• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.93-101
• /
• 2000

In this paper, propagation characteristics are analyzed under the Korean propagation condition based on the measurements for Ka-band beacon signal of COMET satellite which moves in non-geostationary orbit. Radio propagation characteristics varying as time, range, and elevation angle are presented also. As results, it is concluded that free space loss is a major parameter to the radio propagation characteristics varying as a range in clear sky. In addition, the effect of elevation angle is negligible because COMETS is observed above 40 degree.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.451-454
• /
• 2008

Potential tsunamis which may occur near Ryukyu Islands were simulated. Propagation characteristics of the potential tsunamis over the southwestern sea and the influence of tsunamis on the southwestern coast of Korean Peninsula were analyzed. The shallow water area in the east sea of China and the deep water Okinawa Trough play an important role in wave transformation and propagation of the potential tsunamis. The propagation characteristics of the potential tsunamis generated near Ryukyu Islands can be described as in followings : In the first stage after generation, the tsunamis propagate with high speed both northeastward and southwestward along the Okinawa Trough. As a result the waves are elongated and the tsunami height is significantly reduced. The elongated crest of tsunamis spans the whole distance of the Okinawa Trough and lines up toward the edge of the continental shelf of East China Sea. Then, the tsunamis are propagating towards the southeast coast of China. Thus, the influence of tsunamis on the Korean coasts becomes weak.

• Structural Engineering and Mechanics
• /
• v.62 no.6
• /
• pp.781-788
• /
• 2017

In this paper, a stress wave model is established to describe the three states (separate, contact and impact) of clearance joints. Based on this stress wave model, the propagation characteristics of stress wave generated in clearance joints is revealed. First, the stress wave model of clearance joints is established based on the viscoelastic theory. Then, the reflection and transmission characteristics of stress wave with different boundaries are studied, and the propagation of stress wave in viscoelastic rods is described by the characteristics method. Finally, the stress wave propagation in clearance joints with three states is analyzed to validate the proposed model and method. The results show the clearance sizes, initial axial speeds and material parameters have important influences on the stress wave propagation, and the new stress waves will generate when the clearance joint in contact and impact states, and there exist some high stress region near contact area of clearance joints when the incident waves are superposed with reflection waves, which may speed up the damage of joints.

• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.1
• /
• pp.49-63
• /
• 1984

The 5086-H116 Al-Alloy plate specimens having an edge through-thickness notch were investigated to find out the characteristics of the corner crack propagation by the plane bending fatigue. The experiments were also carried out in order to clarify the change of the corner crack propagation behaviour due to the various materials and their thicknesses. In addition, the retardation effect of overload on the corner crack propagation was quantatively studied. Main results obtained are as follows; 1. In the case of estimating the crack propagation rate of the corner crack, it is more reasonable to consider the growth rate of fracture surface area than that of crack length. 2. The shape of the corner crack growing in the plane plate under the bending fatigue can be estimated. 3. The crack propagation rate increases with the increasing of the thickness and the decreasing of the Young's modulus of materials. 4. Regardless of a thickness and kind of materials of specimen, the characteristics of the corner crack propagation can be concluded. 5. The retardation effect of overload is distinct in the corner crack propagation.

• Journal of Korean Society of Transportation
• /
• v.29 no.3
• /
• pp.123-137
• /
• 2011

In general, flow propagation has been explained using the shock wave theory which is expressed as a function of variations in volume and density. However, the theory has certain limitation in portraying heterogeneous flow, e.g., flow propagation between lanes. Motivated by this fact, this study seeks a new measure for analyzing the propagation characteristics of traffic flow at three sections of highway (i.e., merging area, weaving section, and basic section) from temporal and spatial perspectives, and then develops a model for estimating the measure for the flow propagation. The "shock wave speed" which is the measure widely adopted in literature, was first applied to describe the propagation characteristics, but it was hard to find distinct characteristics in the propagation. This finding inspires to develop a new measure named "Impulse Volume". It is shown that the measure better explains the propagation characteristics at the three study sections of highway. In addition, several models are also developed by performing multi-regression analyses to explain the flow propagation between lanes. The models proposed in this paper can be distinguished in three sections and the lane placement.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.1
• /
• pp.55-66
• /
• 2021

