• The International Journal of Costume Culture
• /
• v.13 no.1
• /
• pp.62-66
• /
• 2010

Of all the ways that energy is consumed within textile industry, few are as high energy-expending as dyeing process. The energy consumption in dyeing process amounts to 77% of total fuel consumption, 54% of total electricity use. A technical development in terms of efficient saving energy and time as well is required in the process of dyeing textiles. Recently, dyeing experts are investigating new technologies can conserve energy grafting into microwaves, radio waves, infrared lights, etc. Dyeing industry in Korea, however, the research related to energy conservation has been rarely conducted. Accordingly, this study aims to examine the possibility where especially microwaves could be applied to reduce the energy use and enhance dyeing process skill. This study performs the experiment in which microwave is employed as heating condition in dyeing and figures out as color yield being promoted, bathochromic effect would be achieved. Applying microwaves in dyeing process is expected to lower the carbon emission, energy and time wasted, ultimately exalt economic efficiency.

• Transactions of Materials Processing
• /
• v.9 no.4
• /
• pp.413-420
• /
• 2000

In the die casting process, the flow of liquid metal has significant influence on the quality of casting products and die life. For the optimal process design of front housing part of aircon compressor, various analyses were performed in this study by using computer simulation code, MAGMAsoft. The simulation has been focused on the molten metal behaviors during the filling and solidification stages for the sound casting products. Two cases of casting design that have different types of gating system are considered in the analysis. The potential sites where the casting defects may occur is examined by computer simulation and an improved design process is proposed. Also the effect of partial squeeze on the quality of casting products is considered and the optimal time lag after filling process is determined. For the die-stability, the effect of operational parameters such as die temperature, heat cycle and spot cooling on the die life has also been analyzed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.2
• /
• pp.33-38
• /
• 2004

Toner particles used in laser and xerographic printing process is fused on paper surface so strongly that they tend not to detach easily from the recylced paper surface during pulping. Furthermore, the removal efficiency of detached toner particles by conventional screening and flotation process has limitation due to the platy shape and large size of detached toner particles. It has been shown that the removal efficiency of toners in the screening process can be increased by agglomerating the toner particles with fatty alcohol. It is not possible, however, to remove small and platy toner particles by screening process. These small and platy toner particles should be removed by flotation process. In this study the effect of fatty alcohol that used for toner agglomeration on flotation efficiency has been examined. It was shown that flotation efficiency decreased when fatty alcohol was used most probably due to its effect of reducing hydrophobicity of toner particles.

• Journal of the Korean Society of Visualization
• /
• v.13 no.2
• /
• pp.16-21
• /
• 2015

Concentration polarization(CP) phenomena show great potential on desalination technology. As we can control the dimension of silicon based nanochannel system, it can be used to model ion exchange membrane. In this study, to investigate the effect of nanochannel number and working conditions on the CP based desalination process, nanochannel based microfluidic system is fabricated. First, we optimized nanochannel number and working conditions to conduct visualization study on CP based desalination process. Second, we visualized the desalination process with fluorescent dye in the desalination chip. We also visualized that the particles also can be removed by the CP based desalination process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.659-662
• /
• 2002

SL(Stereolithography) part is made by piling up thin layers which causes the stair stepping effect at the surface of SL parts. This effect brings about excessive surface roughness and requires additional post-process finishing such as abrasive techniques that are detrimental to part geometry and time consuming. Hence a wax coating and grinding post-process is proposed to improve the surface quality of SL part. The wax that has suitable properties for the proposed post-process is coated all over the part surface. By grinding the thin layer of coated on the SL part only, the surface roughness can be improved without any damage on the part. From the experimental results, This approach is considered to be very practical fur die casting with RT(Rapid Tooling) techniques.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.66-71
• /
• 2000

The present study tackles the metallurgical subjects involving the thin slab-direct hot rolling process, i.e. mini-mill process. In order to clarify the effect of chemical composition of steel and MnS precipitation behaviors on the development of edge cracking during hot rolling, the content of manganese and sulfur in low carbon steel was varied and the isothermal treatment prior to roughing was applied. Edge cracking during roughing in the hot-rolling process of mini-mill was effectively prevented by means of the isothermal treatment at 115$0^{\circ}C$ for 5 minutes in the 0.4% manganese steel containing sulfur lower than 0.013%. With the increase in manganese content in low carbon steel, coarser MnS developed. The edge cracking index which denotes the total length of edge crack per unit edge-length of rolled specimens was proposed in this paper. It was found that the edge cracking index linearly decreased with the increase in the ratio of MnS.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.31 no.1
• /
• pp.37-53
• /
• 2006

SPI (Software Process Improvement) activities have been considered one of the crucial approaches to achieve high quality, productivity and timely delivery of software products and services. The basic premise of SPI model is that higher maturity levels lead to better performance. In this research, the relationships between SPI results and performance were empirically investigated with Korean software companies. CMM key process areas were categorized into two dimensions, 'Process Implementation' and 'Quantitative Management'. The relationship between process implementation and performance was significant, but the relationship between quantitative management and performance was insignificant. The control variable, size of OU(Organizational Unit), did not have significant impact on the relation ships between SPI activities and OU performance.

• Journal of Korean Academy of Nursing Administration
• /
• v.12 no.2
• /
• pp.287-294
• /
• 2006

Purpose: The purpose of this study was to identify the change of critical thinking disposition and problem solving process in students who experienced problem-based learning. Method: This research design was one group pre-post test design. Twenty-five nursing students who participated in ‘'Nursing Process' course with two PBL packages for a semester in 2004 were the subjects of this study. The data were analyzed by repeated measures of ANOVA, and content analysis. Result: The problem defining in problem solving process was improved significantly, but there was no significant difference in the critical thinking disposition. Conclusion: The results of this study suggest that PBL has a positive effect on nursing students' problem solving process, But for a more significant effect on a continuous base for critical thinking of nursing students, faculties should use web based and simulation-based education for self directed learning along with clinical situation-based scenarios.

• Textile Coloration and Finishing
• /
• v.8 no.5
• /
• pp.1-6
• /
• 1996

To obtain the basic data of the effect of antimicrobic finishing on chrome-tanned leather for apparel, it was studied that the specimens given from each step of manufacturing process, that is, steps before and after neutralization and after fixation were treated with Si-QAC as a antimicrobic finishing agent, and the antimicrobic activity was evaluated. The results were as follows: 1. The bacterial reduction of the specimens finished antimicrobically were 100% and 94.4% before and after neutralization respectively, however, the specimens carried out successive process after antimicrobic finishing exhibited the reduction of 16.5% and 14.8%. It was assumed that the antimicrobic agent was washed off by the successive process. 2. When the antimicrobic finishing was carried out on the specimens after fixation the bacterial reduction was 95.0% and then the specimen carried out successive process was 97.3%. This result indicates that antimicrobic finishing on the leather would be given after fixation rather than before and after neutralization.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.221-224
• /
• 2003

In the open die forging process, it is difficult to optimize process parameters such as die shape, initial ingot size, feeding pitch, rotation angle and other process parameters in the operational environments. Therefore in this study, 3D finite element analysis has been performed to obtain optimal process condition for open die forging process. FEM analyses at various feeding pitches and rotation angles provide process conditions to make round bar having precise dimensional accuracy.