• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.268-273
• /
• 1998

Effect of aging treatment on the microstructures and mechanical properties of 6N01 Aluminium alloy was investigated by differential scanning calorimetry, transmission electron microscopy, microhardness measurement and tensile test. It was found that the precipitation sequence of 6N01 Aluminium alloy was GP zone ${\rightarrow}$ metastable hexagonal $Mg_2S_i({\beta}^{\prime})$,${\rightarrow}$ equilibrium fcc $Mg_2S_i({\beta})$, and the precipitates at peak aged condition were GP zones and ${\beta}^{\prime}$ phase. Microhardness changes during over aged condition showed very small decrease upon increased aging time. This result was attributed to the very slow transformation rate of ${\beta}^{\prime}$ to ${\beta}$. Maximum hardness(116 Hv) and tensile strength(312.6MPa) with 22.3% elongation were obtained from the specimen aged at $180^{\circ}C$ for 15hrs.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.59-64
• /
• 2011

Al6082-T6 is widely used because of its corrosion resistance and excellent strength. HAZ softening occurs in MIG welding process for this aluminium alloys because this aluminium alloy is heated to higher temperature than its aging temperature during welding. Therefore, low heat input and minimum standard deviation of heat input are required for narrow HAZ width and, for higher strength of welds. In this study, Al6082-T6 was used to examine for HAZ softening with various heat input in aluminium MIG welding. For weldments, micro hardness was measured and tensile test was carried out. Minimum hardness was increased at high speed welding such as 80cm/min and 120cm/min in welding speed comparing with 40cm/min. Also, in case of high speed welding such as 80cm/min and 120cm/min, tensile strength of weldments was increased about 10% comparing with low speed welding(40cm/min).

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.193-194
• /
• 2006

With the onging trend of weight saving in automobiles, the application of light alloys is increasing. Recently, aluminum powder metallurgy has been the subject of renewed attention due to the combination of lightweight of aluminium and the efficient material utilisation of the powder metallurgical process, which offer attractive benefits to potential end-users. This study is to explore the use of warm compaction process to aluminium powder metallurgy. This paper presents a detailed study of the effect of warm compression and sintering conditions on the resultant microstructures and mechanical properties of Al-Cu-Mg-Si PM blend.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.278-279
• /
• 2006

The increasing demand for automotive industries to reduce the weight of the vehicles has led to a growing usage of Al alloy powder metallurgy (P/M) parts. In order to control the sintered microstructure and mechanical properties of the aluminium alloy powder metallurgical (P/M) parts, it is essential to establish a fundamental understanding of the microstructural development during the sintering process. This paper presents a detailed study of the effect of temperature and initial starting materials on the evolution of microstructure during the sintering of Al-Cu-Mg-Si blends for PM.

• Structural Engineering and Mechanics
• /
• v.55 no.2
• /
• pp.263-280
• /
• 2015

This paper describes a study of the collision of hard steel spheres against aluminium thin circular plates at speeds up to 140 m/s. The tests were monitored by a high speed camera and a chronoscope, which allowed the determination of the ballistic limit and the plate deformation pattern. Quasi-static material parameters were obtained from tests on a universal testing machine and dynamic mechanical characterization of two aluminium alloys were conducted in a split Hopkinson pressure bar. Using a damage model, the perforation of the plates was simulated by finite element analysis. Axisymmetric, shell and solid elements were employed with various parameters of the numerical analysis being thoroughly discussed, in special, the dynamic model parameters. A good agreement between experiments and the numerical analysis was obtained.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.302-305
• /
• 2009

This paper examines the effect of nitride formation on formability for Cu bearing high strength extra low carbon (ELC) steel sheets. For this purpose, we have investigated the effect of addition of aluminium (Al) and boron (B) on texture and precipitation behavior of the ELC steel during continuous annealing. Mechanical properties and microstructures of the ELC steel sheets were analyzed as well using uni-axial tensile test, electron back-scattered diffraction (EBSD) technique and transmission electron microscopy (TEM) following pilot rolling and continuous annealing. It has been found that the addition of Al and B increases the precipitation of AlN and BN. What is more, the scavange of solute nitrogen is effective in increasing the formability of the ELC steels. In addition, the Al and B addition improves the aging property of the ELC steel.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.34-39
• /
• 2014

There are so many difficulties of melt bonding mainly applied for hull construction of a aluminum alloy small boat. For resolving this problem, Friction stir welding(FSW) in non-melting solid state welding Process generally is applied in the transport industry. This paper is studied the joining strength characteristics and macrostructure according to dissimilar aluminium 5000/6000 alloy joining for a small boat applied for this FSW technology. It is reported that difference of joining strength in accordance with the direction of rotation in case of friction stir welding between dissimilar metals(Al/Cu, Al/Fe) is also highly large. In this study, Test is carried out by making the specimen according to the direction of rotation of dissimilar aluminium alloy joining.

• Steel and Composite Structures
• /
• v.51 no.4
• /
• pp.407-416
• /
• 2024

The main objective of the present paper is to investigate the nonlinear vibration of buckled beams fixed at both ends and made of Aluminium allay (Al-alloy) reinforced with randomly dispersed Single Walled Carbon Nanotube (SWNT). The Mori-Tanak (M-T) micromechanical approach is selected to predict the homogenized material properties of the beams. The differential equation of motion governing the nonlinear behavior of the Euler-Bernoulli homogeneous beam is solved using an analytical method. The influences of diverse parameters including axial load, vibration amplitude, SWNT volume fraction, SWNT aspect ratio and beam slenderness ratio on the nonlinear frequency are studied.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.2
• /
• pp.64-77
• /
• 1989

In this study, the experiments were carried out for the purpose of establishment of aluminium cementation to steel surface by diffusible heat treatment after making the coated film onto the substrate by arc spray method. Also, the microstructure and mechanical properties of the cementation layer produced by this study were inspected for various heat treatment and spraying conditions. Main results obtained are as follow ; 1. The coating film characteristics which have excellent errosion-resistance, high temperature oxidation-resistance are obtained by aluminium penetration heat treatment after making the sprayed aluminum coating film onto the steel substrate. 2. Aluminium diffusion penetration takes place at higher temperature than 660.deg.C, and the more heat treatment time and the higher heat treatment temperature adopted, the deeper diffusion layer obtained. 3. Insert gas arc spraying using argon gas as the carrier gas higher improvement of mechanical property than that of compressed air environment. 4. The coating film characteristics appeared to be improvement of adhesive property, porosity plugging effect by heat treatment in air environment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.5
• /
• pp.471-478
• /
• 2010

Thin films play an important role in many technological applications including microelectronic devices, magnetic storage media, MEMS and surface coatings. It is well known that a thin film's material properties can be very different from the corresponding bulk properties and thus there has been a strong need for the development of a reliable test method to measure the mechanical properties of a thin film. We have developed an alternative and convenient test method to overcome the limitations of previous membrane deflection experiment and uniaxial tensile test by adopting a white light interferometer having sub-nanometer out-of-plane displacement resolution. The freestanding aluminium specimens are tested to verity the effectiveness of the test method developed and get the tensile properties. The specimens are 0.5 rum wide, $1{\mu}m$ thick and fabricated through MEMS processes including sputtering. 1 to 5 specimens are fabricated on Si dies. The membrane deflection experiments are carried out by using a homemade tester consisted of a motor-driven loading tip, a load cell, and 6 DOF alignment stages. The test system is compact enough to set it up beneath a commercial white light interferometric microscope. The white light fringes are utilized to align a specimen with the tester. The Young's modulus and yield point stress of the aluminium film are 62 GPa and 247 MPa, respectively.