• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.22 no.5
• /
• pp.27-43
• /
• 2019

This study applied the LANDIS-II model to the forest vegetation of the study area in Yeongdong-gun, Korea to identify climate effects on ecosystems of forest vegetation. The main purpose of the study is to examine the long-term changes in forest aboveground biomass(AGB) under three different climate change scenarios; The baseline climate scenario is to maintain the current climate condition; the RCP 4.5 scenario is a stabilization scenario to employ of technologies and strategies for reducing greenhouse gas emissions; the RCP 8.5 scenario is increasing greenhouse gas emissions over time representative with 936ppm of $CO_2$ concentration by 2100. The vegetation survey and tree-ring analysis were conducted to work out the initial vegetation maps and data for operation of the LANDIS model. Six types of forest vegetation communities were found including Quercus mongolica - Pinus densiflora community, Quercus mongolica community, Pinus densiflora community, Quercus variabilis-Quercus acutissima community, Larix leptolepis afforestation and Pinus koraiensis afforestation. As for changes in total AGB under three climate change scenarios, it was found that RCP 4.5 scenario featured the highest rate of increase in AGB whereas RCP 8.5 scenario yielded the lowest rate of increase. These results suggest that moderately elevated temperatures and $CO_2$ concentrations helped the biomass flourish as photosynthesis and water use efficiency increased, but huge increase in temperature ($above+4.0^{\circ}C$) has resulted in the increased respiration with increasing temperature. Consequently, Species productivity(Biomass) of trees decrease as the temperature is elevated drastically. It has been confirmed that the dominant species in all scenarios was Quercus mongolica. Like the trends shown in the changes of total AGB, it revealed the biggest increase in the AGB of Quercus mongolica under the RCP 4.5 scenario. AGB of Quercus mongolica and Quercus variabilis decreased in the RCP 4.5 and RCP 8.5 scenarios after 2050 but have much higher growth rates of the AGB starting from 2050 under the baseline scenario. Under all scenarios, the AGB of coniferous species was eventually perished in 2100. In particular they were extinguished in early stages of the RCP 4.5 and RCP 8.5 scenarios. This is because of natural selection of communities by successions and the failure to adapt to climate change. The results of the study could be expected to be effectively utilized to predict changes of the forest ecosystems due to climate change and to be used as basic data for establishing strategies for adaptation climate changes and the management plans for forest vegetation restoration in ecological restoration fields.

• Journal of Life Science
• /
• v.31 no.1
• /
• pp.52-58
• /
• 2021

Pseudomonas syringae pv. actinidiae, which causes bacterial canker in kiwifruit, is divided into five biovars (1, 2, 3, 5, 6) on the basis of genetic characteristics and toxin productivity. Among them, biovar 3 is responsible for the current global outbreak, and has been isolated in Korea since 2011. Biovar 3 strains isolated from Korea are subdivided into six genetically different lineages (subgroup I, IV, V, VI, VII, and VIII) based on random amplified polymorphic DNA (RAPD) analysis. In this work, the subgroup-specific sequence characterized amplified region (SCAR) primers were developed from sequenced differential RAPD bands. Distribution of the subgroups of the biovar 3 strains collected in Korea from 2011-2017 were examined using these subgroup-specific primer sets. Among the 54 strains tested, 35 strains (64.8%) belonged to subgroup V, 9 strains (16.7%) belonged to subgroup IV, 4 strains (7.4%) belonged to subgroup VI, 3 strains (5.6%) belonged to subgroup VII, 2 strains (3.7%) belonged to subgroup VIII, and 1 (1.9%) strain belonged to subgroup I. Strains belonging to subgroups IV, V, and VI were shown to be related to strains isolated from China, New Zealand, and Chile, respectively. The study revealed that the biovar 3 strains in Korea are genetically diverse and are estimated to have been introduced through pollen sourced from foreign countries.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.6
• /
• pp.583-590
• /
• 2021

This paper is a study on the digitization of an analog 3D pen. The term digital implies features such as homeostasis, transformability, combinability, reproducibility, and convenience of storage. One device that produces a combination of these digital characteristics is a 3D printer, but its industrial use is limited due to low productivity and limitations with materials and physical characteristics. In particular, improvements are required to use 3D printers, such as better user accessibility owing to expertise and skills in modeling software and printers. Complementing this fact is the 3D pen, which is excellent in portability and ease of use, but has a limitation in that it cannot be digitized. Therefore, in order to secure a digitalization capability and ease of use, and to secure the safety of printing materials that pose controversial hazards during the printing process, research problems and alternatives have been derived by combining food, and digitization was demonstrated with a newly developed 3D pen. In order to digitize the 3D pen, a sensor in a structured device detects the motion of an analog 3D pen, and this motion is converted into 3D data (X-Y-Z coordinate values) through a spatial analysis algorithm. To prove this method, the similarity was confirmed by visualization using MeshLab version 1.3.4. It is expected that this food pen can be used in youth education and senior healthcare programs in the future.

