• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1101-1107
• /
• 2004

This paper presents an optimization algorithm and technique for designing parallel Cyclic Redundancy Check (CRC) circuit, which is most widely adopted for error detection A new heuristic algorithm is developed to find as many shared terms as possible, thus eventually to minimize the number and level of the exclusive-or logic blocks in parallel CRC circuits. 16-bit and 32-bit CRC generators are designed with different types of Programmable Logic Devices, and it has been found that our new algorithm and architecture significantly reduce the delay.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.697-705
• /
• 2014

A single chip Programmable AC to DC Power Converter, consisting of wide band gap SiC MOSFET and SiC diodes, has been proposed which converts high frequency ac voltage to a conditioned dc output voltage at user defined given power level. The converter has high conversion efficiency because of negligible reverse recovery current in SiC diode and SiC MOSFET. High frequency operation reduces the need of bigger size inductor. Lead inductors are enough to maintain current continuity. A complete electrical analysis, die area estimation and thermal analysis of the converter has been presented. It has been found that settling time and peak overshoot voltage across the device has reduced significantly when SiC devices are used with respect to Si devices. Reduction in peak overshoot also increases the converter efficiency. The total package substrate dimension of the converter circuit is only $5mm{\times}5mm$. Thermal analysis performed in the paper shows that these devices would be very useful for use as miniaturized power converters for load currents of up to 5-7 amp, keeping the package thermal conductivity limitation in mind. The converter is ideal for voltage requirements for sub-5 V level power supplies for high temperatures and space electronics systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.349-351
• /
• 2013

This research paper presents a low-power programmable gain amplifier (PGA) to facilitate signal processing of the detection of defects in steel plates. This circuit is able to adjust a gain in the range of 6 to 60dB in 7 steps using different signal types for various defects from hall sensors. The gain of PGA is designed by operating on-resistors of switches and passive components. The proposed PGA ($0.18{\mu}m$ CMOS process with 1.8 supply voltage) showed excellent gain error of less than -0.2dB, and low power consumption of 0.47mW.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.388-389
• /
• 2022

Recently, AI (Artificial Intelligence) has been applied to various technologies such as automatic driving, robot and smart communication. Currently, AI system is developed by software-based method using tensor flow, and GPU (Graphic Processing Unit) is employed for processing unit. However, if software-based method employing GPU is used for AI applications, there is a problem that we can not change the internal circuit of processing unit. In this method, if high-level jobs are required for AI system, we need high-performance GPU, therefore, we have to change GPU or graphic card to perform the jobs. In this work, we developed a CNN-based FPGA (Field Programmable Gate Array) chip to solve this problem.

• Journal of Practical Engineering Education
• /
• v.8 no.2
• /
• pp.111-120
• /
• 2016

Education equipment for field programmable gate array (FPGA) design of sensor-based IOT (Internet Of Thing) system is introduced. Because sensors have different interfaces, several types of interface controller on FPGA need. Using this equipment, several types of interface controller, which can control ADC (analog-to-digital converter) for analog sensor outputs and $I^2C$ (Inter-Integrated Circuit), SPI (Serial Peripheral Interface Bus), and GPIO (General-Purpose Input/Output) for digital sensor outputs, can be designed on FPGA. Image processing hardware using image sensors and display controller for real and image-processed images or videos can be design on FPGA chip. This equipment can design a SOC (System On Chip) consisting of a hard process core on Linux OS and a FPGA block for IOT system which can communicate with wire and wireless networks. Using the education equipment, an example of hardware design using image sensor and accelerometer is described, and an example of syllabus for "Digital system design using FPGA" course is introduced. Using the education equipment, students can develop the ability to design some hardware, and to train the ability for the creative capstone design through conceptual, partial-level, and detail designs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1734-1740
• /
• 2012

In this paper, we propose a FSOURCE circuit which requires such a small switching current that an eFuse OTP memory can be programmed in the post-package state of the PMIC chips using a single power supply. The proposed FSOURCE circuit removes its short-circuit current by using a non-overlapped clock and reduces its maximum current by reducing the turned-on slope of its driving transistor. Also, we propose a DOUT buffer circuit initializing the output data of the eFuse OTP memory with arbitrary data during the power-on reset mode. We design a 24-bit differential paired eFuse OTP memory which uses Magnachip's $0.35{\mu}m$ BCD process, and the layout size is $381.575{\mu}m{\times}354.375{\mu}m$($=0.135mm^2$).

