• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.431-441
• /
• 2003

This paper presents the design of 32 bit microprocessor for a sequence control using a field programmable gate array(FPGA). The microprocessor was designed by a VHDL with top down method, the program memory was separated from the data memory for high speed execution of sequence instructions. Therefore it was possible that sequence instructions could be operated at the same time during the instruction fetch cycle. In order to reduce the instruction decoding time and the interface time of the data memory interface, an instruction code size was implemented by 32 bits. And the real time debug operation was implemented for easeful debugging the designed processor with a single step run, PC break point run, data memory break point run. Also in this designed microprocessor, pulse instructions, step controllers, master controllers, BM and BCD type arithmetic instructions, barrel shift instructions were implemented for sequence logic control. The FPGA was synthesized under a Xilinx's Foundation 4.2i Project Manager using a V600EHQ240 which contains 600,000 gates. Finally simulation and experiment were successfully performed respectively. For showing good performance, the designed microprocessor for the sequence logic control was compared with the H8S/2148 microprocessor which contained many bit instructions for sequence logic control. The designed processor for the sequence logic showed good performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.21-27
• /
• 2008

This paper describes a CMOS 16:1 binary-tree multiplexer(MUX) using $0.18-{\mu}m$ technology. To provide immunity for wide frequency range and process-and-temperature variations, the MUX adopts several delay compensation techniques. Simulation results show that the proposed MUX maintains the setup margins and hold margins close to the optimal value, i.e., 0.5UI, in wide frequency-range and in wide process-and-temperature variations, with standard deviation of 0.05UI approximately. These results represent that these proposed delay compensations are effective and the reliability is much improved although CMOS logic circuits are sensitive to those variations. The MUX is fabricated using $0.18-{\mu}m$ CMOS process, and tested with a test board. At power supply voltage of 1.8-V, maximum data-rate and area of the MUX is 1.65-Gb/s and 0.858 $mm^2$, respectively. The MUX dissipates a power of 24.12 mW, and output eye opening is 272.53 mV, 266.55 ps at 1.65-Gb/s operation.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.2
• /
• pp.34-38
• /
• 2013

AC Losses for face to face stacks of four identical coated conductors (CCs) were numerically calculated using the H-formulation combined with the E-J power law and the Kim model. The motive sample was the face to face stack of four 2 mm-wide CC tapes with 2 ${\mu}m$ thick superconducting layer of which the critical current density, $J_c$, was $2.16{\times}10^6A/cm^2$ on IBAD-MgO template, which was suggested for the mitigation of ac loss as a round shaped wire by Korea Electrotechnology Research Institute. For the calculation the cross section of the stack was simply modeled as vertically aligned 4 rectangles of superconducting (SC) layers with $E=E_o(J(x,y,t)/J_c(B))^n$ in x-y plane where $E_o$ was $10^{-6}$ V/cm, $J_c$(B) was the field dependence of current density and n was 21. The field dependence of the critical current of the sample measured in four-probe method was employed for $J_c$(B) in the equation. The model was implemented in the finite element method program by commercial software. The ac loss properties for the stacks were compared with those of single 4 cm-wide SC layers with the same critical current density or the same critical current. The constraint for the simulation was imposed in two different ways that the total current of the stack obtained by integrating J(x,y,t) over the cross sections was the same as that of the applied transport current: one is that one fourth of the external current was enforced to flow through each SC. In this case, the ac loss values for the stacks were lower than those of single wide SC layer. This mitigation of the loss is attributed to the reduction of the normal component of the magnetic field near the SC layers due to the strong expulsion of the magnetic field by the enforced transport current. On the contrary, for the other case of no such enforcement, the ac loss values were greater than those of single 4cm-wide SC layer and. In this case, the phase difference of the current flowing through the inner and the outer SC layers of the stack was observed as the transport current was increased, which was a cause of the abrupt increase of ac loss for higher transport current.

