• The Journal of the Korea Contents Association
• /
• v.12 no.12
• /
• pp.126-134
• /
• 2012

The researchers of this study closely looked into the methods for cognitive-scientific approach to problems of marine design at a time when the overall values of marine cultures are acknowledged in full scale. To that end, the researchers analyzed the problems and problem-solving process for the initial approach to marine design. At the same time, the researchers made the matrix of the design-developmental directions by cognitive scientific approach. After selecting the subjects, the researchers collected verbal protocol and behavior protocol which were shown in the process of a designer's thinking. This was for the sake of protocol analysis which is the representative research technique of cognitive science. Based on the collected data, the researchers empirically analyzed the behavior patterns shown in the marine design process so as to develop the design behavior-graph pattern of designers in an objective and systematic way. The behavior graph was helpful for looking into the initial developmental directions of design and for predicting cognitive structure of designers. The researchers hope that this study will become a fundamental material for predicting cognitive directions of designer for planning and designing the marine design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.53-60
• /
• 2003

Large sized marine structures are used under corrosion environment of seawater and applied by severe service loading such as an ocean current, a billow and a tempest. Marine structures are usually constructed by lots of thick wall steel pipes joining welded joints. The thickness of such as steel pipes is usually more than 40mm. The such as steels are called "Thermo-Mechanical Control Process steel (TMCP steel)" strengthened by a heat treatment in process of steel manufactures. The failure, especially crack initiation, of marine structures was starting at weld joints under service condition. Then they should be designed by basis of the fatigue strength under seawater corrosion environment of weld joints. To clarity the fatigue crack initiation behavior is important more than to clarify the crack propagation behavior on the strength design of marine structures, because it is very difficult to find out the crack initiation and propagation phenomena and then even if it will be able to find out, it is considered that the refit of the damaged parts of welded joints have a technical difficulty under the sea. Therefore, it is most important to clarify the corrosion fatigue crack initiation behavior under the seawater condition. But, there is one big difficulty to make a test for thick plate specimen, for example thicker than 40mm. Because, it is need large capacity loading apparatus to test such as thick plate specimen. In this research, the new configuration specimen for fatigue crack initiation tests was proposed. Using this new specimen, it is easy to carry out the fatigue clack initiation tests with relatively low cyclic loading and to observe a fatigue crack initiation behavior.

• Human Ecology Research
• /
• v.54 no.6
• /
• pp.599-610
• /
• 2016

The purposes of this study are to identify the characteristics of limited edition fashion consumers, to analyze their purchase decision-making processes, and to examine negative factors of consumers' recognition toward limited edition fashion products. A qualitative investigation was conducted by doing in-depth interviews with 11 selected consumers in their twenties and thirties who have actively purchased and consumed limited edition fashion products. The results of this study can be summarized as follows. First, there are four sub-categories of appearance management activity, acceptance of fashion trend, information-seeking behavior, and hedonic shopping orientation for the limited edition fashion consumers' characteristics. Second, the purchase decision-making process of limited edition fashion consumers are identified as seven steps: need recognition, information search, evaluation of alternatives, planning and courtship, purchase, post-purchase evaluation, and post-purchase behavior. Courtship/attachment formation and post-purchase behavior are unique steps when compared to general purchase decision-making process. Third, this study identified negative factors of consumers' recognition toward limited edition this study in order to suggest several improvement plans for enterprises using limited marketing. Four sub-categories are examined: outrageous price, tricks of company, fatigue due to purchasing competition, and re-sellers. In conclusion, this study indicates that the purchase decision-making process of limited edition consumers, which involves two distinctive steps including courtship/attachment formation and post-purchase behavior, can be differentiated from general consumers. The results of this study provides preliminary data for further research for in-depth analysis of limited edition consumers.

• The Journal of the Korea Contents Association
• /
• v.20 no.3
• /
• pp.542-559
• /
• 2020

This study was conducted to derive theoretical and practical implications in situations where innovation of the business is desperate in the face of the emergence of agile organizations and digital transformation. To do so, we tried to verify the correlation between negative feedback-seeking behavior and innovative behavior and whether the learning goal orientation of these two variables has a moderated mediating effect by coaching leadership. It analyzed the collected questionnaire from 381 members working in domestic companies; SPSS 25.0, AMOS 25.0, and Process Macro 3.0 were used. The analysis result showed that the negative feedback seeking behavior had a positive effect on the learning goal orientation, and the leader's coaching leadership found to have a moderating effect between the negative feedback seeking behavior and the learning goal orientation. Learning goal orientation has been found to have a moderated mediating effect between negative feedback seeking behavior and innovative behavior. This study is significant in the sense that it reveals the process of how members seeking negative feedback in the organization could be led to innovative behavior and shows the necessity of organizational support for coaching leadership for the vitalization of innovative behavior.