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.161-169
• /
• 2020

In order to reduce the manufacturing cost of MCU chips used in applications such as wireless chargers and USB-C, compared to DP-EEPROM (Double Poly EEPROM), which requires 3 to 5 additional process masks, it is even more necessary MTP(Multi-Time Programmable), which is less than one additional mask and have smaller unit cell size. In addition, in order to improve endurance characteristics and data retention characteristics of the MTP memory cell due to E/P(Erase / Program) cycling, the distribution of the V_TP(Program Threshold Voltage) and the V_TE(Erase Threshold Voltage) needs to be narrow. In this paper, we proposed a current-type BL S/A(Bit-Line Sense Amplifier) circuit, WM(Write Mask) circuit, BLD(BL Driver) circuit and a algorithm, which can reduce the distribution of program and V_T and erase V_T, through compare the target current by performing the erase and program pulse of the short pulse several times, and if the current specification is satisfied, the program or erase operation is no longer performed. It was confirmed that the 256Kb MTP memory fabricated in the Magnachip semiconductor 0.13㎛ process operates well on the wafer in accordance with the operation mode.

• ETRI Journal
• /
• v.31 no.5
• /
• pp.576-584
• /
• 2009

A novel tunable transconductor is presented. Input transistors operate in the triode region to achieve programmable voltage-to-current conversion. These transistors are kept in the triode region by a novel negative feedback loop which features simplicity, low voltage requirements, and high output resistance. A linearity analysis is carried out which demonstrates how the proposed transconductance tuning scheme leads to high linearity in a wide transconductance range. Measurement results for a 0.5 ${\mu}m$ CMOS implementation of the transconductor show a transconductance tuning range of more than a decade (15 ${\mu}A/V$ to 165 ${\mu}A/V$) and a total harmonic distortion of -67 dB at 1 MHz for an input of 1 Vpp and a supply voltage of 1.8 V.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.486-490
• /
• 2004

Programmable logic controller (PLC) is widely used in manufacturing system or process control. This paper presents the design of a 32-bit microprocessor for a sequence control using an Application Specification Integrated Circuit (ASIC). The 32-bit microprocessor was designed by a VHDL with top down method; the program memory was separated from the data memory for high speed execution of 274 specified sequence instructions. Therefore it was possible that sequence instructions could be operated at the same time during the instruction fetch cycle. And in order to reduce the instruction decoding time and the interface time of the data memory interface, an instruction code size was implemented by 32-bits. And the real time debugging as single step run, break point run was implemented. Pulse instruction, step controller, master controllers, BIN and BCD type arithmetic instructions, barrel shit instructions were implemented for many used in PLC system. The designed microprocessor was synthesized by the S1L50000 series which contains 70,000 gates with 0.65um technology of SEIKO EPSON. Finally, the benchmark was performed to show that designed 32-bit microprocessor has better performance than Q4A PLC of Mitsubishi Corporation.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.563-568
• /
• 2005

A motion-control chip contains major functions that are necessary to control the position of each motor, such as generating velocity command profiles, reading motor positions, producing control signals, driving several types of servo amplifiers, and interfacing host processors. Existing motion-control chips can only generate velocity profiles of fixed characteristics, typically linear and s-shape smooth symmetric curves. But velocity profiles of these two characteristics are not optimal for all tasks in industrial robots and automation systems. Velocity profiles of other characteristics are preferred for some tasks. This paper proposes a motion-control chip to generate velocity profiles of desired acceleration and deceleration characteristics. The proposed motion-control chip is implemented with a field-programmable gate array by using the Very High-Speed Integrated Circuit Hardware Description Language and Handel-C. Experiments using velocity profiles of four different characteristics will be performed.