• Journal of Applied Biological Chemistry
• /
• v.64 no.1
• /
• pp.39-48
• /
• 2021

Droughts are one of the abiotic stresses that hinders the growth and productivity of crop plants. Coping with abiotic stress is necessary to understand the molecular regulatory networks that makes plants respond to adverse environmental conditions. In our experiment to find a combination that can cope with abiotic stress (respond to drought), we screened 5 stress-inducible promoters that are expressed only under stress conditions. This founded 36 cis-elements in stress-inducible promoters. With the result we designed 2 synthetic promoters (BL1, BL2) for fine-controlled regulation by assembling cis-elements from the native promoters, which are expressed only under stress caused by droughts. Analysis of the transgenic plant (BL1-GUS, BL2-GUS) showed that the synthetic promoters increased the expression of β-glucuronidase (GUS) in transgenic plants under desiccation. Also in the transient activation assay demonstrated that synthetic promoters induced the co-transformation of effector DREB1A and DREB2C. These results expect that the synthetic promoter with a combination of drought-specific elements can be used to respond to various abiotic stress and is resistant to stress without causing growth retardation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.119-125
• /
• 2020

Research on high-attenuation concrete for the vibration reduction performance by mixing epoxy-based synthetic resins and aggregates is actively being conducted. The curing time of high-attenuation concrete is very short because water is not used, and the physical and dynamic properties are very excellent. therefore, it is expected to be widely used in building structures requiring reduction of interior-floor noise and vibration. Furthermore, A way to expand the applicability of the high-damping concrete mixed with polymer in the field of reinforcement material have been variously studied. In order to replace polymer concrete with ordirnary concrete and existing anti-vibration reinforcement material, it is necessary to review overall vibration reduction performance considering physical properties, dynamic properties, productivity and field applicability. In this study, the physical and dynamic properties of polymer concrete by epoxy mixing ratio compared with ordirnary concrete. As a result, the elastic modulus was similar. On the other hand, polymer concrete for the compressive, tensile, and flexural strengths was quite more excellent. In particular, the measured tensile strength of polymer concrete was 4-10 times higher than that of ordirnary concrete. it was a big difference, and the frequency response function and damping ratio was studied through modal test and finite element analysis model. The dynamic stiffness of polymer concrete was 20% greater than that of ordirnary concrete, and the damping ratio of polymer concrete was approximately 3 times more than that of ordirnary concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.94-100
• /
• 2021

To improve the productivity of cargo containment construction for a membrane LNG carrier, it is important to shorten the installation period and process of the scaffolding system, which is a construction workbench of a cargo containment for a membrane LNG carrier. As an effective method, opinions are being gathered to enlarge the lifting unit from the existing two stages to eight stages. On the other hand, the stresses around the pin and hole will increase significantly because of the increase in lifting load according to the large size of the module. The purpose of this study was to establish a new large module-lifting plan by introducing TRIZ to solve these problems. This study adopted a method to utilize 40 inventive principles, which is one of the various problem-solving tools of TRIZ. First, technical contradictions were derived, the engineering parameters were selected. Second, efficient inventive principles were selected to overcome the technical contradictions using a contradiction matrix. Finally, the general and specific solutions were derived through the selected inventive principle, and structural analysis confirmed that the stress generated in the structure was low. The utility of TRIZ was confirmed by the successful lifting of large modules using the established lifting method.

• Korean Journal of Environmental Agriculture
• /
• v.40 no.1
• /
• pp.49-59
• /
• 2021

