• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.89-95
• /
• 2005

Thrust cut off(TCO) system is installed at the port of a rocket motor case forward dome. The snap ring and the closure are escaped sequentially by pulling out a wedge under internal pressure. The hydraulic structural tests of TCO and numerical simulations were performed, and both results were compared to understand the deformation behavior of TCO. By increasing splines symmetrically, the sealing capacity of TCO can be improved significantly. The escape pressure of TCO increases according to the increase of friction coefficient and there is a critical friction coefficient beyond which the snap ring can not be nearly escaped even after forced escape of wedge. Under low friction coefficient the snap ring is contracted to radial direction and easily escaped. But, under high friction coefficient, the snap ring can not be escaped from the port even after severe plastic deformation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.2
• /
• pp.91-102
• /
• 1997

In order to evaluate the effects of aging on the ignition performance, pyrotechnic igniters were separated from twelve-year-old, fifteen-year-old, and sixteen-year-old live rocket motors. The characteristic values of the ignition material were measured, and the firing tests of the igniters were performed. The moisture content, the outer dimension, the crush strength, the thermal decomposition characteristics, and the heat of formation the B/$KNO_3$ ignition pellet were measured. The crush strength was increased and the heat of formation was reduced as aged, but no change was detected for other characteristic values. The burning test results of the igniter pellet in the closed bomb and the inert motor showed that the burning rate of the ignition pellet was increased by 10%, and the integration of pressure $P_t$ of the p-t curve was reduced by 15% for aged samples. It was inferred that the burning rate was increased as the crack was appeared in the pellet and $P_t$ could be proportionally decreased with the heat of explosion.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.2
• /
• pp.26-36
• /
• 2007

The thermal response characteristics of nozzle liner for a solid rocket motor applying highly aluminized PCP or HTPB propellant with slotted tube grain have been investigated. The SEM photographs of aluminum oxide particles taken from nozzle liner show that the PCP propellant with the finer and less contents of oxidizer can offer greater possibility for increasing aluminum agglomeration than the HTPB propellant. The PCP propellant shows locally greater mechanical erosion at 4 circumferential areas of the nozzle entrance in line with grain slot due to the impingement of large particles, but the HTPB propellant shows greater thermochemical ablation at the nozzle blast tube, the throat insert and the exit cone because of relatively much more mole fraction of $H_2O\;and\;CO_2$ in combustion gases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.4
• /
• pp.33-42
• /
• 2014

Flame behaviors and interaction between pilot and main flames in a dual swirl combustor were investigated experimentally and numerically. Under the condition of fixed swirl angle of $45^{\circ}$ for main flame, the swirl angle of pilot flame, total heat release rate and equivalence ratio of main flame were used as major parameters. As a result, detailed flame stability diagram of dual swirl combustor was identified in terms of 5 flame modes with the changes in total heat release rate and equivalence ratio of main flame. It was found that the swirl angle of pilot flame plays the most important role in the changes in flame location and overall flow structure inside the combustor, and thus leads to the significant change in the interaction between pilot and main flame.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.820-824
• /
• 2010

The purpose of this study is to develop basic technology of hybrid rocket vehicle by constructed and launched. This small hybrid rocket using HDPE/LN2O and Aluminium steel for its body (weight : 12.5 kg, diameter : 114 mm, height : 1.8 m) was designed. The fuel grain and injector were designed for 50 kgf thrust and burning time 2.5 sec. This rocket was loaded the data acquisition device for obtaining data of pressure and velocity during its flying and equiped an automatic ejector system using spring/motor and timer to collect the rocket more safely after launching. It was launched successfully, but found some problem that the rocket's weight was heavier than expected and the thrust was not enough to reach the designed altitude and analyzed its flight path way.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.27-33
• /
• 2014

2nd stage of KSLV-I, NaRo-Ho, performs CCAM not to collide with Naro Science Satellite. At that moment, the satellite should pass through the Plume Density area which was generated by KSLV-I KM residual thrust. Therefore, it is necessary to predict Plume Density field of KM residual thrust and guarantee the safety of the trajectory of payload. In this paper, DSMC method was used to simulate Plume Density by KM residual thrust and the simulation showed that the trajectory of Naro Science Satellite was safe.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.2
• /
• pp.29-38
• /
• 2010

The experimental study on paraffin wax/LDPE blended fuel for hybrid rocket was performed. Various combustion characteristics of blended fuel were compared with pure paraffin, HTPB, HDPE and SP-1a fuel in order to evaluate the performance of blended fuel. The regression rate of lab-scale and large-scale motor using pure paraffin fuel was increased by 10.2 and 9.8 factor when respectively compared to that of HDPE. The regression rate factor of blended fuel was 3.4 in which the regression rate of blended fuel was higher than that of HTPB and HDPE, but lower than that of pure paraffin, SP-1a fuel. The values of characteristic velocity and specific impulse of blended fuel was higher than those of pure paraffin, HTPB and HDPE, and almost the same as SP-1a fuel. As these results, it was confirmed that blended fuel can be an effective solid fuel for hybrid rocket.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.210-213
• /
• 2010

Recent experimental data shows that the noticeable feature of irregular roughened spots on the fuel surface occurs during the combustion test. The generation of these unexpected patterns is likely to be resulted from the disturbed boundary layer due caused by wall blowing which is intended to simulate the process of fuel vaporization. LES without chemical reaction was conducted to investigate the flow characteristics at the near-fuel surface and the behavior of turbulent structures which is evolved by the wall blowing at the Reynolds number of 23,000. Cylindrical geometry was considered to get the most reality of the calculation results because real hybrid rocket motor is circular grain configuration. It was shown that the wall blowing pushed turbulent structures upwards making them tilted and this skewed displacement, in effect, left the foot prints of the structures on the surface. This change of kinematics may explain the formation of irregular isolated spots on the fuel surface observed in the experiment.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.560-562
• /
• 2017

This paper presents the development and test results of a test rig for confirming the hover performance of the coaxial propeller which is applied to the drone in order to carry out the mission that requires high payload such as the development of the courier drones. the performance of each propeller was measured by varying the thrust and torque according to the H/D ratio. the Thrust sensor and torque sensor were used to measure the thrust and torque generated when the propeller rotated, and a photo sensor was used to measure the rpm. it used the data acquisition system to acquire data from each sensor, and used the Labview softwaer to control data storage, monitoring and BLDC motor control. In the test, each propeller meansured the figure of mefit according to the chansge of the interval at the same rpm.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.933-935
• /
• 2017

This paper deals with the influence of fungi for the thermal protective cork-based exterior insulator which protect a missile system from aerodynamic loads and heating during flight of missile. We consider the adhesion of cork-based composite on the composite motor case which fabricated by filament winding process. We also consider the importance of the requirement analysis for effective, successful system development under given system conditions. In order to develop the basic requirement analysis for the thermal protective cork-based exterior insulator, an experimental requirement analysis was accomplished, and some experimental comparing results, the study for preventing fungi are presented.