In this study, the environmentally friendly material charcoal was added to ricehusk, an agricultural by-product, and sawdust, which emerges during the sawing process, to produce board by mixing ratio and concentration levels of ricehusk and charcoal; it then investigated its physical properties for development purposes and achieved the following results. The water absorption and thickness swelling of the compounded board produced per adding ratio of ricehusk and charcoal showed a gradually decreasing tendency along with the increase in adding ratio of the charcoal, and as the density of the compounded board increased, the water absorption decreased, while the thickness swelling increased. The internal bond strength of the compounded board had indicated its highest value of 0.49N/㎟ at the density of 0.7g/㎤. This satisfied the quality standard for KSF 3104 Particleboard. The internal bond strength of the compounded board manufactured per adding ratio of ricehusk and charcoal showed a steady decrease with the decrease in the adding ratio of ricehusk, and an increase in the addingratio of the charcoal. Also, in cases when the ratio of the ricehusk and charcoal by KSF 3104 quality standard were 35:5 and 30:10, it satisfied the quality standard of 15.0-type, whereas it satisfied the 13.0-type quality standard if the ratios were 25:15 and 20:20. It showed a tendency of increasing hardness of the compounded board with the increase in density, and decreasing hardness with the increase in the adding ratio of the charcoal.
Kim, Hyun-bok;Seok, Young-Seek;Seo, Sang-Deok;Sung, Gyoo Byung;Kim, Sung-Kuk;Jo, You-Young;Kweon, HaeYong;Lee, Kwang-Gill
Journal of Sericultural and Entomological Science
/
v.53
no.2
/
pp.71-77
/
2015
Much attention has been focused on the activity of the natural antioxidants present in fruits and vegetables, because potentially these components may reduce the level of oxidative stress. Especially, mulberry leaves containing many natural components are considerable resource for natural antioxidants. The antioxidant capacity of mulberry leaves was investigated with minilum L-100 device and ARAW-KIT (anti-radical ability of water-soluble substance), in comparison to the ascorbic acid. The antioxidant capacity of 16 varieties was 3303.4 nmol at opening stage of five leaves in spring. The highest stage of antioxidant capacity (3708.0 nmol) and yield rate was just before the coloration stage with anthocyanin in fruits, whereas the lowest stage was middle of June (2231.6 nmol) and about two months growing stage after summer pruning (2064.6 nmol). But after summer pruning, the antioxidant capacity of mulberry leaves increased gradually until just before fallen leaves stage. Even if samples were same variety, antioxidant effect of those showed different results according to collected regions. Also, antioxidant effect of mulberry leaves were higher than that of branches. The antioxidant capacity of yield-type mulberry leaves and fruits (Morus alba L., M. bombycis Koidz, and M. Lhou (Ser.) Koidz) collected from In-je, Won-ju and Yang-yang regions, Kang-won province, Korea, was investigated. The results indicated that total antioxidant capacity of yield-type mulberry leaves was 2711.2 nmol. In the antioxidant capacity analysis of Jeollabuk-Do genetic resources, autumn's mulberry leaves showed higher antioxidant capacity than that of spring's it. To investigate the effect of tea on antioxidative capacity, five kinds of tea(coffee mix, green tea added brown rice, mulberry leaf tea, Polygonatum odoratum tea and black tea added lemon) were selected and analyzed. Their's anti-oxidative capacity were 2,531.01 nmol, 1,867.42 nmol, 1,053.72 nmol, 292.71 nmol and 188.91 nmol, respectively. The antioxidative capacity of drinking water soaked with mulberry leaf showed 891.96 nmol.
Journal of the Korea Academia-Industrial cooperation Society
/
v.20
no.4
/
pp.264-274
/
2019
This study attempted to analyze the effects of cleansing oil on skin by preferred vegetable base oil. For this, a questionnaire survey was performed against 100 people, and their face washing habit and preferred vegetable base oils were examined. Based on the results, 4 different cleansing oils were prepared and experimented. The experiment was conducted against 10 adult women in their 20-30s, and moisture level, sebum level and trans-epidermal water loss (TEWL) before and after the experiment were measured. After the test, satisfaction was measured, and the results found the followings: When asked what cleansing oil is most preferred by vegetable base oil type, 'rose hip oil' was the highest, followed by 'olive oil', 'apricot kernel oil' and 'camellia oil'. According to the clinical trials, both moisture and sebum levels increased before and after cleansing in all four cleansing oil types by the preferred vegetable base oil (p<0.001, p<0.001). In addition, TEWL decreased with a difference by base oil (p<0.01). According to a subjective satisfaction survey which was performed after the experiment, rose hip oil-contained cleansing oil (RHC) was the highest in terms of cleansing effect and satisfaction level. Consequently, it was confirmed that the cleansing oil by vegetable base oil improved skin conditions by protecting a skin barrier with a positive effect on the improvement of sebum and moisture levels and TEWL. Even though a preferred oil type and a satisfaction level may differ by preferred oil and feeling after use, cleansing oil by vegetable base can be helpful as a skin care product which eases skin dryness and protects a skin barrier.
