• Composites Research
• /
• v.24 no.1
• /
• pp.45-50
• /
• 2011

Transparent and conductive carbon nanotube on polyethylene terephthalate (PET) were prepared by dip-coating method for self-sensing multi-functional nanocomposites. The changes in the electrical and optical properties of CNT coating mainly depended on the number of dip-coating, concentration of CNT solution. Consequently, the surface resistance and transmittance of CNT coating were sensitively controlled by the processing parameters. Surface resistance of CNT coating was measured using four-point method, and surface resistance of coated CNT could be better calculated by using the dual configuration method. Optical transmittance of PET film with CNT coating was evaluated using UV spectrum. Surface properties of coated CNT investigated by wettability test via static and dynamic contact angle measurement were consistent with each other. As dip-coating number increased, surface resistance of coated CNT decreased seriously, whereas the transmittance exhibited little lower due to the thicker CNT networks layer. Interfacial microfailure properties were investigated for CNT and indium tin oxide (ITO) coatings on PET substrates by electrical resistance measurement under cyclic loading fatigue test. CNT with high aspect ratio exhibited no change in surface resistance up to 2000 cyclic loading, whereas ITO with brittle nature showed a linear increase of surface resistance up to 1000 cyclic loading and then exhibited the level-off due to reduced electrical contact points based on occurrence of many micro-cracks.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.119-120
• /
• 2002

The aim is to urge the need of elaborate commissioning of 3D RTP system from the firsthand experience. A 3D RTP system requires so much data such as beam data and patient data. Most data of radiation beam are directly transferred from a 3D dose scanning system, and some other data are input by editing. In the process inputting parameters and/or data, no error should occur. For RTP system using algorithm-bas ed-on beam-modeling, careless beam-data processing could also cause the treatment error. Beam data of 3 different qualities of photon from two linear accelerators, patient data and calculated results were commissioned. For PDD, the doses by Clarkson, convolution, superposition and fast superposition methods at 10 cm for 10${\times}$10 cm field, 100 cm SSD were compared with the measured. An error in the SCD for one quality was input by the service engineer. Whole SCD defined by a physicist is SAD plus d$\sub$max/, the value was just SAD. That resulted in increase of MU by 100${\times}$((1_d$\sub$max//SAD)$^2$-1)%. For 10${\times}$10 cm open field, 1 m SSD and at 10 cm depth in uniform medium of relative electron density (RED) 1, PDDs for 4 algorithms of dose calculation, Clarkson, convolution, superposition and fast-superposition, were compared with the measured. The calculated PDD were similar to the measured. For 10${\times}$10 cm open field, 1 m SSD and at 10 cm depth with 5 cm thick inhomogeneity of RED 0.2 under 2 cm thick RED 1 medium, PDDs for 4 algorithms were compared. PDDs ranged from 72.2% to 77.0% for 4 MV X-ray and from 90.9% to 95.6% for 6 MV X-ray. PDDs were of maximum for convolution and of minimum for superposition. For 15${\times}$15 cm symmetric wedged field, wedge factor was not constant for calculation mode, even though same geometry. The reason is that their wedge factor is considering beam hardness and ray path. Their definition requires their users to change the concept of wedge factor. RTP user should elaborately review beam data and calculation algorithm in commissioning.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.2
• /
• pp.52-59
• /
• 2008

The objective of this study is to develop an automatic object changer unit to improve processing problems existed in the conventional horizontal machining center. To achieve this goal, this study designed a horizontal transfer as the second project continued to the first project that designed a upward and downward traverse unit. A horizontal traverse unit shows a symmetric structure and consists of frame, which consists of four unit tools, motor and reducer, which are fixed at a frame, operation unit with pinions, first traverse unit, and second traverse unit. Constraint conditions based on the operation mechanism with these elements were configured and obtained following results after modeling a model for a traverse motor. In the kinematic expression of sliding motion with one degree of freedom, the sliding motion is constrained. Also, the rack 3 installed at a frame is used to configure possible kinematic constraint conditions of the rack 2 according to the rolling motion of the pinion 2 in the first traverse unit. In addition, the moment of inertia that is a type of kinetic energy in a converted horizontal traverse unit in the side of the reducer can be applied to introduce the moment of inertia of a converted horizontal traverse unit in the side of the reducer by using the sum of kinetic energy in the rack and pinion, which is a part of the horizontal traverse unit. Also, the equation of motion of the converted upward and downward traverse unit in the side of the motor using the equation of motion of the motor. Furthermore, the horizontal traverse unit predetermines the mass of the first and second traverse unit and applied load including the radius and reduction ratio of the pitch circle in the pinion 1 and applied load to the rack 2. Then, a proper motor can be determined using several parameters in the upward and downward traverse unit in order to verify such predetermined specifications. In future studies later this study, a simulation that verifies the results of the previous two stages of studies using a finite element method.