In this paper, we propose a signal propagation modeling technique for generating a positioning fingerprint DB based on Long Term Evolution (LTE) signals. When a DB is created based on the location-based signal information collected in an urban area, gaps in the DB due to uncollected areas occur. The spatial interpolation method for filling the gaps has limitations. In addition, the existing gap filling technique through signal propagation modeling does not reflect the signal attenuation characteristics according to directions occurring in urban areas by considering only the signal attenuation characteristics according to distance. To solve this problem, this paper proposes a Deep Neural Network (DNN)-based signal propagation functionalization technique that considers distance and direction together. To verify the performance of this technique, an experiment was conducted in Seocho-gu, Seoul. Based on the acquired signals, signal propagation characteristics were modeled for each method, and Root Mean Squared Errors (RMSE) was calculated using the verification data to perform comparative analysis. As a result, it was shown that the proposed technique is improved by about 4.284 dBm compared to the existing signal propagation model. Through this, it can be confirmed that the DNN-based signal propagation model proposed in this paper is excellent in performance, and it is expected that the positioning performance will be improved based on the fingerprint DB generated through it.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.03a
• /
• pp.265-272
• /
• 1998

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.37-46
• /
• 2016

For the SI engines, at only full load, the pumping loss has a negligible effect, while at part load conditions, the pumping loss increases. To avoid the pumping loss, the spark-ignited engines are designed to inject gasoline directly into the combustion chamber. In the spark-ignited direct-injection engines, ignition probability is important for successful combustion and the flame propagation characteristics are also different from that of pre-mixed combustion. In this paper, a visualization experiment system is designed to study the ignition probability and combustion flame characteristics of spark-ignited direct-injection CNG fuel. The visualization system is composed of a combustion chamber, fuel supply system, air supply system, electronic control system and data acquisition system. It is found that ambient pressure, ambient temperature and ambient air flow velocity are important parameters which affect the ignition probability of CNG-air mixture and flame propagation characteristics and the injected CNG fuel can be ignited directly by a spark-plug under proper ambient conditions. For all cases of successful ignition, the flame propagation images were digitally recorded with an intensified CCD camera and the flame propagation characteristics were analyzed.

• Journal of Power System Engineering
• /
• v.20 no.2
• /
• pp.32-42
• /
• 2016

Under part load condition of spark-ignition engine, pumping loss had great effect on engine efficiency. To reduce pumping loss, the study designed spark-ignited engines to make direct spray of gasoline to combustion chamber. In spark-ignited direct-injection engines, ignition probability is important for successful combustion and flame propagation characteristics are also different from pre-mixed combustion. This study designed a visualization testing device to study ignition probability of spark-ignited direct-injection LPG fuel and combustion flame characteristics. This visualization device consists of combustion chamber, fuel supply system, air supply system, electronic control system and data acquisition system. Ambient pressure, ambient temperature and ambient air flow velocity are important parameters on ignition probability of LPG-air mixture and flame propagation characteristics, and the study also found that sprayed LPG fuel can be directly ignited by spark-plug under proper ambient conditions. To all successful cases of ignition, the study recorded flame propagation image in digital method through ICCD camera and its flame propagation characteristics were analyzed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.836-842
• /
• 2001

The more sophisticated patterns of propagation model is presented in this paper, which includes three different source characteristics. The spherical, cosine and dipole radiation characteristics compared and sound event level and the maximum sound level are calculated by experiment and calculation. It is shown that patterns of propagation has dipole characteristics for low speed range(below about 150km/h) at electric multiple system. We know that push-pull high speed system(maximum speed: 300km/h) has cosine characteristics of noise propagation. For this purpose, We conduct the experiment of noise and know the empirical formula of noise level and radiation coefficient K. This model of simulation is conducted through point source array model at wheel/rail contact point by using program and experimental formula. We can guess prediction of profile, flat and wear of wheel by above modeling in near field.