• Membrane Journal
• /
• v.19 no.3
• /
• pp.252-260
• /
• 2009

The effects of the treatment of an acidic solution at pH 2 on polyacrylonitrile ultrafiltration (UF) membranes were investigated using a circular cross-flow filtration bench with a membrane module. A substantial reduction in the membrane permeability was observed after 80 hours' treatment of the acidic solution. In addition, the analyses of the sample solutions by ultraviolet/visible absorption spectroscopy and gas chromatography/mass spectrometry (GC/MS), which were taken from the feed tank as a function of the treatment time, showed that a new organic compound was produced in the course of the treatment. From a thorough search of the mass spectral library we presumed the new compound to be 1,6-dioxacyclododecane-7,12-dione (DCD), one of the well-known additives for polyurethane. Based on further experimental results, including the scanning electron microscope (SEM) images and the solid-state NMR spectra of the membranes used for the treatment of the acidic solution, we suggested that the decrease of the permeate flux resulted not from the deformation of the membranes, but from the fouling by DCD eluted from the polyurethane tubes in the filtration bench during the treatment. Those results imply that the reactivity to an acidic solution of the parts comprising the filtration bench is as important as that of the membranes themselves for effective treatments of acidic solutions, for efficient chemical cleaning by strong acids, and also in determining the pH limit of the solutions that can be treated by the membranes.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.171-187
• /
• 2006

The status of heavy metal contamination was investigated using chemical analyses of stream waters and sediments obtained from Samsanjeil and Sambong Cu mining area in Goseong-gun, Gyeongsangnam-do. In addition, the degree and the environmental risk of heavy metal contamination in stream sediments was assessed through pollution index (Pl) and danger index (DI) based on total digestion by aqua regia and fractionation of heavy metal contaminants by sequential extraction, respectively. Not only the degree of heavy metal contamination was significantly higher in Samsanjeil area than in Sambong area, but its environmental risk was also revealed much more serious in Samsanjeil area than in Sambong area. The differences in status and level of contamination and environmental risk between both two mining areas may be attributed to existence of contamination source and geology. Acid mine drainage is continuously discharged and flows into the stream in Samsanjeil mining area, and it makes the heavy metal contamination in the stream more deteriorated than in Sambong mining area in which acid mine drainage is not produced. In addition, the geology of Samsanjeil mining area is mainly comprised of andesitic rocks including a small amount of calcite and having lower pH buffering capacity fer acid mine drainage, and it is likely that the heavy metal contamination cannot be naturally attenuated in streams. On the contrary, the main geology of Sambong mining area consists of pyroclastic sedimentary Goseong formation containing a high content of carbonates, particularly calcite, and it seems that these carbonates of high pH buffering capacity prevent the heavy metal contamination from proceeding downstream in stream within that area.

• Journal of Animal Science and Technology
• /
• v.48 no.2
• /
• pp.219-226
• /
• 2006

The wastes (the needle leaves and branches) produced from thinning the forest were fermented under an anaerobic condition (pine silage) to utilize as a forage source of ruminants. An in situ trial was conducted with two ruminally fistulated Korean native cows by 4 replicates (2 bags per cow), and in vivo digestibility of pine silage was estimated with five Korean native steers by 5 replicates in incomplete double turn-over design. In order to investigate feed efficiency and carcass traits, forty eight Korean native bulls were assigned to four treatments (0%, 25%, 50%, 75% of pine silage) with a completely randomized design in 12 pens accommodating 4 animals per pen. The amounts of concentrate and roughage allowed to experimental animals were in the range of 2.5% and 0.6% of body weight, respectively. Animals had freely accessed to mineral block and water in stanchion barn.An in situ crude protein digestibility of the roughage sources when suspended for 48 hrs in the rumen was higher for feeding the pine silage than the rice straw, whereas NDF digestibility was vice versa. No differences between the treatments were observed in in vivo digestibilities of dry matter, crude protein and NDF. Daily body weight gain was significantly (P<0.01) higher for the pine silage substitutions compared with the rice straw feeding except for the 25% silage feeding. The pine silage feeding did not affect feed efficiency.In carcass traits, marbling score tended to be higher for the 50% pine silage treatment than the other treatments while back fat thickness tended to be the thinnest for the rice straw feeding. From these results, it may be recommended to substitute pine silage, as a forage source, for rice straw by 50 percent.

