• Journal of Korean Society of Steel Construction
• /
• v.9 no.2 s.31
• /
• pp.237-248
• /
• 1997

Three types of fatigue cracks frequently observed in the crane runway girders are verified experimentally using two testing-purpose girders with the size of $6400{\times}600{\times}300$ in millimeters. The fatigue cracks are observed in the vicinity of load-bearing points, at the end of gusset plates and at the fillet welded joints between the lower flange and the web. The load-bearing-point cracks are initiated at the intersection of the fillet welds between the upper flange and the web, where the vertical stiffener is located. The cracks grow up toward the diagonal direction of the web. The cracks observed at the fillet welded joints grow up perpendicularly to the crane runway girder. Compared with the JSSC fatigue design code, the joint class is classified as follows: E for the vicinity of load-bearing points, G or H for the end of gusset plates and D for the lower fillet welded joints. The tests reveal that the class of joint classification at the end of gusset plates and at the lower flange coincides with the fatigue design code.

• Journal of Satellite, Information and Communications
• /
• v.11 no.3
• /
• pp.133-137
• /
• 2016

Millimeter wave wireless communication systems, especially those targeting indoor high rate data transfer, have a strong requirement for high quality wireless link. Unfortunately, in this frequency band, the electromagnetic wave has to sustain the high propagation loss caused by the smaller wavelengths. In this scenario, beamforming technique, which enhances the link quality by focusing the radiation power on a direction, becomes one of the most important techniques in millimeter wave band wireless communication. In recent year, there been conducted many research on beamforming to improve the performance of wireless system. In this paper, we evaluate the performance of a simplified codebook-based beamforming scheme which is based on multiple-procedure and three-state beam selection. The simplified scheme significantly reduces beamforming setup time, comparing to the exhaustive searching, two-level searching adopted in IEEE 802.15.3c standard, and also conventional multi-level scheme.

• 연구논문집
• /
• s.23
• /
• pp.127-140
• /
• 1993

The drive pulley, which is employed for loading and unloading raw materials in a steel mill, is usually manufactured by use of various welding processes. In this study the weldment in the pulley, in which TIG and $CO_2$ welding processes are used, has been analyzed from view point of fracture mechanics. Fracture toughness tests have been performed according to ASTM E813. A servo-hydraulic testing machine (10kN) has been employed. Also the crack propagation tests (Mode I) have been performed with compact tension specimen in compliance with ASTM E647. To predict the critical crack size in the weldment, finite element stress analysis for the drive pulley under real operating conditions have been performed. In addition, the residual stresses at the weldment and in heat-affected zone have been obtained by hole drilling method. The planar critical crack size have been predicted for the drive pulley by considering the stress analysis results and the residual stresses due to welding process. For the drive pulley considered in this study, it has been concluded that the most important factor in determining the critical crack size is the welding residual stress in the transverse direction. Also the effect of stress concentration at the root of the weldment have been noticeable. For the planar crack, the fatigue crack growth life from an initial crack size of 2mm to the critical crack size obtained as in the above have been predicted. The predicted lives were between 55, 900 and 72, 000 cycles depending on the shape of the elliptical crack. The predicted lives were in fairly good agreement for the drive pulley considered in this study.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.12
• /
• pp.1307-1313
• /
• 2014

In this paper, we have proposed a tapered slot antenna for IR-UWB communication system suitable of indoor positioning in the building. The designed tapered slot antenna is designed using Ansys Inc. HFSS and its standing wave ratio, return loss, and radiation pattern is analyzed. In 2.36 GHz ~ 5.51 GHz and, the designed antenna shows satisfactory return loss at -10 dB and meets the requirement of $VSWR{\leq}2$. The presented designed showed a higher sensitivity for the end-fire propagation characteristics in a specific direction across all bands of the radiation pattern.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.7
• /
• pp.65-73
• /
• 2020

Viral video advertising is being used in the advertising and film industry for pre-promotion of certain products or pre-release films which has a lot of effect on investment. An analysis of viral video recognition is needed to predict future development directions. In response, the study conducted a survey on viral videos, focusing on college students in their 20s, who are the most exposed to advertisements and movies. Through this, the survey was conducted on recognition of viral videos, memorable viral videos, satisfaction level, message propagation method, positiveness of viral videos, expected future development, and desired viral video type. The survey showed that viral video recognition was 16.7% and the most memorable viral video; the "Let it Go" viral video from the movie "Frozen" was 69.1 %, according to the survey. The satisfaction level was not high at 31.2 %, and 73.5% of people sent messages to others after watching viral videos, which was very high. Negative opinions on viral videos were low at 13.7 %. 64.5% of the surveyors said the future of the viral videos would "develop" and 6.7% said would "not develop."