• Culinary science and hospitality research
• /
• v.16 no.3
• /
• pp.147-160
• /
• 2010

This study aims to analyze the effect of emotional response from dining out experience on satisfaction after dining out based on the customers who have visited a luxurious Korean restaurant. For this study, it designed a research model through literary research and derived hypotheses. For the empirical analysis, 250 copies of the questionnaire using the self-administered method were distributed and 230(94%) copies were collected. Among them, 220(88%) copies were used for the analysis. SPSS WIN Version 12.0 statistical package program was used for the analysis of data processing, the frequency analysis, reliability analysis and factor analysis were operated, and the hypothesis testing was verified by the regression analysis. The results of the analyses are as follows. For the hypothesis that "the dining-out consumption pattern will have a significant effect on the emotional response," it was verified that the style which pursues health and the style which is loyal to relationships had significant effects on pleasure while the style which pursues rest didn't. Also, the style which pursues health and the style which is loyal to relationships had significant effects on arousal while the style which pursues rest didn't. For the hypothesis that "emotional response will have a significant effect on satisfaction," it was verified that pleasure and simulation had significant effects on satisfaction. As a result of the study, the current dining-out consumption pattern is changed from the purpose of having meals for the biological needs in the past to considering emotional response such as preferred taste or mood.

• Progress in Medical Physics
• /
• v.17 no.4
• /
• pp.192-200
• /
• 2006

We evaluated the positional accuracy of the delivered beams to the target in a phantom by simulating the whole process of the radiation treatments Including CT scanning, planning and beam exposures with MLCs. For this purpose, a phantom was made to calibrate the alignment between the CT and the attached laser system. A new, convenient method was also devised to align the setup lasers in the treatment room. Film was used for the Identification of the delivered beam and analyzed with a homemade computer program. The positional differences between the target and the beam centers varied with the couch rotations. The accelerator we used showed a maximum discrepancy of 2.0 mm at the table angle of $295^{\circ}$. The same measurements based on the new isocenter from the Winston-Lutz test resulted in the maximum of 1.35 mm for all rotation angles. The evaluation of the differences between the target and the beam centers is useful for the treatment planning.

• Journal of Navigation and Port Research
• /
• v.29 no.1 s.97
• /
• pp.91-96
• /
• 2005

The National Marine Electronics Association(NMEA) is nonprofit-making cooperation composed with manufacturers, distributors, wholesalers and educational institutions. We use the basic port of equipment in order to process the signal from NMEA signal using equipment. When we don't have enough one, we use the multi-port for processing. However, we need to have module development simulation which could multiplex and provide NMEA related signal that we could solve the problems in multi-port application and exclusive equipment generation for a number of signal. For now, we don't have any case or product using NMEA multiplexer so that we import expensive foreign equipment or embody NMEA signal transmission program like software, using multi-port. These have problems since we have to pay lots ci money and build separate processing part for every application programs. Besides, every equipment generating NMEA signal are from different manufactures and have different platform so that it could cause double waste and loss of recourse. For making up for it, I suggest the NMEA multiplexer embodiment, which could independently move by reliable process and high performance single hardware module, improve the memory efficiency of module by designing the optimized Queue, and keep having reliability for realtime communication among the equipment such as main input sensor equipment Gyrocompass, Echo-sound, and GPS.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.48-48
• /
• 2011

본 연구에서는 미래 기후변화가 하천 및 호소수질에 미치는 영향을 평가하고자 유역 수문-수질 모의가 가능한 SWAT(Soil and water assessment tool) 모형과 호소수질 모의가 가능한 WASP(Water Quality Simulation Program) 모형을 연계운영하여 충주호를 포함하는 충주댐 유역($6,642.0km^2$)에 적용하였다. 이를 위해 IPCC(Intergovernmental panel on climate change)에서 제공하는 A1B 배출시나리오를 포함하는 MIROC3.2 hires 모형의 결과로부터 충주댐 유역의 총 6개 기상관측소에 대한 과거 30년(1997~2006) 실측자료를 바탕으로 미래 온도와 강수에 대한 편이보정(Bias correction) 및 Change Factor Method로 상세화(Downscaling)하여 미래 기후자료(2020s, 2050s, 2080s)를 생산하였다. 미래 연평균 온도는 기준년도인 2000년에 비해 최대 $+4.8^{\circ}C$(2080s)의 온도증가를 보였으며, 강수량의 경우 여름과 가을 강수량이 다소 감소하였으나 연평균 강수량은 최대 +34.4%(2080s) 증가하는 것으로 전망되었다. 먼저, SWAT 모형을 이용한 기후변화에 따른 댐 유입량은 39.8%(2080s) 증가는 것으로 분석되었으며 유역의 유출특성 변화로 인한 유사량은 지표유출변화에 기인하여 봄과 겨울에 증가하는 경향과 함께 -14.5%(2020s) ~ +27.3%(2080s)의 변화를 보이는 것으로 분석되었다. 영양물질에 대한 오염부하량은 2080s에서 T-N이 증가추세를 보이며 최대 87.3% 까지 증가하는 반면, T-P는 유사량과 유사한 변화패턴을 보이며 최대 48.4%까지 감소하는 것으로 분석되었다. 호소수질 모델링을 위한 충주호의 Segment 구성은 충주댐1 지점에서부터 충주댐4 지점까지 전체 수표면적 $65.7km^2$에 대하여 상층과 하층 총 760개로 구성하였으며, SWAT 모형에 의한 충주호 유입하천 소유역에서의 미래 유출 및 영양물질 자료를 WASP 모형의 초기값으로 입력하여 수체 내의 BOD, Chl-a, T-N, T-P 변화 분석을 실시하였다. 이와 같이 지구 온난화에 의한 기후변화는 강우특성 변화에 따른 가뭄과 홍수 등 극한 기상현상의 발생, 유역 물순환 체계 변화를 야기 시키므로서 수자원 부존량 변화에 영향을 미칠 뿐만 아니라 기온상승에 따른 수온변화, 비점오염물질의 거동에도 변화를 초래하여 하천 및 호소 수질에 큰 영향을 미칠 것으로 판단된다.

