• ETRI Journal
• /
• v.27 no.5
• /
• pp.491-496
• /
• 2005

An application specific processor for an H.264 decoder with a configurable embedded processor is designed in this research. The motion compensation, inverse integer transform, inverse quantization, and entropy decoding algorithm of H.264 decoder software are optimized. We improved the performance of the processor with instruction-level hardware optimization, which is tailored to configurable embedded processor architecture. The optimized instructions for video processing can be used in other video compression standards such as MPEG 1, 2, and 4. A significant performance improvement is achieved with high flexibility. Experimental results show that we could achieve 300% performance for the H.264 baseline profile level 2 decoder.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2143-2146
• /
• 2003

We propose, for the first time to our knowledge, a novel gain-clamping method for EDFA in WDM Add/Drop networks by introducing a disturbance observer technique. The proposed gain-clamping control input consists of the nominal gain-clamping control such as PI(Proportional and Integral) control and the additional control input for the compensation of the effects caused by channel add/drops. The additional control input is designed using the wellknown disturbance observer technique and can be implemented very easily with general electric elements. We proved the superiority of the new technique over the previous methods by showing simulation result of minimized dips and spikes that appear in power profile of EDFA output.

• The Journal of Korea Robotics Society
• /
• v.11 no.1
• /
• pp.26-32
• /
• 2016

A variable release torque-based compliance spring-clutch (VCSC) is presented. VCSC is a safe joint to reduce the impact of collisions between humans and robots. It is composed of four functional plates, balls, springs to make some functions in compliant movement, release mechanism, gravity compensation during its work. Also, it can estimate torque applied to a joint by using distance sensor and parameters of cam profile. The measured variable torque of prototype is 4.3~7.6 Nm and release torque is 4.3 Nm. In our future studies, a calibration for torque estimation will be conducted.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.143-146
• /
• 1998

A new stereoscopic codec. structure using MPEG-2 multiview profile is presented in this paper. In the suggested codec., the left image is coded with motion estimation in the base layerand the right image is coded with disparity estimation in the enhancement layer. Since it is possible to calculate rough motion of the right image sequence with disparity and motion of the left image sequence, motion compensation of the enhancement layer is performed without motion estimation. Since the proposed codec. does not perform motion estimation in the enhancement layer encoding, it is simple and reduces the encoding time. We compared the PSNR of encoded image with three different structured codec., and the experimental results show that suggested codec. has comparable with other codecs.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.85.4-85
• /
• 2001

A learning controller is presented for repetitive walking motion of biped robot. The learning control scheme learns the approximate inverse dynamics input of biped walking robot and uses the learned input pattern to generate an input profile of different walking motion from that learnt. In the learning controller, the PID feedback controller takes part in stabilizing the transient response of robot dynamics while the feedforward learning controller plays a role in computing the desired actuator torques for feedforward nonlinear dynamics compensation in steady state. It is shown that all the error signals in the learning control system are bounded and the robot motion trajectory converges to the desired one asymptotically. The proposed learning control scheme is ...

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.4
• /
• pp.71-75
• /
• 2007

Geometrical error of ultra-precision machining due to spherical tool alignment error is analyzed. Deviation of spherical edge, ranged several ten micrometers, generates vertical and horizontal error of tool path and affects profile accuracy of machined surface. Simulation of machined error shows effect of tool alignment error and enables to estimate alignment error. This work provides technical insights into the minimizing of geometrical error of ultra-precision machining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.964-967
• /
• 2001

Aspherical lens with the higher numerical aperture has been needed in the optical storage device to increase the recording density on the disk. However, high numerical aperture means the large slope angle at the clear aperture of the lens. Therefore, the measurement and manufacturing technique including the lens molding process for the slope angle should be developed. In this paper, the evaluation technique was described for the optical performance of the aspherical lens. Aspherical form error brings about the wavefront error and the side lobe of the beam intensity profile. A schematic diagram of the aspherical lens manufacturing was drawn to explain the aspherical form error compensation. Finally, form error of the aspherical lens was defined and plotted using the raw data of the Formtalysurf.

• Journal of Mechanical Science and Technology
• /
• v.16 no.5
• /
• pp.633-638
• /
• 2002

An approach to enhance dimensional accuracy of the grinding process has been presented, and grinding of a glass material with a metal-bonded diamond wheel has been studied. In this study, a grinding tool is suspended flexibly and controlled by an electromagnetic actuator. During grinding, profile error of a ground surface is indirectly measured and fed back to a control system. A model of grinding error has been suggested on which the indirect measurement has been based. An optimal PID control is adopted and effectiveness of the in-process feedback control has been verified experimentally.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.5
• /
• pp.124-130
• /
• 2000

For measuring out the submicron order straightness, a precision measuring device is developed in this paper. The device is constructed with a hydrostatic feed table and a capacitive type sensor which is mounted to the feed table. Straightness is acquired as substracting the motion error of feed table from the measured profile with probe. Motion error of feed table is simultaneously compensated upto 0.120${\mu}{\textrm}{m}$ of linear motion error and 0.20arcsec of angular motion error using the active controlled capillary. Reversal method and strai호t-edge is used fur estimating the measuring accuracy and from the experimental result, it is verified that the device has the measuring accuracy 0.030m. Also, through the practical application on the measurement of ground surface, it is confirmed that the device is very effective to measure the submicron order straightness.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.27-28
• /
• 2008

For stable and sustainable energy supply, distributed generator (DG) has become an essential and indispensable element from environmental and energy security perspectives. However, installation of DG in distribution systems may cause negative affects on feeders because power outputs of DG could be changed irregularly. One of major negative affects is variation in voltage profile. In general, voltage regulation devices such as under load tap changer (ULTC) at distribution substation and step voltage regulator (SVR) along feeder in distribution system are used to maintain customers' receiving voltage within a predetermined range. These regulators are controlled by line drop compensation (LDC) method which calls for two parameters; the equivalent impedance and the load center voltage. Therefore, consideration of DG outputs in the LDC parameter design procedure may give large impact on the installable DG capacity. This paper proposes a method that estimates maximum Installable DG capacity considering LDC parameters of ULTC and SVR. The proposed algorithm is tested with model network.