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.922-933
• /
• 2002

Since the deterioration of concrete bridge decks affect durability, safety, and function, structural rehabilitation of damaged concrete deck that was strengthened with Fiber Reinforced Polymer(FRP) is increasing the latest. But recent studies on the strengthened structures are focused on the static behavior, however only a few studies on the fatigue behavior are performed. In this study, static and fatigue behavior of strengthened deck were peformed on 11 deck specimens strengthened with sheet typed Glass Fiber Reinforced Polymer(GFRP) that were reinforced by two different strengthening methods for the static test. A amount of strengthening material in the each direction such as transverse and longitudinal was adopted experimental variables for the static test and also the stress level of the static maximum load are adopted for the fatigue test. By the results of the experimental study, with respect to the strengthened decks, the resistance effect of crack propagation and effect of stress distribution are improved. In addition, the rate of variation of compliance decreased.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.339-347
• /
• 2014

In this paper, the authors present a new design for a broad-band metamaterial(MTM) absorber that utilizes flexible substrate. The proposed MTM unit cell is constructed by a electric-inducive-capacitive(ELC) resonator and a cut-wire on the same side of the flexible polyimide substrate. To reduce the radar cross section at frequencies other than the targeted frequency bands, the metallic pattern layer of the proposed structure is placed facing toward the incident wave propagation direction. A prototype absorber was fabricated with a planar array of $33{\times}45$ unit cells. Our experiments showed that the proposed absorber exhibits a peak absorption rate of 92 % and 93 % at 9.06 GHz and 15.0 GHz, respectively, and 75 % of the full-width at half-maximum(FWHM) bandwidth is achieved. The proposed backplane-less MTM structure can be used for a broad-band microwave absorber and irregular surface applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3277-3285
• /
• 1996

In this paper, w designed an opical power distribution device for application to an optical switching and an optical subscriber loop. We fabricated PSG thin film by LPCVD. Based on the measured index of fabricted thin film, rib-type waveguide was transformed to two-dimension by the effective index method and we simulated dispersion property to find asingle-mode condition. We found that the optimum design parameters of rib-type waveguide are:cladding layer of 3.mu.m, core layer of 3.mu.m, buffer layer of 10.mu.m, and core width of 4.mu.m. Each side of the guiding region was etched down to 4.mu.m to shape the core. We used these optimum parameters of the rib-type waveguide with branching angle of 0.5.deg. and simulted the Y-branch waveguide by the BPM simulation. Numerical loss in branching area was claculated to be 0.1581dB and equal to the total loss of the Y-branch. The loss of the fabricated Y-branch waveguide on PSG film ws 1.6dB at .lambda.=1.3.mu.m before annealing but was 1.2dB after annealing at 1000.deg. C for 10 minutes. Consequently, the loss of branching area from 3000.mu.m to 6000.mu.m in the z-direction was 0.8dB, and single-mode propagation was confirmed by measuring the near field pattern. For coupling the fabricated Y-branch waveguide with an optical fiber, we fabricated V-groove which was used as the upholder of optical fiber. An etching angle was 54.deg. and the width and depth of guiding groove was 150.mu.m, 70.mu.m, respectively. The optical fiber is inserted onto V-groove. Both the Y-branch and V-groove were connected through the index matching oil. Coupling loss after connecting Y-branch and the optical fiber on V-groove was 0.34dB and that after injecting index mateching oil was 0.14dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.228-234
• /
• 2005

A magnetic composite as noise absorber of quasi-microwave band was developed. The Fe-Si-Al alloy powder were forged by attrition mill to get flaky shape. The magnetic composite sheet was fabricated in which powders are dispersed in polymer and aligned in the direction perpendicular to electromagnetic wave propagation. The permittivity of magnetic composite is increased as forging time increasing, while the permeability is decreased slightly. The maximum attenuation peak of reflection loss is shifted to lower fiequency range as milling time increasing, and the value of maximum attenuation peak is to get smaller gradually. From these result, we could designed a noise absorber sheet (t=1.0 mm) for quasi-microwave band, which is impedance matched at 1.4 GHz with respect to -8.2 dB reflection 1055.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.861-867
• /
• 2015

The Compact Tension (CT) type test was performed in order to evaluate the fracture toughness performance of glass fiber-reinforced laminated timber. Glass fiber textile and sheet Glass fiber reinforced plastic were used as reinforcement. The reinforced laminated timber was formed by inserting and laminating the reinforcement between laminated woods. Compact tension samples are produced under ASTM D5045. The sample length was determined by taking account of the end distance of 7D, and bolt holes (12 mm, 16 mm, 20 mm) had been made at the end of artificial notches in advance. The fracture toughness load of sheet fiberglass reinforced plastic reinforced laminated timber was increased 33 % in comparison to unreinforced laminated timber while the glass fiber textile reinforced laminated timber was increased 152 %. According to Double Cantilever Beam theory, the stress intensity factor was 1.08~1.38 for sheet glass fiber reinforced plastic reinforced laminated timber and 1.38~1.86 for glass fiber textile reinforced laminated timber, respectively. That was because, for the glass fiber textile reinforced laminated timber, the fiber array direction of glass fiber and laminated wood orthogonal to each other suppressed the split propagation in the wood.