• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.102-105
• /
• 2001

In this paper, the solution of two dimensional deflection of circular wavy elastica beam was obtained for one end clamped boundary and concentrated load condition. The beam was regarded as a linear elastic material. Wavy shape was described as a combination of half-circular arc smoothly connected each other with constant curvature of all the same magnitude and alternative sign. Also load direction was taken into account. As a result, the solution was expressed in terms of a series of integral equations. While we found the exact solutions and expressed them in terms of elliptic integrals, the recursive ignition formulae about the displacement and arc length at each segment of circular section were obtained. Algorithm of determining unknown parameters was established and the profile curve of deflected beam was shown compared with initial shape.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.163-169
• /
• 2001

The solution of two-dimensional deflection of circular wavy reinforcing fiber elastics was obtained for one end clamped boundary under concentrated load condition. The fiber was regarded as a linear elastic material. Wavy shape was described as a combination of half-circular arc smoothly connected each other with constant curvature of all the same magnitude and alternative sign. Also load direction was taken into account. As a result, the solution was expressed in terms of a series of elliptic integrals. These elliptic integrals had two different transformed parameters involved with load value and initial radius of curvature. While we found the exact solutions and expressed them in terms of elliptic integrals, the recursive ignition formulae about the displacement and arc length at each segment of circular section were obtained. Algorithm of determining unknown parameters was established and the profile curve of deflected beam was shown in comparison with initial shape.

• Journal of Mechanical Science and Technology
• /
• v.14 no.9
• /
• pp.978-984
• /
• 2000

The aim of this study is to investigate the ductile fracture behaviour under Mode I loading using SA533B pressure vessel steel. Experiments consist of the Round Notch Bar Test (RNB), Single Edge Crack Bending Test (SECB), and V-Notch Bar Test (VNB). Results from the RNB test were used to tune the damage modelling constant. The other tests were performed to acquire the J-resistance curves and to confirm the damage constants. Microstructural observation includes the measurement of crack profile to obtain the roughness parameter. Finally, simulation using Rousellier Ductile Damage Theory (RDDT) was carried out with 4-node quadrilateral element ($L_c=0.25\;mm$). For the crack advance, the failed element removal technique was adopted with a ${\beta}$ criterion. In conclusion, the predicted simulation using RDDT showed a good agreement with the experimental results. A trial using a roughness parameter was made for a new evaluation of J-resistance curve, which is more conservative than the conventional one.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.460-463
• /
• 2005

Gear is an important machine element to be used transmission in case short between axis. We drew gear using automatic design program to solve problem when it draw gear. We manufactured gears that it have different pressure angles using W-EDM. And we got a 2D profile of manufactured gear using reverse engineering. So we got to manufacturing error in comparison with CAD data and measured data. In result we could manufacture precise gear through improvement of manufacturing processes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.224-230
• /
• 1993

Closed-die forging of spur gears with hollow cylindrical billet has been analysed by using the upper-bound method. A kinematically admiccible velocity field has been developed. wherein, an involute curve has been introduced to represent the forging die profile. In the analysis, the deformation regions have been divided into nine zones. A constant frictional stress has been assumed on the contacting surfaces. Utilizing the formulated velocity field, numerical calcuations have been carried out to investigate the effects of various parameters, such as module, number of teeth and friction factor,on the forging of spur gears.

• Journal of Biosystems Engineering
• /
• v.23 no.5
• /
• pp.417-426
• /
• 1998

This study was intended to investigate the characteristics of loads acting on the transmission of agricultural tractors during plowing, rotavating and transporting operations. A survey was conducted to determine working speeds and transmission gears most frequently used for each operations. The transmission loads were measured at the input shaft of the transmission gear box during each operations. Time histories of the measured torque loads were converted into a load spectrum and analyzed with respect to the S-N curve of the shaft material to estimate the partial damages on the transmission. Finally, comparison of the relative damages and severeness of each operation was presented and discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1182-1191
• /
• 1994

This paper presents an enhanced method of slit beam projection intended for the rapid measurement of 3-dimensional surface profiles of dies and molds. Special emphasis is given to optimizing the design of optical system so that the measuring accuracy can be maximized by adopting two-plane camera calibration together with sub-pixel image processing techniques. Finally, several measurement examples are discussed to demonstrate that an actual measuring accuracy of $\pm$ 0.2 mm can be achieved over the measuring range of 500 mm{\times}300mm{\times}200mm$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.38-43
• /
• 2011

Industrial reducer is in general use to Deck Crane. High-precision and high-efficient reducer is minimized the power-loss and energy-loss of a machine. So it contribute the price reduction and life extension. Reducer is usually using the Planetary gear reducer. Planetary gear reducer is composed the sun gear, planet gear, internal gear and casing. Industrial reducer's wear and breakage have a short-life. To solve this problem, it is using the profile-shifted-gear or tooth modification. This study was carried out the effect of addendum modification coefficient on tooth fillet bending strength to planetary reducer. Tooth fillet bending stress is calculate. And all parameter were expressed the function of addendum modification coefficient. And then stress concentration factor of tooth fillet curve was express the function of addendum modification coefficient using comparison between theory and finite element analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.924-927
• /
• 2007

In this study, adaptation of two-way shape memory effect of SMA wire to the actuator is examined. Therefore the SMA characteristics which are training, material properties, response time at different thermal cycling rates are tested. During training, permanent deformation is accumulated till a certain number of cycle and then saturated. The amount of two-way strain is unchangeable over all cycle and the slope of strain(or stress)-temperature curve is slower as the increase of applied stress. The rate effect is observed resulted from the thermal distribution which heating profile differs from cooling as thermal cycling time. Using the estimated SMA properties, an experimental test for the simple smart wing is performed.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.21 no.1
• /
• pp.1-10
• /
• 2003

Printing ink is faced various shear stress situation until it transfer to the printed substrate through the press. And in each shear stress condition the ink is needed to keep the appropriate viscosity according to the condition. The change of printing ink viscosity has been explained by well-known through the viscosity profile curve. But actually, the quality of printed paper depends on the ink behavior after transfer the substrates. Like this, to look into the behaviour of the ink on the printed substrate, it is needed the experiment of the ink structure recovering by rheology study. In this study, by controling the $CaCO_3$ content in the ink, after investigating the effect of the ink's structure recovery of the pigment concentration, we intend to predict the printing quality of the ink behvior on the substrate depending on pigment content.