• Journal of Mechanical Science and Technology
• /
• v.17 no.6
• /
• pp.879-887
• /
• 2003

The flow in a parallel walled test channel, when obstructed with a geometry at the entrance, can be forward, reverse and stagnant depending on the position of the obstruction. This interesting flow phenomenon has potential benefit in the control of energy and various flows in the process industry In this experiment, the flat plate obstruction geometry was used as an obstruction at the entry of the test channel. The parameters that influence the flow inside and around the test channel were the gap (g) between the test channel and the obstruction geometry, the length (L) of the test channel and the Reynolds number (Re). The effect of the gap to channel width ratio (g/w) on the magnitude of the velocity ratio (V$\_$i/ / V$\_$o/ : velocity inside/ velocity outside the test channel) was investigated for a range of Reynolds numbers. The maximum reverse flow observed was nearly 20% to 60% of the outside velocity for Reynolds number ranging from 1000 to 9000 at g/w ratio of 1.5. The maximum forward velocity inside the test channel was found 80% of the outside velocity at higher g/w ratio of 8. The effect of the test channel length on the velocity ratio was investigated for different g/w ratios and a fixed Reynolds number of 4000. The influence of the Reynolds number on the velocity ratio is also discussed and presented for different gap to width ratio (g/w). The flow visualisation photographs showing fluid motion inside and around the test channel are also presented and discussed.

• Journal of Sensor Science and Technology
• /
• v.26 no.2
• /
• pp.96-100
• /
• 2017

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been extensively studied as the active material in ammonia gas sensor because of its fast response time, high conductivity and environmental stability. It is well known that a post annealing process for organic devices based on PEDOT:PSS significantly increases the device performance. In this study, we propose the solvent annealing of PEDOT:PSS and investigated its effects. As a results, post solvent annealing on PEDOT:PSS lead to the surface chemical and physical properties change. These changes result in improved conductivity of the PEDOT:PSS. In additional, ammonia sensitivity of solvent annealed PEDOT:PSS become higher than pristine polymer film. The enhancement is mainly caused by the depletion of gas barrier PSS and structural re-forming PEDOT networks. We believe that the post solvent annealing is a promising method to achieve highly sensitivity PEDOT:PSS films for applications in efficient, low-cost and flexible ammonia gas sensor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.115-123
• /
• 2010

Cool-down performance after soaking is important because it affects passenger's thermal comfort. The cooling capacity of HVAC system determines initial cool down performance in most cases, the performance is also affected by location, and shape of panel vent, indoor seat arrangement. Therefore, optimal indoor designs are required in developing a new car. In this paper, initial cool down performance is predicted by CFD(computational fluid dynamics) analysis. Experimental time-averaging temperature data are used as inlet boundary condition. For more reliable analysis, real vehicle model and human FE model are used in grid generation procedure. Thermal and aerodynamic characteristics on re-circulation cool vent mode are investigated using CFX 12.0. Thermal comfort represented by PMV(predicted mean vote) is evaluated using acquired numerical data. Temperature and velocity fields show that flow in passenger's compartment after soaking is considerably unstable at the view point of thermodynamics. Volume-averaged temperature is decreased exponentially during overall cool down process. However, temperature monitored at different 16 spots in CFX-Solver shows local variation in head, chest, knee, foot. The cooling speed at the head and chest nearby panel vent are relatively faster than at the knee and foot. Horizontal temperature contour shows asymmetric distribution because of the location of exhaust vent. By evaluating the passenger's thermal comfort, slowest cooling region is found at the driver's seat.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.229-234
• /
• 2005

Following the recent trend in the automotive manufacturing technologies, the product design subject to the die casting becomes more and more complex. The requirement of the die design becomes more demanding than ever before. In some cases the product's shape can have multiple slender manifolds. In such cases, design of the inlet and outlet parts of the die is very important in the whole manufacturing process. The main issues required for the qualified products are to attain gentle and uniform flow of the molten liquid within the passages of the die. To satisfy such issues, the inlet cylinder ('bed cylinder' in this paper) must be as large as possible and simultaneously the outlet opening at the end of each passage must be as small as possible. However these in turn obviously bring additional manufacturing costs caused by re-melting of the bed cylinder and increased power due to the small outlet-openings. The purpose of this paper is to develop effective simulation methods of calculation for fluid flows in multiple columns, which mimic the actual complex design, and to get some useful information which can give some contributions to the die-casting industry. We have used a commercial code CFX in the numerical simulation. The primary parameter involved is the size of the air-vent. We will show how the very small opening of the outlet, i.e. the air-vent, can be treated with the aid of the porous model provided in the code. To check the validity of the numerical results we have also conducted a simple experiment by using water.