• Geophysics and Geophysical Exploration
• /
• v.19 no.1
• /
• pp.11-19
• /
• 2016

Two representative residual static methods of traveltime decomposition and stack-power maximization are discussed in terms of application to land seismic data. For the model data with synthetic shot/receiver statics (time shift) applied and random noises added, continuities of reflection event are much improved by stack-power maximization method, resulting the derived time-shifts approximately equal to the synthetic statics. Optimal parameters (maximum allowable shift, correlation window, iteration number) for residual statics are effectively chosen with diagnostic displays of CSP (common shot point) stack and CRP (common receiver point) stack as well as CMP gather. In addition to removal of long-wavelength time shift by refraction statics, prior to residual statics, processing steps of f-k filter, predictive deconvolution and time variant spectral whitening are employed to attenuate noises and thereby to minimize the error during the correlation process. The reflectors including horizontal layer of reservoir are more clearly shown in the variable-density section through repicking the velocities after residual statics and inverse NMO correction.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.9
• /
• pp.1247-1255
• /
• 2016

Heparin binding proteins (HBPs) are produced by accessory glands. These are secreted into the seminal fluid, bind to the spermatozoa at the time of ejaculation, favour capacitation, acrosome reaction, and alter the immune system response toward the sperm. The present study was conducted with an objective to assess the effect of purified seminal plasma-HBPs (SP-HBPs) on cross bred cattle bull sperm attributes during two phases of cryopreservation: Pre freezing and freezing-thawing. SP-HBPs were purified from pooled seminal plasma by heparin affinity chromatography. Three doses of SP-HBPs i.e. 10, 20, $40{\mu}g/mLs$ semen were standardized to find out the optimum dose and $20{\mu}g/mLs$ was found to be an optimum dose. Semen as such and treated with SP-HBPs was diluted with sodium citrate-egg yolk diluter and cryopreserved as per the standard protocol. Sperm parameters i.e. motility, viability, Hypo-osmotic swelling test (HOST), acrosome damage, in vitro capacitation and lipid peroxidation were evaluated in SP-HBP treated and untreated (control) semen at both phases of cryopreservation. A considerable variation in percent sperm motility, viability, membrane integrity (HOST), acrosome damage, acrosome reaction and lipid peroxidation was observed at both phases among the bulls irrespective of the treatment. Incubation of neat semen with $20{\mu}g/mL$ SP-HBP before processing for cryopreservation enhanced the average motility, viability, membrane integrity by 7.2%, 1.5%, 7.9%, and 5.6%, 6.6%, 7.4% in pre-frozen and frozen-thawed semen in comparison to control. There was also an average increase of 4.1%/3.9% in in vitro capacitation and acrosome reaction in SP-HBPs-treated frozen-thawed semen as compared to control. However, binding of SP-HBPs to the sperm declined acrosome damage and lipid peroxidation by 1.3%/4.1% and 22.1/$32.7{\mu}M$/$10^9$ spermatozoa in SP-HBP treated pre-frozen/frozen-thawed semen as compared to control, respectively. Significant (p<0.05) effects were observed only in motility, HOST and in vitro acrosome reaction. It can be concluded that treatment of neat semen with SP-HBPs before cryopreservation minimized the cryoinjury by decreasing the generation of reactive oxygen species.

• The Journal of the Korea Contents Association
• /
• v.13 no.11
• /
• pp.902-912
• /
• 2013

This study on the training of police officers job satisfaction and job performance is to identify the relationship. This study of 2012 Police Training Institute courses in related expenses 5 population in the process of initiation of a national police officer selection, and note that the sampling method used to extract a total of 300 samples, but the number of cases that were used in the final analysis, 268 people. Data processing by the SPSSWIN 18.0 factor analysis, reliability analysis, multiple regression, path analysis. Conclusions are as follows. First, the police officer's training affects job satisfaction. In other words, work-related, of course the more positive the evaluation of job training job satisfaction is high, education, the stronger the motivation and job satisfaction also higher education can be. Second, the education and training of police officers affects job performance. In other words, work-related, educational motivation, job training curriculum for the more positive job performance rating is also high. Third, the police officer's job satisfaction affects job performance. In other words, education can be a higher job performance and job satisfaction also high. Fourth, the training of police officers on the job satisfaction and job performance directly or indirectly affected. That is, the internal job satisfaction and job performance, job training parameters are the important variables.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.646-651
• /
• 2018