Kim, Hyeon ju;Kim, Ji eun;Han, Yu bean;Choi, Seung hyun;Kang, Yun ki;Jung, Yu jin;Jung, Min young;Lee, Hoo min
Journal of the Korean Society of Radiology
/
v.12
no.6
/
pp.777-783
/
2018
The purpose of this study was to investigate the degree of tearing of the rubber when the spike of the syringe connector was connected to the bottle of the contrast medium composed of the rubber compound type and to investigate the presence of the synthetic rubber due to tearing and grinding and the size of the pulverized product when the pulverized matters rubber was detected. As a result, in the case of tearing degree, the front side of the first contact with the end of the syringe connector was torn more than the back side by about $3.14{\pm}0.04mm$, and the pulverized matters was detected on average 7 to 15 on the 10 contrast mediums. The average particle size was measured to be about $7.89{\pm}0.31{\mu}m$. In addition, it is necessary to develop a micro_filter type automatic injection system for blocking off the pulverized matters as well as additional experiments through various experiments and analysis methods, and it is considered that interest of related organizations will be needed in preparation of fatal accidents when pulverized matters is introduced.
KSCE Journal of Civil and Environmental Engineering Research
/
v.38
no.6
/
pp.967-977
/
2018
The problems of lack of skilled worker and poor productivity at the construction site continue to be raised, and the introduction of construction automation as one of the solutions to this has been considered. The development of various types of equipment and systems has been carried out, especially for earthwork operations with multiple construction equipment. However, the level of commercialization of developed equipment or systems is very limited. Although the single-product type of earthwork equipment has been applied to the site, the integrated type of earthwork system is still in the field testing stage. Considering these constraints, the limited budget and research period, a strategy is needed to identify which technology areas and core technologies should be developed first. In this study, the technology areas and detailed core technologies that are essential for the development of earthwork systems at the level of commercialization are set and the priority of development is determined. In addition, the earthwork system that has been developed so far is analyzed and the detailed development direction is presented based on it. The findings can be used for a decision making to set the priority for core technologies that should be developed first in the limited budget and period.
Journal of the Korean Recycled Construction Resources Institute
/
v.6
no.4
/
pp.267-274
/
2018
Though the wet bottom ash has been used as a type of lightweight aggregate, dry bottom ash, new type bottom ash from coal combustion power plant, has scarcely researched. It is excellent lightweight aggregate in the view point of construction material. This study is performed to check the applicability of dry bottom ash as a fine aggregate in lightweight aggregate concrete, by analyzing various properties of fresh and hardened concrete. We get results that the slump of concrete is within the target range at less than 75% replacement rate of dry bottom ash, the air content is not affected by the replacement rate of dry bottom ash, the bleeding capacity is less than $0.025cm^3/cm^2$ at 75% under of the replacement rate of dry bottom ash, and the compressive strength of concrete show 90% or more comparing the base mix while initial strength development is a little low. Oven dry unit weight of concrete is reduced by 8.9% when replaced 100% dry bottom ash, and dry shrinkage tends to decrease depending on increase of replacement rate of dry bottom ash. Modulus of elasticity of concrete shows no decease at 50% over of the replacement rate of dry bottom ash, while modulus of elasticity of concrete decreases when the replacement rate increases further. The dry bottom ash, when used as a fine aggregate in lightweight concrete, can be used effectively without any deterioration in quality.