• Journal of the Korean Society of Safety
• /
• v.23 no.4
• /
• pp.13-18
• /
• 2008

This study deals with finish roll forming by forced displacement can be conceived as a method of eliminating errors in conventional form rolling under constant loads. This method produces a high-precision tooth profile by low-speed form rolling when a high rigid screw or cam is used at the pressurized section. Tooth profile is decided in the beginning of roll forming and ${\delta}_{max}$ mainly increases if the number of roll forming process is increased. Gear class is improved by one or two class after roll forming if the gear has convex type error and pressure angle error in KS 4 class. If the gear have concave type error and pressure angle error and pressure angle error, gear class is not improved in theory, but improved a little in practice. In the finishing roll forming, it inevitably yields both the concaving of tooth profile and plastic deflection of addendum of teeth. Experiments show that the concaving and the plastic deflection are successfully reduced, the accuracy of tooth profile reaches to KS 0 class.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.423-428
• /
• 2005

Due to the fast growing rate of the global container trade, every major port is under the pressure of meeting the projected capacity demand. As a result, alternative solutions have been sought for improving capacity and meeting the growing demand for container storage area and terminal capacity. Moreover, material handling process re-engineering is now a critical issue for logistics and supply chain managers of airline, shipping lines, terminal and warehousing enterprises around the world. Therefore, the purpose of this paper is to develop the 3D simulator for executing performance valuation of port transportation systems. The developed 3D simulator system is to measure the effectiveness of the proposed total system and compare it with existing practices. The performance analysis variables are also defined for these comparisons.

• Journal of Broadcast Engineering
• /
• v.21 no.4
• /
• pp.578-591
• /
• 2016

In this paper, the fast encoding algorithm in High Efficiency Video Coding (HEVC) encoder was studied. For the encoding efficiency, the current HEVC reference software is divided the input image into Coding Tree Unit (CTU). then, it should be re-divided into CU up to maximum depth in form of quad-tree for RDO (Rate-Distortion Optimization) in encoding precess. But, it is one of the reason why complexity is high in the encoding precess. In this paper, to reduce the high complexity in the encoding process, it proposed the method by determining the maximum depth of the CU using a hierarchical clustering at the pre-processing. The hierarchical clustering results represented an average combination of motion vectors (MV) on neighboring blocks. Experimental results showed that the proposed method could achieve an average of 16% time saving with minimal BD-rate loss at 1080p video resolution. When combined the previous fast algorithm, the proposed method could achieve an average 45.13% time saving with 1.84% BD-rate loss.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.9
• /
• pp.1165-1171
• /
• 2018

CNN requires a large amount of computation and memory in the process of extracting the feature of the object. Also, It is trained from the network that the user has configured, and because the structure of the network is fixed, it can not be modified during training and it is also difficult to use it in a mobile device with low computing power. To solve these problems, we apply a pruning method to the pre-trained weight file to reduce computation and memory requirements. This method consists of three steps. First, all the weights of the pre-trained network file are retrieved for each layer. Second, take an absolute value for the weight of each layer and obtain the average. After setting the average to a threshold, remove the weight below the threshold. Finally, the network file applied the pruning method is re-trained. We experimented with LeNet-5 and AlexNet, achieved 31x on LeNet-5 and 12x on AlexNet.

• Journal of Broadcast Engineering
• /
• v.26 no.5
• /
• pp.533-542
• /
• 2021

In this study, a process of re-creating Jindo Buk Chum, one of the traditional Korean arts, into digital art using various artificial intelligence technologies was proposed. The audience's emotional data, quantified through artificial intelligence language analysis technology, intervenes in various object forms in the projection mapping performance and affects the big story without changing it. If most interactive arts express communication between the performer and the video, this performance becomes a new type of responsive performance that allows the audience to directly communicate with the work, centering on artificial intelligence emotion analysis technology. This starts with 'Chuimsae', a performance that is common only in Korean traditional art, where the audience directly or indirectly intervenes and influences the performance. Based on the emotional information contained in the performer's 'prologue', it is combined with the audience's emotional information and converted into the form of images and particles used in the performance to indirectly participate and change the performance.

• Journal of Animal Reproduction and Biotechnology
• /
• v.37 no.4
• /
• pp.231-238
• /
• 2022

Reactive oxygen species (ROS) production and F-actin cytoskeleton dynamics play important roles in the survival rate of blastocysts after the vitrified-warming process. However, the protective effects of Mito-TEMPO against cryo-injury and viability through F-actin aggregation and mitochondrial-specific ROS production in vitrificated-warmed bovine embryos have not been investigated. The aims of the present study were to: (1) determine the effects of Mito-TEMPO on embryonic developmental competence and quality by F-actin stabilization during in vitro culturing (IVC), and (2) confirm the effects of Mito-TEMPO through F-actin structure on the cryotolerance of vitrification-warming in Mito-TEMPO exposed in vitro production (IVP) of bovine blastocysts. Bovine zygotes were cultured with 0.1 μM Mito-TEMPO treatment for 2 days of IVC. Mito-TEMPO (0.1 μM) exposed bovine embryos slightly improved in blastocyst developmental rates compared to the non-treated group. Moreover, the viability of vitrified-warmed blastocysts from Mito-TEMPO treated embryos significantly increased (p < 0.05, non-treated group: 66.7 ± 3.2% vs Mito-TEMPO treated group: 79.2 ± 5.9%; re-expanded at 24 hours). Mito-TEMPO exposed embryos strengthened the F-actin structure and arrangement in the blastocyst after vitrification-warming. Furthermore, the addition of Mito-TEMPO into the IVC medium enhanced embryonic survival and quality through F-actin stabilization after the vitrification-warming procedure. Overall, our results suggest that supplementing the culture with 0.1 μM Mito-TEMPO improves the embryonic quality and cryo-survival of IVP bovine blastocysts.