• Korean Journal of Environmental Agriculture
• /
• v.19 no.1
• /
• pp.51-57
• /
• 2000

Waste newspapers was used as an amendment to adjust the moisture of household food wastes for composting. The mixture of household food wastes and waste newspapers was composted in an especially designed small home composter, where the early fed composting materials were discharged early. The temperature inside composting materials was influenced very much by that of outside, because the composter was not insulated. Accordingly, the higher the outside temperature was, the higher the decomposition rate was. The temperature inside composting materials did not reach to optimum, because the amount of composting materials added in the composter everyday was too little, and it caused too high water content of discharged compost after 15 weeks. Therefore, it was required that the composter must be insulated to maintain the higher temperature. The inorganic compounds$(K_2O,\;CaO,\;MgO,\;P_2O_5)$ and heavy metals(Zn, Cu, Cr, Cd, Hg, As) were accumulated obviously in produced compost, when dry recycled compost was reused as the amendment for adjusting the moisture.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.2
• /
• pp.113-118
• /
• 2017

BACKGROUND: The carbon (C) isotope ratio (${\delta}^{13}C$) of dissolved organic C (DOC) is an indicator of water pollution source. In this study, the potential use of two pre-treatments for the ${\delta}^{13}C$ analysis, alkaline persulfate oxidation coupled with carbonate precipitation (precipitation) and freeze drying (drying), were compared to suggest a more feasible pre-treatment method. METHODS AND RESULTS: Two reference materials with different ${\delta}^{13}C$ values were used for the experiments; chemical grade glucose ($-12.0{\pm}0.02$‰) and pig manure compost extract ($-23.3{\pm}0.04$‰). In the precipitation method, the measured ${\delta}^{13}C$ values were consistently lower than the theoretically calculated values as dissolved $CO_2$ could not be removed due to the alkaline property of the reagents and the dissolution of air $CO_2$ into the alkaline solution. The drying method also resulted in more negative ${\delta}^{13}C$ than the calculated ${\delta}^{13}C$; however, the difference was systematic ($3.9{\pm}0.3$‰) and there was a strong correlation (${\delta}^{13}C_{calculated}=0.87{\times}{\delta}^{13}C_{measured}-0.624$, $r^2=0.98$) between the calculated and measured ${\delta}^{13}C$. Calibration of ${\delta}^{13}C$ using the relationship between the calculated and the measured ${\delta}^{13}C$ values produced reliable and accurate ${\delta}^{13}C$ values. CONCLUSION: Our results suggest that the drying method is more accurate pre-treatment method to minimize the influence of air $CO_2$ compared to the precipitation method for the determination of ${\delta}^{13}C$ of DOC.

• Journal of Food Hygiene and Safety
• /
• v.25 no.1
• /
• pp.36-42
• /
• 2010

The method for the determination of ethylenediamine (EDA) and hexamethylenediamine (HMDA) in food simulants was developed, and migration amounts of these compounds was monitored for 124 polyamide (PA) utensils. The diurethane derivatives of EDA and HMDA, which produced by reaction with ethyl chloroformate, were analyzed by using gas chromatograph (GC)/flame ionization detector (FID) and GC/mass spectrometer (MS). The developed method was validated with $0.3\;{\mu}g/mL$ of limit of detection (LOD) for EDA and $0.1\;{\mu}g/mL$ of LOD for HMDA, > 0.999 of linearity($r^2$) and > 88% of recovery. The EDA was detected 1.31 and $02.06\;{\mu}g/mL$ for 2 samples in water. The HMDA was detected $0.29\;-\;0.93\;{\mu}g/mL$ for 3 samples in 20% ethanol and $0.26\;-\;0.44\;{\mu}g/mL$ for 10 samples in n-heptane. These migration levels were below the specific migration limits (SML) of $12\;{\mu}g/mL$ and $2.4\;{\mu}g/mL$ for EDA and HMDA established in EU.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.58 no.3
• /
• pp.324-330
• /
• 2013

One of the abundant biomass for bioenergy production is thought to be agricultural by-products produced annually. The purpose of this study were to provide basic information about the changes of the moisture contents and chemical compositions for storage periods and bale types of rice straw, and it was attempted for the first time. The bale types of rice straw which were harvest in October 2011, were the square bale, the round bale, and the wrapped round bale type with plastic, respectively. Each of bale were stored in house, outdoor, and rain sheltering facilities condition for 1 year. The moisture contents and chemical compositions for each bale type are investigated for the 3-storage stages (0, 6, 12 month). While the moisture contents of the square and round bales stored in house condition were ranged from 20~25%, the square bale stored under the rain shelter facilities was showed the lowest moisture content less than 20% during the storage periods. For the chemical compositions, the cellulose and hemicellulose contents of rice straw bale stored in outdoor condition were decreased with the storage periods. However, in house condition, the chemical compositions of the square and round bales were slightly increased at the middle and the end of storage stages (6 and 12 months) compared with the initial storage stage (0 month). In conclusion, while optimum and favorable storage conditions of agricultural by-products is a house storage of the bale with plastic, if the bale can stored at outdoor, water penetration prevention such as the rain shelter facilities is required.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.2
• /
• pp.97-105
• /
• 2009

