• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2001.06a
• /
• pp.117-120
• /
• 2001

Deadbeat property is well established in digital control system design, But in continuous time, it can hardly realized for it's asymtotic property. But recently japanese researchers suggested serveral method for continuous time deadbeat property. They use delay elements In polynomials and established for the deadbeat condition. By solving this condition, unknown coefficients in polynomials with delay elements is obtained. In this paper, design method for optimal continuous time deadbeat servo system using 2nd order smooting elementsis studied. Continuous time deadbeat controller is consisted of serial integral compensator and local feedback one in state feedback loop. Determining method for damping rations and natural frequencies of smothing elements is described. By computer simulations, control inputs and system outputs are shown to have desirable property such as smoothness.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.2
• /
• pp.12-20
• /
• 2007

The aiming ability is a key to improve the accuracy performance of the gun pointing system in the ground military vehicle. This paper describes the new detection method of chatter vibration using disturbance acceleration in the pointing structure. In order to analysis the vibration trends of the pointing system occurred while the vehicle driving, acceleration data obtained from vehicle was processed by using data processing algorithm with moving average and Hilbert transform. The specific mode constants of acceleration were obtained from various disturbances. Vehicle velocity, road condition and property of pointing structure were considered as factors which make the change of vibration trend in vehicle dynamics. Finally, back propagation neural networks have been applied to the pattern recognition of the classification of vibration signal in various driving conditions. Results of signal processing were compared with other condition result and analysed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.1
• /
• pp.14-20
• /
• 2016

The accurate analysis of the outside sky conditions is necessary to increase the efficiency of blind PV system. To conduct the accurate analysis, this paper suggested a method to analyze the sky condition using a specific image processing technique. While a fisheye lens has a wide field-of-views, it causes a large distortion to the sky images. Therefore, this paper calculated the exchange ratio of sky images to consider a lens distortion. As results of the study, there was a difference of 7% to cloud area ratio F4 and F11. Also, it had a different result depending on the position of the cloud.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.883-886
• /
• 2005

This paper proposed a wireless measurement system (WMS) for an effective condition monitoring using wireless communication. WMS consists of two parts: transmitter(TM) acquired a dynamic signal from physical system using ICP type accelerometer sensor. An acquired signal modulated through the low/high pass filter and amplifier in DAQ board, which converted to digital signal. Embedded board(E-board) transferred digital signals to base station(BS) through the socket IEEE.802.11.b. BS is adopted IOCP server structure. Because it can acquired signal well during transferred digital signal. Signal processing used LabVIEW Library, BS(server) designed to realize multi-thread using visual C++.NET for 1 many meaning data processing

• Proceedings of the Korea Information Processing Society Conference
• /
• 2011.04a
• /
• pp.269-272
• /
• 2011

프로그램 신뢰성을 높이기 위한 방법 중 하나로 쓰이는 것이 명세 된 언어의 검증이다. 명세 된 언어를 검증하기 위해 소스 프로그램을 논리식으로 바꾸어 검증하는 방법을 사용한다. 소스 프로그램 뿐만 아니라 바이트코드 역시 프로그램 신뢰성을 높이기 위해서 검증이 필요하다. 본 논문에서는 바이트 코드의 검증을 위해 바이트코드의 정보를 가지고 있는 중간언어의 verification condition을 생성하는 방법을 보인다.

• Journal of Korea Foundry Society
• /
• v.29 no.2
• /
• pp.86-94
• /
• 2009

The effect of austenitizing temperature and time on the processing window of 3.60wt%C - 2.50wt%Si - 0.80wt%Cu ductile cast iron and that of the amount of copper added were investigated. The second stage reaction at 400oC was retarded with increased austenitizing temperature. The widest processing window was obtained at the lower austempering temperature with the increased time at the same austenitizing temperature. The width of the widest processing window was decreased with the increase of time at the same austenitizing temperature. The width of processing window was increased with the increased amount of copper added.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2003.05a
• /
• pp.85-86
• /
• 2003

As seafood processing by-products, enormous seafood processing waste waters (SPWWs) are produced at most seafood processing plants, but management of these waste waters are becoming great burden at small capacity processing plant. Hence, almost of them have been discarded without suitable application methods. And these SPWWS might causes of marine environmental pollution and waste in potential food resources. (omitted)

• Transactions of Materials Processing
• /
• v.17 no.2
• /
• pp.117-123
• /
• 2008

In this study, optimum processing condition of rolled AZ31 Mg alloy was investigated by utilizing processing map and constitutive equation considering microstructure evolution(dynamic recrystallization) occurring during hot-working. A series of mechanical tests were conducted at various temperatures and strain rates to construct a processing map and to formulate the recrystallization kinetics in terms of grain size. Dynamic recrystallization(DRX) was observed to occur at a domain of $250^{\circ}C$ and 1/s(maximum dissipation-efficiency region). The effect of DRX kinetics on microstructure evolution was implemented in a commercial FEM code followed by remapping of the state variables. The volume fraction and grain size of deformed part were predicted using a modified FEM code and were compared with those of actual hot forged part. A good agreement was observed between the experimented results and predicted ones.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.509-515
• /
• 2015

MAO ceramic coatings were prepared on AZ61 magnesium alloy for various processing times ranging from 5 to 60 min, in an electrolyte solution based on silicate-fluoride. The mechanical, electrochemical and, microstructural properties and the phase compositions of the coating layers were investigated. In this work, unlike previous studies, coatings with high amounts of the $Mag_2SiO_4$ phase were formed which contained small amounts of MgO and $MgF_2$ at a processing condition of 30 min. A microstructural analysis revealed that the porosity of the coatings was reduced considerably with an increase in the processing time, together with a change in the pore geometry from an irregular to a spherical shape. Potentiodynamic polarization and mechanical testing results showed that the coatings acquired after a processing time of 30 min were superior to all of the others.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.5
• /
• pp.817-823
• /
• 2020

In recent, the machining of difficult-to-cut materials such as titanium alloys, stainless steel, Inconel, ceramic, glass, and carbon fiber reinforced plastics (CFRP) used in aerospace, automobile, medical industry is actively researched. Abrasive waterjet is a non-traditional processing method in which ultra-high pressure water and abrasive particles are mixed in a mixing chamber and shoot out jet through a nozzle, and removed by erosion due to collision with a material. In particular, the nozzle of the abrasive waterjet is one of the most important parts that affect the machining quality as with a cutting tool in general machining. It is very important to monitor the condition of the nozzle because the workpiece is uncut or the surface quality deteriorates due to wear, expanding of the bore, damage of the nozzle and clogging of the abrasive, etc. Therefore, in this paper, we propose a monitoring system based on Acoustic Emission(AE) sensor that can detect nozzle condition in real time during AWJ processing.