BACKGROUND: Soil salinity causes reduction of crop productivity. Rhizosphere microbes have metabolic capabilities and ability to adaptation of plants to biotic and abiotic stresses. Plant growth-promoting bacteria (PGPB) could play a role as elicitors for inducing tolerance to stresses in plants by affecting resident microorganism in soil. This study was conducted to demonstrate the effect of selected strains on rhizosphere microbial community under salinity stress. METHODS AND RESULTS: The experiments were conducted in tomato plants in pots containing field soil. Bacterial suspension was inoculated into three-week-old tomato plants, one week after inoculation, and -1,000 kPa-balanced salinity stress was imposed. The physiological and biochemical attributes of plant under salt stress were monitored by evaluating pigment, malondialdehyde (MDA), proline, soil pH, electrical conductivity (EC) and ion concentrations. To demonstrate the effect of selected Bacillus strains on rhizosphere microbial community, soil microbial diversity and abundance were evaluated with Illumina MiSeq sequencing, and primer sets of 341F/805R and ITS3/ITS4 were used for bacterial and fungal communities, respectively. As a result, when the bacterial strains were inoculated and then salinity stress was imposed, the inoculation decreases the stress susceptibility including reduction in lipid peroxidation, enhanced pigmentation and proline accumulation which subsequently resulted in better plant growth. However, bacterial inoculations did not affect diversity (observed OTUs, ACE, Chao1 and Shannon) and structure (principle coordinate analysis) of microbial communities under salinity stress. Furthermore, relative abundance in microbial communities had no significant difference between bacterial treated- and untreated-soils under salinity stress. CONCLUSION: Inoculation of Bacillus strains could affect plant responses and soil pH of tomato plants under salinity stress, whereas microbial diversity and abundance had no significant difference by the bacterial treatments. These findings demonstrated that Bacillus strains could alleviate plant's salinity damages by regulating pigments, proline, and MDA contents without significant changes of microbial community in tomato plants, and can be used as effective biostimulators against salinity stress for sustainable agriculture.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.66 no.1
• /
• pp.1-7
• /
• 2021

The processing of rice is one of the measures to expand the scope of rice use in response to the decrease in rice consumption. Since the main ingredient of rice processing is rice flour, "rice flour varieties" have been bred with the aim to improve the productivity and quality of rice flour. In order to study the variation in the ripening characteristics of rice flour varieties with respect to temperature, the average temperature after heading date was set at 28℃ (33/23℃), 22℃ (27/17℃), and 18℃ (23/13℃) inside the phytotron. We used Saenuri as non-glutinous rice variety, Seolgaeng as soft-type rice flour variety, and Baromi2 as powdered rice flour variety. At high temperatures (28℃), the grain weight of Baromi2 decreased by 21%. Its starch content also decreased by more than 10%, which was significantly lower than that of Saenuri and Seolgaeng. At low temperatures (18℃), the grain weight and starch content slightly increased or were similar in all varieties. An analysis of changes in the grain weight due to effective accumulated temperature through the sigmoid function showed that the velocity of grain-filling slowed significantly when Baromi2 was exposed to low temperature during the ripening stage compared to the other varieties. Therefore, the transplanting time of Baromi2 should be delayed to avoid high temperatures during the ripening stage. However, because the ripening period is not properly secured under low temperature conditions, grain filling may not be sufficient.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.23 no.2
• /
• pp.99-111
• /
• 2021

The connected farm that agricultural land, agricultural machinery and farmer are connected with an IoT gateway is in the commercialization stage. That has increased productivity, efficiency and profitability by intimate information exchange among those. In order to develop the educational program of intelligent agricultural machinery and the agricultural machinery safety education performance indicator, this study analyzed patent trends of agricultural machine with unmanned technology used in agriculture and efficiency technology applied advanced technologies such as ICT, robots and artificial intelligence. We investigated and analyzed patent trends in agricultural machinery of Korea, the USA and Japan as well as the countries in Europe. The United States is an advanced country in the field of unmanned technology and efficiency technology used in agriculture. Agricultural automation technology in Korea is insufficient compared to developed countries, which means rapid technological development is needed. In the sub-fields of field automation technology, path generation and following technology and working machine control technology through environmental awareness have activated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.639-647
• /
• 2022

The use of flames is essential in cutting, bending, and welding steel during a ship's construction process. While acetylene fuel is commonly used in steel cutting and the manufacturing process in shipyards, the use of propane as an alternative fuel has recently been increasing, due to the lower risk of explosion and propane's relatively low calorific value. However, propane fuel has a relatively slow processing speed and high slag generation frequency, thereby resulting in poor quality. Propylene is another alternative fuel, which has an excellent calorific value. It is expected to gain wider use because of its potential to improve the quality, productivity, and efficiency of steel processing. In this study, the combustion characteristics of propane and propylene fuel during steel plate processing were analyzed and compared. The reduction of greenhouse gases and other harmful gases when using propylene flame was experimentally verified by analyzing the gases emitted during the process. Heat distribution and tensile tests were also performed to investigate the effects of heat input, according to processing fuel used, on the mechanical strength of the marine steel. The results showed that when propylene was used, the temperature was more evenly distributed than when propane fuel was used. Moreover, the mechanical tests showed that when using propylene, there was no decrease in tensile strength, but the strain showed a tendency to decrease. Based on the study results, it is recommended that propylene be used in steel processing and the cutting process in actual shipyards in the future. Additionally, more analysis and supplementary research should be conducted on problems that may occur.