• Journal of Advanced Marine Engineering and Technology
• /
• 제9권2호
• /
• pp.159-169
• /
• 1985

The calculation of torsional vibration for marine diesel engine propulsion shafting is normally carried out by equalizing exciting energy to damping energy, or using the dynamic magnifier. But, with these methods, the vibration amplitudes are calculated only for resonance points and vibration amplitudes of other running speeds of engine are determined by the estimation. Recently, many energy-saving ships have been built and on these ships, two-stroke, supercharged, super-long stroke diesel engines which have a small number of cylinders are usually installed. In these cases, the first order critical-torsional vibrations of these engine shaftings appear ordinarily near the MCR speed and the stress amplitudes of their vibration skirts exceed the limit stress defined by the rules of classification society. To predict the above condition in the design stage, the synthesized vibration amplitudes of all orders which are summed up according to their phase angles must be calculated from the drawings of propulsion shaft systems. In this study, a theoretical method to fulfill the above calculation is derived and a computer program is developed according to the derived method. And a shafting system of two-stroke, super-long stroke diesel engine which was installed in a bulk carrier is analyzed with this method. The measured values of this engine shafting are compared with those of calculated results and they show a fairly good agreement.

• Journal of Advanced Marine Engineering and Technology
• /
• 제11권2호
• /
• pp.51-60
• /
• 1987

Recently, the problem of the axial vibration for the marine diesel engine shafting has become important due to the increased exciting forces resulting from high supercharging and large output, and the reduced natural frequencies resulting from long stroke and show speed. The effects of the axial vibration on the propulsion shafting induce cracks of the connecting point of crankpin and crankarm, the severe wear of thrust bearing, the fatigue failure of each fixing bolt and jointed parts, the hull and local hull vibrations, and also the wear and the noise due to intense hammering phenomena of thrust collar. Therefore, each classification society requires the calculation of natural frequencies and their amplitudes and also measurements of the forced damped axial vibration. At present, the technical and theoretical level is at the stage of estimating the resonant points and their maximum displacements, but the estimated displacements of the resonant points are not so reliable as the torsional one. In this study, induced stresses and amplitudes of the forced damped axial vibration are calculated. For this purpose, the equation of forced axial vibration with damping for the propulsion shafting is derived and its steady-state response is calculated by the mechanical impedance method. A computer program for above calculations is developed. The measured values are analyzed and the calculated results are compared with the measured ones. They show fairly good agreements and the reliability of developed program is confirmed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.482-492
• /
• 2004

Recently. the market trend for marine diesel engine has involved the lower running speeds. larger stroke/bore ratio and higher combustion pressure. Consequently, because of the flexible engine shafting system due to the larger mass. inertia and the more elasticity, the complicated coupled torsional-axial vibrations have occurred in the operating speed range. Also, the vibrations act as an excitation on the hull-structural vibration. To predict the vibration behavior with more accuracy and reliability. many studies have proposed the several kinds of method to calculate the stiffness matrix of crankshaft. However, most of these methods have a weak point to spend much time on three dimensional modeling and meshing work for crankshaft. Therefore. in this work. the stiffness matrix for the crankthrow is calculated using the energy method (Influence Coefficient Method, ICM) with the each mass having 6 degree of freedom. Its effectiveness is verified through the comparison with the stiffness matrix obtained by using the finite element method (FEM) and measured results for actual ships propulsion system.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 추계학술대회 논문집(Proceeding of the KOSME 2000 Autumn Annual Meeting)
• /
• pp.99-107
• /
• 2000

With the results of calculation for natural frequencies, the forced reponses of coupled vibration of propulsion shafting were analysed by the modal analysis method. For the forced response analysis, axial exciting forces, axial damper/detuner, propeller exciting forces and damping coefficients were extensively investigated. As the conclusion of this study, some items are cleared as next. - The torsional amplitudes are not influenced by the radial excitation forces. - The axial vibrational amplitudes are influenced by the tangential exciting forces. An increase of amplitude is observed for the speed range in the neighbourhood of any torsional critical speed. - The coupling effect becomes larger if torsional and axial critical speed are closer together. - The axial exciting force of propeller is relatively strong, comparing with those of axial forces of cylinder gas pressure and oscillating inertia of reciprocating mechanism. Therefore, as a resume one can say, that- Torsional vibration calculation with the classical one dimension model is still valid. - The influence of torsional excitation at each crank upon the axial vibration is impotent, especially in the neighbourhood of a torsional critical speed. That means that the calculation of axial vibration with the classical one dimension model is insufficient in most of cases. - The torsional exciting torque of propeller can be neglected in most of cases. But, the axial exciting forces of propeller can not be neglected for calculating axial vibration of propulsion shafting.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권2호
• /
• pp.171-173
• /
• 2003

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권2호
• /
• pp.198-208
• /
• 2003

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권2호
• /
• pp.209-217
• /
• 2003

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권3호
• /
• pp.356-364
• /
• 2003

• 대한조선학회논문집
• /
• 제31권4호
• /
• pp.157-166
• /
• 1994

최근의 배는 에너지절약을 도모하기 위하여 디이젤기관이 대구경 장행정 소수실린더 저속회전화 추세에 있기 때문에 기진력이 커지고 있다. 이와같은 결과로 추진축계에 과잉비틂진동응력이 작용하게 되어 선박운항에 지장을 줄 정도의 플로렐러축의 결손사고가 종종 발생하곤 한다. 현재까지의 추지축계에 대한 설계 및 비틂진동해석은 대부분 축계의 비틂기진력이 확정적이란 가정하에 수행되어 왔다. 이와 관련하여 축계 비틂기진력의 불규칙성의 영향을 고려한 확률적 비틂진동해석에 관한 연구가 이루워지고 있다. 본 연구에서는 기관기진력의 확률변수를 고려하여 추진축계의 강제 비틂진동의 확률적 해석에 대한 새로운 방법을 제시하였다. 확률적 해석에 응답면이론과 Monte Carlo 시뮤레이션 방법이 이용되었다. 본 해석방법의 타당성 여부를 확인하기 위하여 Nikolaidis 등이 사용한 시산대상선에 대한 일련의 수치계산을 수행하고, 그 결과를 Nikolaidis 등의 연구결과와 비교 검토하여 본 결과 비교적 잘 일치하고 있음을 미루어 보아 본 해석방법이 타당성이 확인되었다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 춘계학술대회 논문집(Proceeding of the KOSME 2000 Spring Annual Meeting)
• /
• pp.60-71
• /
• 2000

When the crankshaft of Diesel engine has more than 3 throws which are arranged in a different plane its vibration induces coupled motions especially the coupled torsional and axial vibration. Nowadays the torsional vibration which is influenced rather weak than axial one can be theoretically calculated fairly accurately but theoretical calculation results of the axial vibration which is influenced strongly from torsional vibration is not so good. To get accurate calculation results of axial vibration coupled axial-torsional vibration must be treated. in this investigation coupled effects of vibration of Diesel engine propulsion shafting are analyzed theoretically and some more simple calculation methods are also studied. On this first report effects of coupling on natural frequencies and their modes are mainly studied setting the each mass in 4 degrees of freedom. later this problem may be studied again by setting each mass as 6 degrees of freedom.