This paper reports that the electronic properties at a $P3HT/TiO_2$ interface associated with exciton dissociation and transport can be tailored by the insertion of a graphene quantum dot (GQD) layer. For donor/acceptor interface modification in an $ITO/TiO_2/P3HT/Al$ photovoltaic (PV) device, a continuous GQD film was prepared by a sonication treatment in solution that simplifies the conventional processes, including laser fragmentation and hydrothermal treatment, which limits a variety of component layers and involves low cost processing. The high conductivity and favorable energy alignment for exciton dissociation of the GQD layer increased the fill factor and short circuit current. The origin of the improved parameters is discussed in terms of the broad light absorption and enhanced interfacial carrier transport.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.4
• /
• pp.640-650
• /
• 2020

Objective: Although the slaughter of cull sows (CS) for human consumption and meat products processing appears quite common throughout the world, relatively limited scientific information regarding the meat quality parameters of this pork type is available. The present study aimed at providing the technological quality characteristics and eating quality of CS meat, and comparing with those of commercial pork. Methods: Longissimus thoracis et lumborum muscle samples of CS and finisher pigs (FP) at 24 h postmortem were collected and used for investigation of the meat quality traits (pH, color, shear force, cooking loss, water holding capacity), fatty acids, flavor compounds and sensory characteristics. Results: The CS meat had significantly higher moisture content (p = 0.0312) and water holding capacity (p = 0.0213) together with lower cooking loss (p = 0.0366) compared to the FP meat. The CS meat also exhibited higher (p = 0.0409) contents of unsaturated fatty acids, especially polyunsaturated fatty acids (PUFA, p = 0.0213) and more desirable PUFA/total saturated fatty acids ratio (p = 0.0438) compared to the FP meat. A total of 56 flavor compounds were identified, amongst the amount of 16 compounds differed significantly between the two pork groups. Most of the PUFA-derived flavor compounds (e.g., hexanal, benzaldehyde, and hydrocarbons) showed higher amounts in the CS meat. While, 3-(methylthio)-propanal and 4-methylthiazole associated with pleasant aromas (meaty and roast odor notes) were only found in the FP meat. Furthermore, no differences were reported by panelists for flavor, juiciness, tenderness, and acceptability scores between the two pork groups studied. Conclusion: The sow meat exhibited better technological quality and its eating quality could be comparable to the commercial pork. This study provides meat processors and traders with valuably scientific information which may help to improve the utilization and consumption level of sow meat.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.6
• /
• pp.437-445
• /
• 2004

In this paper. we describe a novel method for transforming audio contents according to user's preference on sound field. Sound field effect technologies. which transform or simulate acoustic environments as user's preference, are very important for enlarging the reality of acoustic scene. However huge amount of computational power is required to process sound field effect in real time. so it is hard to implement this functionality at the portable audio devices such as MP3 player. In this paper, we propose an efficient method for providing sound field effect to audio contents independent of terminal's computational power through processing this functionality at the server using user's sound field preference, which is transfered from terminal side. To describe sound field preference, user can use perceptual acoustic parameters as well as the URI address of room impulse response signal. In addition, a novel fast convolution method is presented to implement a sound field effect engine as a result of convoluting with a room impulse response signal at the realtime application. and verified to be applicable to real-time applications through experiments. To verify the evidence of benefit of proposed method we performed two subjective listening tests about sound field descrimitive ability and preference on sound field processed sounds. The results showed that the proposed sound field preference can be applicable to the public.

• The KIPS Transactions:PartD
• /
• v.13D no.4 s.107
• /
• pp.463-476
• /
• 2006

R-trees have been traditionally optimized for the I/O performance with the disk page as the tree node. Recently, researchers have proposed cache-conscious variations of R-trees optimized for the CPU cache performance in main memory environments, where the node size is several cache lines wide and more entries are packed in a node by compressing MBR keys. However, because there is a big difference between the node sizes of two types of R-trees, disk-optimized R-trees show poor cache performance while cache-optimized R-trees exhibit poor disk performance. In this paper, we propose a cache and disk optimized R-tree, called the PR-tree (Prefetching R-tree). For the cache performance, the node size of the PR-tree is wider than a cache line, and the prefetch instruction is used to reduce the number of cache misses. For the I/O performance, the nodes of the PR-tree are fitted into one disk page. We represent the detailed analysis of cache misses for range queries, and enumerate all the reasonable in-page leaf and nonleaf node sizes, and heights of in-page trees to figure out tree parameters for best cache and I/O performance. The PR-tree that we propose achieves better cache performance than the disk-optimized R-tree: a factor of 3.5-15.1 improvement for one-by-one insertions, 6.5-15.1 improvement for deletions, 1.3-1.9 improvement for range queries, and 2.7-9.7 improvement for k-nearest neighbor queries. All experimental results do not show notable declines of the I/O performance.