• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.257-262
• /
• 1997

A compact measurement system is developed to measure in-process errors due to thermal deformation of a machine tool, this system is composed of a gauge, 5gap-sensors and a PC. The gauge is made of invar, which is a material that has a very low thermal expansion coefficient. A new neural network model is constructed to estimate thermally induced machine tool errors based on the measured data,the given data,that is a width of cut,a depth of cut, a feed rate, a spindel speed etc, and the calculated data. The detail of the model proposed is described in the paper together with the experimental methodologies using a proposed compact measurement system to examine the validity of the proposed approach.

• Journal of Powder Materials
• /
• v.1 no.1
• /
• pp.52-59
• /
• 1994

Since the coefficient of thermal expansion (CTE) of matrix phase is larger about 4 times than that of W particle in tungsten heavy alloy, the thermal stresses due to the CTE difference between the two phases are induced in the alloy during heating and cooling processes. In the present study, a series of W heavy alloy containing various W particle volumes of 0 to 90% is made to investigate the residual stress taking place during cooling process. The CTE and residual stress of the series of alloy are measured by dilatometer and X-ray diffractometer. The residual stress of W particle is in compressive stress irrespective of W particle vol% and tends to increase with decreasing W particle vol% while that of the matrix phase is in tensile stress. The measured residual stress of W particle is about a third of calculated thermal stress. The influence of W particle vol% on the residual stress of W heavy alloy is discussed in terms of the deformation behaviors of W particle and matrix phase.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.31-39
• /
• 1995

The surface integrity of a machined surface is an important factor that dictates several performance characteristics of a metal part. In this paper, the surface integrity aspects are presented specifically with respect to the tribological properties of steel. Test specimens were prepared under varying conditions to induce different levels of surface deformation and hardness. Sliding and rolling experiments were performed to assess the friction and wear characteristics of these specimens using a pinon-disk type tribotester and a plate-on-ball type set-up. It is reaffirmed that heat treated steels possess superior sliding and rolling fatigue resistance than raw steel. However, for the case of raw steels machined under varying conditions, the harder specimen resulted in higher wear. This result is attributed to the presence of surface cracks that were induced during machining. The results of such findings will aid in the optimization of surface preparation process for tribological applications of steel.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.4
• /
• pp.253-258
• /
• 2000

The present study aimed to develop the TRIP(transformation induced plasticity) aided high strength low carbon steel sheets using reverse transformation process. The cold-rolled 0.14C-6.5Mn steel was reverse-transformed by slow heating to intercritical temperature region and air cooling to room temperature. An excellant combination of tensile strength and elongation of $98.3kgf/mm^2$ and 44.4% appears. This combination comes from TRIP phenomena of retained austenite during deformation. The stability of retained austenite Is very Important for the good ductility and it depends on diffusion of carbon and manganese during reverse transformation. The air cooling after holding at intercritical temperature retards the formation of pearlite and provides the carbon enrichment in retained austenite, resulting the increase of elongation in cold-roiled TRIP steel.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.58-59
• /
• 2012

Surface hardening mechanism of H13 steel was investigated when ion niriding after shot peening process was applied. Severe plastic deformation induced nanocrystallized grains at surface region. Higher nitrogen concentration was achieved in ion nitrided specimen with shot peening treatment than in single nitrided specimen. The elemental mapping on chromium and nitrogen by TEM-EELs showed chromium dissolved in matrix enhanced bulk nitrogen diffusion at surface region. Higher nitrogen diffusion also caused lattice distortion. Nano-sized grains, higher nitrogen concentration, and lattice diffustion contributed to the surface hardening.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.2
• /
• pp.104-113
• /
• 1998

The line heating method is a popular technique used to form ship hull in shipyards. In order to promote shipbuilding productivity, some researchers have made progress in their studies on automatic fabrication system for plate forming. These researches have, however, focused on heat-induced plate deformation with particular mechanical modelings, and do not yet propose the heating paths applicable to actual plate forming process. In this paper, a new algorithm to determine heating lines is developed to simulate the line heating process. The important feature of this algorithm is that it calculates principal curvatures of deflection difference surface which represents difference between target surface and surface in fabrication. Several trials to typical surface types show its usefulness and good applicability to tactical use.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.146-150
• /
• 1996

A thermal micro actualtor has been fabricated using surface micromachining techniques. It consists of doped ploysilicon as a moving part and TEOS(Tetra Ethyl Ortho Silicate) as a sacrificial layer. The polysilicon was annealed for the reduction of residual stress which is the main cause to its deformation such as bending and buckling. And the newly developed HF VPE(vapor phase etching)process was also used as an effective release method for the elimination of sacrificaial layer. With noliquid involved during any of the steps for relasing, unlike other reported relase techniques, the HF VPE pocess has produced polysilicon microstructures with virtually no process-induced stiction problem. The actuation is incured by the thermal expasion due to current flow in active polysilicon cantilever, which motion is amplified bylever mechanism. The thickness of pllysilicon is 2 .mu. m and the length of active and passive polysilicon cantilever are 500 .mu. m, respectively. The moving distance of polysilicon actuator was experimentally conformed as large as 21 .mu. m at the input voltage level of 10 V and 50Hz square wave. These micro actuator technology can be utilized for the fabrication of MEMS (microlectromechanical system) such as microrelay, which requires large displacement or contact force but relatively slow response.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.1034-1040
• /
• 2003

Tension mask is a part of CRT type devices, which is installed right behind glass-made front panel. Numerous slits on the thin metal sheet enable the electron beams emitted from posterior gun to be focused, resulting in enhanced definition. Flattened and enlarged displays necessitate the imposition of pretension on the masks, in order to improve the robustness of display quality against vibration or impact. High temperature assembly process subsequent to pretensioning, however, degenerates creep resistance of mask material, and common mask may become susceptible to undesirable elongation due to creep. Once tensile stress becomes high enough to induce creep deformation, pretension is substantially loosened. In this study, tension mask assembly is modeled as a combined structure of beams and wire array, and a numerical simulation is attempted for pretensioning followed by high temperature process. Based on a model study, creep occurrence is found to be probable and its adverse influence is quantified. As fur maintaining high tensile force, simply increasing pretension does not seem to be helpful. Instead, the structure of frame needs to be modified somehow, or material for mask needs to be selected properly.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.3
• /
• pp.111-121
• /
• 2007

The paper presents a reliability-based method that can capture the impact of uncertainty of seismic loadings. The proposed method incorporates probabilistic concepts into the classical limit equilibrium and the Newmark-type deformation techniques. The risk of damage is then computed by Monte Carlo simulation. Random process and RMS hazard method are introduced to produce seismic motions and also to use them in the seismic slope analyses. The geotechnical variability and sampling errors are also considered. The results of reliability analyses indicate that in a highly seismically active region, characterization of earthquake hazard is the more critical factor, and characterization of soil properties has a relatively small effect on the computed risk of slope failure and excessive slope deformations. The results can be applicable to both circular and non-circular slip surface failure modes.