This study was carried out to investigate fuel decomposition characteristics and coke formation according to types of endothermic fuels and methods of catalyst molding. Methylcyclohexane (MCH), n-dodecane, and exo-tetrahydrodipentadiene (exo-THDCP) were used as the endothermic fuels. As a catalyst, USY720 supported with platinum was used. It was manufactured by only using pressure to disk-type, or pelletized with a binder and a silica solution. The characteristics of the catalysts according to the molding method were analyzed by X-ray diffraction analysis, scanning electron microscopy, nitrogen adsorption-desorption isotherm, and ammonia temperature programmed desorption analysis. The reaction was carried out under conditions of high temperature and high pressure ($500^{\circ}C$, 50 bar) in which the fuel could exist in a supercritical state. The product was analyzed by gas chromatograph/mass spectrometer and the coke produced by the catalyst was analyzed by thermogravimetric analyzer. After the reaction, the composition of the products varied greatly depending on the structure of the fuel. In addition, the crystallinity and surface properties of the catalysts were not changed by the method of catalyst molding, but the changes of the acid sites and the pore characteristics were observed, which resulted in changes in the amount and composition of products and coke.
Journal of the Korean Society for Library and Information Science
/
v.57
no.2
/
pp.435-452
/
2023
This study experimented with automatic classification of subject headings using BERT-based transfer learning model, and analyzed its performance. This study analyzed the classification performance according to the main class of KDC classification and the category type of subject headings. Six datasets were constructed from Korean national bibliographies based on the frequency of the assignments of subject headings, and titles were used as classification features. As a result, classification performance showed values of 0.6059 and 0.5626 on the micro F1 and macro F1 score, respectively, in the dataset (1,539,076 records) containing 3,506 subject headings. In addition, classification performance by the main class of KDC classification showed good performance in the class General works, Natural science, Technology and Language, and low performance in Religion and Arts. As for the performance by the category type of the subject headings, the categories of plant, legal name and product name showed high performance, whereas national treasure/treasure category showed low performance. In a large dataset, the ratio of subject headings that cannot be assigned increases, resulting in a decrease in final performance, and improvement is needed to increase classification performance for low-frequency subject headings.
Optimal winterizing condition of com oil was cooling temperature of bleached oil from $105^{\circ}C$ to $40^{\circ}C$. Then, filtering it after keeping $1{\sim}2^{\circ}C$ by lowering the temperature gradually with treating perlite of 0.3%(w/w) amount about bleached oil and stirring. We could measure that triglyceride(TG) that extracted from lipid components from spent perlite(SP) obtained through filtration after winterizing by SACC method is major causing materials of clouding in com oil. The result of separating TG fraction by agentation TLC was that it classified into 4 kinds -U3, SU2, S2U, S3 type and the most were U3 type. From this, it's easy to identify cause of clouding in com oil is TG fraction and most of them form wax materials that can observed. The results were they kept clear appearance at $0^{\circ}C$ generally during 39.6 to 96.5 hours, especially the result of A sample that had the lowest temperature condition while they have some difference by condition of treating temperature.
Asia-Pacific Journal of Business Venturing and Entrepreneurship
/
v.19
no.3
/
pp.69-79
/
2024
Companies should resolve consumer dissatisfaction and increase brand loyalty by actively identifying the factors of consumer dissatisfaction and proactively responding to expected complaint behavior to induce repurchase. This is a management goal that should be pursued in common regardless of the size of the company. The specific purpose of this study is to find out whether the degree of dissatisfaction differs depending on whether or not consumers' expected performance before purchase and the actual perceived performance after purchase is compared, whether the degree of dissatisfaction affects the type of complaint behavior, which is a subsequent behavior, and whether the attributable behavior has a moderating effect in this process and whether the persistence of the result and the controllability of the cause act as a factor that determines the attribution position. In particular, compared to general companies, venture companies are more likely to overload the information processing ability of managers and are likely to make various irrational errors in decision making, so this study has important academic and practical implications. As a result of the analysis, the negative inconsistency group had the highest degree of dissatisfaction, and the higher the degree of inconsistency, the higher the dissatisfaction. The attributable behavior of unsatisfied consumers had a moderating effect on the degree of dissatisfaction, and the dissatisfaction was significantly higher in the external attributable group than the internal attributable group, which was statistically significant. On the other hand, the persistence of the result had a statistically significant effect on the attribution position, but the controllability of the cause was not. The degree of attributable behavior and dissatisfaction did not affect the type of complaining behavior, showing limited influence. Along with the interpretation of these results, this study presents various implications, especially for small and medium-sized/venture companies that provide new durable products.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.