 상태이고 제작기술 수준 역시 선진국에 비해 저조하며 Excitation Current, Excitation Frequency, 코어의 투자율 등의 변화에 의해 센서 출력에 왜곡현상이 나타나거나 부하현상이 발생하여 이 때문에 최소 측정 범위가 제한된다. 따라서 양호한 출력신호를 감지하기 위해서는 신호변환장치 의 성능이 뒷받침되어야 한다. 본 논문 에서는 유도성 근접 센서를 이용 하여 신호변환장치 회로를 설계하여 금속표면에 페인트 두께를 마이크로 단위로 검출, 측정 하는 제어 시스템을 연구하는데 그 목적을 둔다.

• Interaction and multiscale mechanics
• /
• 제3권3호
• /
• pp.257-266
• /
• 2010

A novel resonance based proximity DC current sensor is proposed. The sensor consists of a piezo sensed and actuated cantilever beam with a permanent magnet mounted at its free end. When the sensor is placed in proximity to a wire carrying DC current, resonant frequency of the beam changes with change in current. This change in resonant frequency is used to determine the current through the wire. The structure is simulated in micro and meso scale using COMSOL Multi physics software and the sensor is found to be linear with good sensitivity.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1998년도 추계학술대회
• /
• pp.245-246
• /
• 1998

AMB(Active Magnetic Bearing) systems are popularly used in various areas. In biomedical engineering applications it is a key part of magnetically suspended rotary blood pumps. The special advantage of AMBs is that they enable the rotor to revolve with no physical contact and provide rotary blood pumps with better performances such as low hemolysis level. Fundamentally, AMB systems consist of three parts, proximity sensors for distance detection, microprocessor for control algorithm and power amplifiers for actuating electromagnets. We have developed an inductive type proximity sensor with satisfactory characteristics that can be used in AMB systems. Frequency response was flat at least up to 10 kHz and sensitivity, resolution$(>5{\mu}m)$ and sensing range(<5mm) of the sensor could be adjustable for various purposes. The characteristics of the completed model showed to have satisfactory behaviors compared with the commercially available ones that already appeared to have reliable behaviors in AMB systems.

• 한국전기전자재료학회논문지
• /
• 제30권4호
• /
• pp.253-257
• /
• 2017

Nowadays, it is increasingly important to detect whether cables are live for the operator's safety if there is a sudden power failure. It is especially hard to detect the electrical field of an underground line because of shielding. This paper on detection of live-line states in cables studied the detection characteristics of the change in the magnetic field and axis as the frequency, voltage, and distance at the same load are changed using 3 axes. A search coil type was used as a magnetic field sensor with non-contact. We found that magnetic fields decrease proportionally to the square of the distance and the decrease of rated voltage with load effected to magnetic field. The magnetic field was detected by 3-axis sensors given correct proximity, but appeared as noise components beyond a distance of 2 cm.

• Journal of Multimedia Information System
• /
• 제2권2호
• /
• pp.233-240
• /
• 2015

Mobile devices are becoming increasingly sophisticated and the latest generation of smartphones now incorporates many diverse and powerful sensors. These sensors include acceleration sensor, magnetic field sensor, light sensor, proximity sensor, gyroscope sensor, pressure sensor, rotation vector sensor, gravity sensor and orientation sensor. The availability of these sensors in mass-marketed communication devices creates exciting new opportunities for data mining and data mining applications. In this paper, we describe and evaluate a system that uses phone-based accelerometers to perform activity recognition, a task which involves identifying the physical activity that a user is performing. To implement our system, we collected labeled accelerometer data from 10 users as they performed daily activities such as "phone detached", "idle", "walking", "running", and "jumping", and then aggregated this time series data into examples that summarize the user activity 5-minute intervals. We then used the resulting training data to induce a predictive model for activity recognition. This work is significant because the activity recognition model permits us to gain useful knowledge about the habits of millions of users-just by having them carry cell phones in their pockets.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(5)
• /
• pp.119-122
• /
• 2001

This paper deals with new type of active magnetic bearing (AMB) for the linear motors. We adopted optical sensing mechanism for the gap sensing. Using the laser and the PSD (Position Sensitive Device), the absolute rotor position is obtained independent of the profile of the guide rail. With this measurement, the rotor can be controller to follow the straight beam of the laser. Another advantage of optical sensing mechanism might be the elimination of the possible interference between the proximity sensor and the electro-magnet. By adopting the push-full actuating mechanism, the bearing stiffness is increased near the equilibrium position. For the simplicity, distributed control system is constructed. Eight independent PID control algorithm is used with the full order observer. Several simulation md test results are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.121.4-121
• /
• 2001

We propose an off-line methodology for detecting a faulty backup roll that generates eccentricity components, under the condition that the feeding velocity, equivalently the angular velocity of roll, is not constant. From a newly devised speed angle conversion algorithm, we transform all process data into those of a virtual process under a constant feeding speed. This indirectly way, we can apply a spectral analysis to the original process. In addition, we develop an online detection method of roll eccentricity based on newly designed PLG sensor. This PLG sensor is robust because of applying magnetic proximity sensnors and non-contact measurement method.

• 한국정보통신학회논문지
• /
• 제23권9호
• /
• pp.1131-1138
• /
• 2019

부품 또는 제품들의 정전기 방지와 내마모성 및 내부식성 향상, 미각화 등 다양한 목적으로 코팅의 중요성이 증가되고 있다. 코팅막의 두께를 측정하는 방법으로 주로 프로브(probe)로 코팅면을 측정하는 접촉식 측정방식이 이용되는데, 코어의 투자율 변화에 의해 센서 출력 왜곡이나 부하 현상이 발생하여 정확도가 떨어지는 문제점이 있다. 본 논문에서는 비선형적인 특성에 의해 발생할 수 있는 문제점을 최적화된 회로설계와 두께측정 알고리즘을 적용하여 코팅막의 측정 오차를 줄이는 방법을 제안한다. 여러 코팅 샘플을 통한 실험 결과 ${\pm}2%$ 이내의 측정 정확도를 갖는 것을 확인할 수 있다.