• 한국정밀공학회지
• /
• 제17권6호
• /
• pp.111-118
• /
• 2000

The design of reference trajectory with respect to drag acceleration is necessary to decelerate from hypersonic speed safely after atmosphere re-entry of space vehicle. The re-entry guidance design involves trajectory optimization, generation of a reference drag acceleration profile with the satisfaction of 6 trajectory constraints during the re-entry flight. This reference drag acceleration profile can be considered as the reference trajectory. The cost function is composed of the accumulated total heating on vehicle due to the reduction of weight. And a regularization is needed to prevent optimal drag profile from varying too fast and achieve realized trajectory. This paper shows the relations between velocity, drag acceleration and altitude in drag acceleration profile, and how to determine the reference trajectory.

• Journal of Ship and Ocean Technology
• /
• 제1권2호
• /
• pp.11-18
• /
• 1997

The leading edge of a low-drag super-cavitating foil has been made to be thick enough by using a point drag which is supposed to be a linear model of the Kirchhoff lamina. In the present paper, the relation between the point drag and the Kirchhoff lamina is made clear by analyzing the cavity drag of both models and the leading edge radius of the point drag model and the lamina thickness of Kirchhoff\`s profile K. The matched asymptotic expansion is effectively made use of in designing a practical super-cavitating fool which is not only of low drag but also structurally sound. Also it has a distinct leading edge cavity separation point. The cavity foil shapes of trans-cavitating propeller blade sections designed by present method are shown.

• Wind and Structures
• /
• 제16권2호
• /
• pp.193-211
• /
• 2013

This paper presents results from a wind tunnel study that examined the drag coefficient and wind flow over an asymmetric wave train immersed in turbulent boundary layer flow. The modeled wavy surface consisted of eight replicas of a statistically-valid hurricane-generated wave, located near the coast in the shoaling wave region. For an aerodynamically rough model surface, the air flow remained attached and a pronounced speed-up region was evident over the wave crest. A wavelength-averaged drag coefficient was determined using the wind profile method, common to both field and laboratory settings. It was found that the drag coefficient was approximately 50% higher than values obtained in deep water hurricane conditions. This study suggests that nearshore wave drag is markedly higher than over deep water waves of similar size, and provides the groundwork for assessing the impact of nearshore wave conditions on storm surge modeling and coastal wind engineering.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.361-364
• /
• 1997

The re-enty guidance design involves trajectory optimization, generation of a reference drag acceleration profile with the satisfaction of trajectory constraints. This reference drag acceleration profile can be considered as the reference trajectory. This paper proposes the atmospheric re-entry system which is composed of longitudinal, later and range control. This paper shows the a performance of a re-entry guidance and control system using feedback linearization control and predictive control.

• 동력기계공학회지
• /
• 제7권4호
• /
• pp.67-73
• /
• 2003

The entry guidance design involves trajectory optimization and generation of a drag acceleration profile as the satisfaction of trajectory conditions during the entry flight. The reference trajectory is parameterized and optimized as piecewise linear functions of the velocity. A regularization technique is employed to achieve desired properties of the optimal drag profile. The regularized problem has smoothness properties and the minimization of performance index then prevents the drag acceleration from varying too fast, thus eliminating discontinuities. This paper shows the trajectory control using the simple control law as well as the information of reference drag acceleration.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.199-202
• /
• 2006

The objective of this study is to propose methods of controlling the wake behind a sphere for drag reduction using the suboptimal control theory and surrogate management framework, respectively. The Reynolds numbers considered is 300 at which the base flow is unsteady planar symmetric. Given the cost function defined as the square of the difference between the target pressure (potential-flow pressure) and real flow pressure on the sphere surface, the suboptimal control makes the flow steady axisymmetric and produces drag reduction. Based on the actuation profile from the suboptimal control, the optimal wavy actuation profile is obtained using the surrogate management framework and produces drag reduction.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.1-8
• /
• 2000

A modified low-Reynolds-number Reynolds stress model is developed for the calculation of drag-reducing turbulent flows induced by polymer injection. The results without polymer injection are compared with the results of direct numerical simulation to ensure the validity of the basic model. In case of drag reduction, profiles of mean velocity and Reynolds stress components, in two-dimensional channel flow, obtained with a proper value of viscosity ratio are presented and discussed. Computed mean velocity profile is in very good agreement with experimental data. And, the qualitative behavior of Reynolds stress components with the viscosity ratio is also reasonable.

• International Journal of Aeronautical and Space Sciences
• /
• 제16권2호
• /
• pp.311-324
• /
• 2015

This study presents computational analyses for low-drag aerodynamic design that are applied to modify a long-endurance UAV. EAV-2 is a test-bed for a hybrid electric power system (fuel cell and solar cell) that was developed by the Korean Aerospace Research Institute (KARI) for use in future long-endurance UAVs. The computational investigation focuses on designing a wing with a reduced drag since this is the main contributor of the aerodynamic drag. The airfoil and wing aspect ratio of the least drag are defined, the fuselage configuration is modified, and raked wingtips are implemented to further reduce the profile and induced drag of EAV-2. The results indicate that the total drag was reduced by 54% relative to EAV-1, which was a small-sized version that was previously developed. In addition, static stabilities can be achieved in the longitudinal and lateral-directional by this low-drag configuration. A long-endurance flight test of 22 hours proves that the low-drag design for EAV-2 is effective and that the average power consumption is lower than the objective cruise powerof 200 Watts.

• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.333-339
• /
• 2012

The main objective of the present study is to investigate the roles of the micro-dimpled surface on the drag reduction. To investigate the effectiveness of the micro-dimpled surface, the flat plates are prepared. The micro-size dimples are directly carved on the metal surface by ultrasonic nano-crystal surface modification (UNSM) method. Momentum of the main flow is increased by the dimple patterns within the turbulent boundary layer (TBL), however, there is no significant change in the turbulence intensity in the TBL. The influence of dimple patterns is examined through the flow field survey near the flat plate trailing edge in terms of the profile drag. The wake flow velocities in the flat plate are measured by PIV technique. The maximum drag reduction rate is 4.6% at the Reynolds number of $10^6{\sim}10^7$. The dimples tend to increase the drag reduction rate consistently even at high Reynolds number range.

• 한국항공우주학회지
• /
• 제49권8호
• /
• pp.637-648
• /
• 2021

본 논문에서는 한국형 우주비행기(KSP)에 대한 새로운 재진입 유도를 제안하고자 한다. 제안된 방법은 우주 왕복선 유도 개념과 유사하게 다양한 비행경로 제약조건과 경계조건을 만족시키는 기준 항력 프로파일을 미리 결정하고, 결정된 기준 항력 프로파일을 추종하는 방식으로 유도명령이 구현된다. 이를 위해 본 연구에서는 항력 동역학을 조사하였으며, 그 결과 항력과 비행경로각의 동역학적 응답 특성이 상당히 다르다는 사실이 밝혀졌다. 이 사실을 바탕으로 제안한 유도명령은 시간분리 기법과 궤환선형화 방법을 사용하여 결정된다. 제안한 유도기법의 주요 특징은 간단한 구조와 명확한 작동 메커니즘에 있다. 따라서 제안된 방법은 기존 방법에 비해 구현이 간단하다. 본 논문에서는 제안된 방법의 성능을 조사하기 위해 수치 시뮬레이션을 수행한다.