• Transactions of Materials Processing
• /
• v.21 no.6
• /
• pp.341-347
• /
• 2012

The metallic bipolar plates of the molten carbonate fuel cell(MCFC) are composed of shielded slot plates and a center-plate. The shielded slot plates support the center-plate and the membrane electrode assembly. Compressive forces are applied to the shielded slot plate in order to increase the contact area between shielded slot plates and the membrane electrode assembly (MEA). In the design of the shielded slot plate, it is necessary to predict the mechanical behavior of the shielded slot plate. The shielded slot plates are manufactured by a three-stage forming process consisting of slitting, preforming and the final forming process. The mechanical behavior of the shielded slot plate is largely affected by the forming process. In this study, the simulation of the three-stage forming process was used to predict the mechanical behavior of the shielded slot plate. The present simulation approach showed good agreements with the experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.211-219
• /
• 1996

In a small high-speed D. I. diesel engine, the injected fuel spray into the atmosphere of the high temperature is burnt by go through the process of break up, atomization, evaporation and process of ignition. These process are important to decide the emission control and the rate of fuel consumption and out put of power. Especially, in the case of injected fuel spray impinging on the wall of piston cavity, the geometry of piston cavity gives great influence the ignitability of injected fuel and the flame structure. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, the spray was impinged on the wall of 3 types of piston cavity such as Dish, Toroidal, Re-entrant type, in order to analyze the combustion process of impinging spray precisely and systematically. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation σ(t) and variation factor(vf) was measured with the lapse of time.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.467-471
• /
• 2005

In this paper, experimental methods about the flow behavior of thin polymer film by various edge patterns in the spin coating process for stable cover layer coating of a blu-ray disc is described. The blu-ray disc, a next-generation optical disc format over 25GB, consists of a 1.1m thick substrate and a 0.1mm tick cover layer. Generally, cover layer on the blu-ray disc is made by the polymer spin coating process. However, it is hard to secure sufficient coating uniformity around the rim on the cover layer. In order to get the uniform thickness deviation and to minimize the bead around the rim, the edge of the disc substrate can be modified into various patterns, such as normal plain, trench, step and chamfer pattern, etc, around the rim on the disc and experimented with various parameters, such as surface tension, viscosity, coating time, temperature and rotation speed, etc. And the optimal shape of the rim was tried to get by 3 dimensional computer simulation of the polymer expulsion process.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.52-58
• /
• 2009

Generally, a vertical rolling process is used to achieve extensive width reduction in hot strip mill. However, it is impossible to avoid the defects such as dog-bone and edge-seam defect. The sizing press process has been developed in response to the defects mentioned above. Especially, this study is carried out to investigate the deformation of slab by two-step sizing press. The deformation behavior of slab in the sizing press process is more favorable than that in conventional vertical rolling edger. The FE-simulation is applied to predict the deformation behavior of the slab. In this paper, the several causes of the asymmetrical deformation are mentioned for the purpose of understanding of the anvil shape. Load, dog-bone and edge-seam defect are discussed in width sizing process considering the anvil shape. And to reduce the problems generated at rougher mill just after sizing press, these are studied in this paper. The deformation behavior of slabs and optimum anvil shape are obtained by rigid-plastic finite element analyses and neural network.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.114-117
• /
• 2009

In this work, closing behavior of the voids generated in a casting process was investigated for various parameters such as reductions in height void size and billet rotation during hot open die forging process. The reduction in height and path schedule including the number of paths and billet rotation were chosen as key process variables to express the change of geometrical void shape and void closing behavior. On the other hand, values of die overlapping and die width ratio were set to be constant. Extend of void closure was observed and evaluated using tensile test and microscope. Based on the experimental result, it is ensured that void closure do not occur at 15% and 30% reduction in height as well as one or two rotations of a billet. The useful datum obtained from this study could be utilized to establish an optimum path schedule in the open die forging process.

• Journal of Digital Convergence
• /
• v.12 no.11
• /
• pp.225-232
• /
• 2014

Supply of a smart device has been made with the development of communication networks and growing desire of people to improve the quality of life, the service industry about it have been made with smart devices. Among them, there are various services that can help people change their behavior to healthy life. But it does not have a large impact on the behavior change of performer because its been developed as a general process. Therefore in this study examine development situation about current behavior change applications through application markets. Development current situation can be separated by process to two patterns. As a result we propose behavioral change model that includes integrated change model that one of the behavior theory model, accomplish the goal process of goal setting theory and habit formation phase for automate the changes. Also, we provide appropriate service according to the model that leads motivation, sustainability of the action and positive behavior change to performer. We can expect in many aspects such as ability and motivation than existing service.