A constructed wetland which was composed of aerobic and anaerobic areas was evaluated for 3 years to effectively treat the sewage produced in farming and fishing communities. For 3 years in a constructed wetland, biochemical oxygen demand(BOD), chemical oxygen demand(COD), suspended solids(SS), total nitrogen(T-N), and total phosphorus(T-P) in effluent were 0.2${\sim}$11.8, 1.0${\sim}$41.9, 1.1${\sim}$6.5, 4${\sim}$60 and 0.02${\sim}$3.51 mg/L, respectively. Removal rate of BOD, COD and SS in effluent were 97, 92 and 99%, respectively, in the third year. As time goes by, removal rate of T-N and T-P in treated water in aerobic area and effluent were gradually increased in a constructed wetland. In the third year, removal rate in effluent were 62 and 73%, respectively. By the seasons, removal rate of BOD, COD, SS, T-N and T-P were 97${\sim}$98, 87${\sim}$91, 99, 43${\sim}$61 and 76${\sim}$86%, respectively. Removal rate of BOD, COD, SS and T-P were not affected by the seasons, but that of T-N in winter and spring were decreased than the other seasons.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.483-489
• /
• 2006

The behavior of rare earth compounds such as $La_{2}O_{3}$, $CeO_{2}$, and $Ca(OH)_{2}$ on the removal of fluoride and heavy metals in the steel wastewater has been investigated. The removal mechanism of fluoride by rare earth elements has been known to be the formation of insoluble compounds between $F^{-}$ and cations such as $La^{3+}$ and $Ce^{4+}$ produced by the dissociation of rare earth compounds (To reduce the running cost of the fluoride wastewater treatment facility, their fluoride removal efficiencies were compared with those of inexpensive rare earth minerals such as natural lanthanide and cerium compound used as a glass polishing agent). All of the rare earth oxides used in this study showed a higher removal efficiency of fluoride than $Ca(OH)_{2}$ in the wastewater. In the case of artificial HF solution, the removal efficiency of fluoride showed in the order: $CeO_{2}$-mineral < $CeO_{2}$ < $Ca(OH)_{2}$ < $La_{2}O_{3}$-mineral < $La_{2}O_{3}$. However, the removal efficiency of fluoride in the wastewater increased in the following order: $Ca(OH)_{2}$ < $CeO_{2}$ mineral < $CeO_{2}$ < $La_{2}O_{3}$ mineral < $La_{2}O_{3}$. All agents showed high efficiencies for the removal of Mn and total Cr in the rare earth compounds. In the case of $Ca(OH)_{2}$, fluoride removal decreased with increasing pH while. However, the rare earth compounds showed a higher fluoride removal in higher pH condition, the optimum pH condition seemed to be around 7 considering both water quality and fluoride removal. Under the pH 7 condition, the $Ca(OH)_{2}$ was superior to rare earth compounds in Mn removal and the lanthanide was superior to others in total Cr removal.

• The Korean Journal of Food And Nutrition
• /
• v.14 no.5
• /
• pp.457-466
• /
• 2001

In this study. HACCP system was applied to improve the quality of instant ablactation baby food with rising sanitary problem among SunSig(powder of roasted grains and vegetables) . It took about 9min 30 second to produce and the temperature status of raw materials were 30.9∼31.8$\^{C}$. Raw material and production phase goods had average 6.2 in pH and 0.23∼0.63 in water activity. The average number of total aerobic bacteria(TAB) and coliform were 1.4$\times$10$^4$ CFU/g, 5.5$\times$10 CFU/g in raw materials. And the number became 8.7$\times$10$^2$ CFU/g, 6.9$\times$10 CFU/g after 1st grinding step. The distributions of TAB and coliform in equipments were 3.8$\times$10$^4$ CFU/㎠, 8.0$\times$10 CFU/㎠ on the average. According to storage temperature, variations of number of TAB coliform were slight at 4$\^{C}$ but increased at 20$\^{C}$ and 30$\^{C}$ . Therefore following subjects can be issued on the basis of results. Minimize the storage time and keep at cool temperature. 1st and 2nd grinders should be managed hygienically. Establish the heating step during the production of instant action baby food. Instant ablactation baby food produced should be stored at cool and freeze condition.