• The KIPS Transactions:PartC
• /
• v.12C no.6 s.102
• /
• pp.773-780
• /
• 2005

Recently, the telecommunication network is in a transition toward the BcN (Broadband convergence Networks) that integrates the Internet, the telecommunication and the broadcasting. The BcN makes it possible to provide of 4he third-party application by using the Open API The Parlay X API is an example of the Open API and the Parlay X API is grafted in the Web Service and is abstracted from the Parlay API. So, the Parlay X API does not only have advantages of a Web Service, but also disadvantages of the Web Service. The main disadvantage of the Web Service is that it does not support the any QoS mechanism. In this paper, we propose the architecture that solves the reliability among the QoS issues for the Web Service. The proposed mechanism adopts the Asynchronous architecture for the reliable Web Service and improves the performance of the retransmission between the client and the server using the expected response time. We perform the performance evaluation through the simulation in older to compare with the existing mechanism. Consequently, we can confirm that the performance of the proposed mechanism performs better than the existing mechanism.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.644-649
• /
• 2017

In the automobile industry, there is growing demand for lightweight vehicles due to environmental problems and rising oil prices. Therefore, aluminum alloys and special materials are being used to reduce the weight of vehicles, but there are still many difficulties to overcome in terms of cost and strength. Therefore, the application of advanced high strength steel (AHSS)is increasing. AHSS has good strength and formability.Safety regulations are becoming stricter, and 1.2-GPa super-high-strength steels are gradually being applied for the center pillar and roof rails. Thus, the application of different kinds of steels in automobile bodiesis also increasing gradually. This study evaluates the resistance point weldability and the characteristics of a welded part of SGAFC1180 1.2t steel. A simulation was used to observe the nugget formation and its growth behavior. The prediction performance showed a similar tendency within an error rate of 10%. Also, the effect of this behavior on the process resistance and dynamic resistance was investigated,along with the correlation between the shear tensile strength and nugget diameter.

• Tunnel and Underground Space
• /
• v.25 no.2
• /
• pp.186-198
• /
• 2015

This paper aims for the ultimate goal to optimize the work place environment through assuring the optimal required ventilation rate based on the analysis of the airflow. The working environment is deteriorated due to a rise in temperature of a coal mine caused by increase of its depth and carriage tunnels. To improve the environment, the ventilation evaluation on J coal mine is carried out and the effect of a length of the tunnel on the temperature to enhance the ventilation efficiency in the subsurface is numerically analyzed. The analysis shows that J coal mine needs $17,831m^3/min$ for in-flow ventilation rate but the total input air flowrate is $16,474m^3/min$, $1,357m^3/min$ of in-flow ventilation rate shortage. The temperatures were predicted on the two developed models of J mine, and VnetPC that is a numerical program for the flowrate prediction. The result of the simulation notices the temperature in the case of developing all 4 areas of -425ML as a first model is predicted 29.30 at the main gangway 9X of C section and in the case of developing 3 areas of -425ML excepting A area as a second model, it is predicted 27.45 Celsius degrees.