• Design & Manufacturing
• /
• 제17권4호
• /
• pp.63-71
• /
• 2023

In order to increase the extrusion production speed of aluminum, extrusion die cooling technology using liquid nitrogen has recently attracted a lot of attention. Increasing the extrusion speed increases the temperature of the bearing area of extrusion dies and the extrusion profile, which may cause defects on the surface of extruded profile. Extrusion die cooling technology is to directly inject liquid nitrogen through a cooling channel formed between the die and the backer inside the die-set. The liquid nitrogen removes heat from the die-set, and gaseous nitrogen at the exit of the channel, covers the extrusion profile of an inert atmosphere reducing the oxidation and the profile temperature. The aim of this study is to evaluate the cooling capacity by applying die cooling to extrusion of Al-Mn-based aluminum alloy flat tubes, and to investigate the effects of die cooling on the change in extrusion characteristics of flat tubes. Cooling capacity was confirmed by observing the temperature change of the extrusion profile depending on whether or not die cooling is applied. To observe changes in material characteristics due to die cooling, surface observation is conducted and microstructure and precipitate analysis are performed by FE-SEM on the surface and longitudinal cross section of the extruded flat tubes.

• Fibers and Polymers
• /
• 제1권2호
• /
• pp.103-110
• /
• 2000

Flow analysis of profile extrusion is essential for design and production of a profile extrusion die. Velocity, pressure, and temperature distribution in an extrusion die are predicted and compared with the experimental results. A two dimensional numerical method is proposed for three dimensional analysis of the flow field within the profile extrusion die by applying a modified cross-sectional numerical method. Since the cross-sectional shape of the die is varied gradually, it is assumed that the pressure is constant within a cross-sectional plane that is perpendicular to the flow direction. With this assumption, the velocity component in the cross-sectional direction is neglected. The exact cross-sectional shape at any position is calculated based on the geometry of standard cross-sections. The momentum and energy equations are solved with proper boundary conditions at a cross-section and then the same calculation is carried out for the next cross-section using the current calculated values. An L-shaped profile extrusion die is produced and employed for experimental investigation using a commercially available polypropylene. Numerical prediction for the varying cross-sectional shape provides better results than the previous studies and is in good agreement with the experimental results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.110-113
• /
• 2008

This study was performed to predict the shape of polymer extrusion product and to find the cause of defective products Experiments was performed to extrude the complex profile shape using PC/ABS composite resin with new profile die and cooling die. A finite element analysis for the Polymer Extrusion process considering the heat transfer and thermal deformation was also performed, and the result was compared with the experimental data. It is found that the predicted profile shape in F. E. M was similar to the experimental result and the thickness of extruded product was thin when the velocity of profile die outlet was slow than the velocity of production (2m/min).

• Korea-Australia Rheology Journal
• /
• 제13권2호
• /
• pp.97-106
• /
• 2001

Three-dimensional flow analysis was performed by using the control volume finite-element method for design of a profile extrusion die. Because polymer melt behavior is complicated and cross-sectional shape of the profile extrusion die is changing continuously, the fluid flow within the die must be analyzed three-dimensionally. A commercially available polypropylene is used for theoretical and experimental investigations. Material properties are assumed to be constant except for the viscosity. The 5-constant modified Cross model is used for the numerical analysis. A test problem is examined in order to verify the accuracy of the numerical method. Simulations are performed for conditions of three different screw speeds and three different die temperatures. Predicted pressure distribution is compared with the experimental measurements and the results of the previous two-dimensional study. The computational results obtained by using three dimensional CVFEM agree with the experimental measurements and are more accurate than those obtained by using the two-dimensional cross-sectional method. The velocity profiles and the temperature distributions within several cross-sections of the die are given as contour plots.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.34-41
• /
• 2021

Interventional radiology and minimally invasive surgery both require a precisely shaped microcatheter. Microcatheters are manufactured using polymer extrusion processes with a die and puller. The manufacturing parameters and die geometry greatly influence the profile of the extrudate and designing dies using a trial-and-error process is expensive and requires a lot of time. Therefore, predicting the profile of the extrudate is important for manufacturing microcatheters. This study investigates the effects of die design and geometry on the profile of the extrudate. The profiles of the extrudate are predicted using ANSYS Polyflow with respect to the different die geometries. The outer and inner diameters and wall thickness of the predicted extrudate are compared to those of a target extrudate. The die swell of melt polymer and the effect of the pulling are both examined. Optimized die designs are suggested for manufacturing the target extrudate.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 추계학술대회논문집
• /
• pp.185-191
• /
• 1996

The Variation of die bearing is primary way to control the metal flow in hot square die extrusion process. Finite element computations are carried out to assess the influence of die bearing on metal flow and state variables. The finit element method is developed based on ALE description for a rigid-viscoplastic material. Since thermal state computational example, hot square die extrusion with varied die bearing lengths has been analyzed for the profile of a L-section.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.98-101
• /
• 2001

In the present study, several design parameters of the flat-die extrusion process are investigated using the rigid-plastic finite element method. The effect of loaction of extrusion profile, arrangement of multiple extrusion profiles, and design of various die land has been investigated through the analysis. Several numerical examples of flat-die extrusion, such as C-section, multiple U- shape, and window guide extrusion, are analyzed. From the comparative study, the effect of design parameters is investigated. In each example, comparing the velocity distribution with that of the original design, it has been shown that the design modification affords much more uniform distribution of axial velocity

• 소성∙가공
• /
• 제8권5호
• /
• pp.471-481
• /
• 1999

The properties of deformed products are generally dependent upon the distribution of microstureture. It is, therefore, necessary to make the distribution of microstureture uniform in order to achieve the best balance of properties in the final product. This is often a demanding task, even for conventional materials. It is become essential to achieving mechanical integrity and a desired combination of microstructure and properties. The objective mechanical integrity and a desired combination of microsttucture and properties. The objective of this study is to design the optimal die profile which can yield more uniform microstructure in hot extruded product. The microstructure evolution, such as dynamic and static recrystallization as well as grain growth, is investigated using the program com-bined with yada and Senuma's empirical equations and rigid-thermoviscoplastic finite element method. The die profile of hot extrusion is represented by Bezier-curve to define all available profile. In order to obtain the optimal die profile which yields uniform microstructure in the product the FPS(Flexible Polyhedron Search) method is applied to the present study. To validate the result of present study the experimental hot extrusion is performed and the result is compared with that of simulation.

• 소성∙가공
• /
• 제10권7호
• /
• pp.551-557
• /
• 2001

In the present study, several design parameters of the flat-die extrusion process are investigated using the finite element method. The effects of the location of an extrusion profile, arrangement of multiple extrusion profiles, and the design of various die land have been investigated through the analysis. Several numerical examples of flat-die extrusion of such as C-section, multiple U-shape, and a window guide section, are analyzed. From the comparative study, the effect of design parameters is investigated. In each example, comparing the velocity distribution with that of the original design, it has been shown that the design modification affords more uniform distribution.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.265-268
• /
• 2003

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, new designs of lip die are proposed.