• The Research Journal of the Costume Culture
• /
• v.28 no.5
• /
• pp.607-620
• /
• 2020

The aim of this study is to define the new expressive techniques for multicolored clamp resist (hyuphill) dyeing, based on empirical verification on relics that are estimated to be dyed by the exchange of more than two wood blocks: a previously undiscovered technique. Clamp resist dyeing (assumed to be made by exchanging wood blocks) have uneven resist printing lines or cloudy gradation. These are reproduced as follows: first, they have uneven contour lines, particularly with the color blue. It is possible to exchange wood blocks separately on patterns with uneven resist printing lines, and it has been verified that the exchange of wood blocks makes these irregular resist printing lines. It has also been verified that exchanging the wood blocks according to the gradation (to emphasize the cubic effect on the patterns) yields clamp resist dyeing with no resist printing lines but with cloudy gradations that have accented borders. This study provides basic information that enables methods of multicolored clamp resist dyeing through wood block exchange to be deduced (something that has not been attempted for a long time). Thus, the revival of the modern Korean dyeing culture based on the conservation and perseverance of the traditional dyeing techniques can be achieved.

• ETRI Journal
• /
• v.42 no.2
• /
• pp.272-281
• /
• 2020

Three-dimensional (3D) selfie services, one of the major 3D printing services, print 3D models of an individual's face via scanning. However, most of these services require expensive full-color supporting 3D printers. The high cost of such printers poses a challenge in launching a variety of 3D printing application services. This paper presents a stencil-based 3D facial relief creation method employing a low-cost RGBD sensor and a 3D printer. Stencil-based 3D facial relief is an artwork in which some parts are holes, similar to that in a stencil, and other parts stand out, as in a relief. The proposed method creates a new type of relief by combining the existing stencil techniques and relief techniques. As a result, the 3D printed product resembles a two-colored object rather than a one-colored object even when a monochrome 3D printer is used. Unlike existing personalization-based 3D printing services, the proposed method enables the printing and delivery of products to customers in a short period of time. Experimental results reveal that, compared to existing 3D selfie products printed by monochrome 3D printers, our products have a higher degree of similarity and are more profitable.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.593-597
• /
• 2015

Ni ink for electrohydrodynamic (EHD) continuous jet printing has been developed by using Ni nanoparticles mixed with conhesiveness provider. EHD continuous jet printing was used in order to realize $20{\mu}m$ pattern width. Ink stability was investigated by using Turbi-scan which monitors agglomeration and precipitation of nanoparticles in the ink for three days. The Turbi-scan results showed that the formulated Ni ink had been stable for 3 days without any indication of precipitation across the entire ink. Antireflection coating (ARC) layer in crystalline solar cell wafers was removed by laser ablation technique leading to the formation of 84 grooves where the Ni ink was printed by EHD continuous jet printing. The printability and microstructure of EHD-jet-printed Ni lines were investigated by using optical and electron microscopes. 84 Ni lines with the width less than $20{\mu}m$ were successfully printed by one-time printing without any misalignment and fill the laser-ablated ARC grooves.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.259-262
• /
• 2009

Several universities in Korea are beginning studies related to soft stamping processes but since the studies are done with manual works thus systematic tests can't be performed due to difficulties in producing reproducible and repeatable fine patterns. Therefore, the phenomenon of destruction of the pattern forms of elastic polymers occurred during working because of inconsistent printing pressures and pinting time and there have been difficulties in maintaining flatness or producing uniform and fault-free fine structures in pinting large areas and also, there have been difficulties in multi-layered processes as patterns were changed by contacts in registering and errors in alignments. The purpose of development of this technology is to improve the process of soft lithography so that contacts between PDMS stamps and metal coated substrates in order to develop a stamp printing device that can not only shorten but also optimize processes, secure reproducibility and repeatability and is advantageous in printing large areas. Also, using this technology, this author is to develop equipment technologies and applied technologies for nano grade pattern printing processes with new concepts based on fine contact printing processes in order to apply them to diverse nano pattering processes.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.3
• /
• pp.174-181
• /
• 2018

This paper examines the structural behavior of 3D printed concrete specimens with focus on the bond between the layers. The tensile bond and flexural strengths were investigated experimentally and compared with those of specimens made by conventional mold casting. The test parameters were the time gap between printing layers and the reinforcement between vertical layers. The results showed the 3D printed specimens had voids between layers and confirmed the strength reduction due to printing time gap and the stress concentration caused by the voids. Most of the reduction in tensile bond strength between layers was due to the stress concentration at least up to certain printing time gap. Moreover, beyond a certain printing time gap (24hours), the additional reduction in tensile bond strength reached a level that could affect the structural behavior. The reinforcement between layers was helpful to increase the ductile behavior which is essential to prevent the sudden collapse of the structure. In addition, the reduction in flexural strength due to the stress concentration by the voids was observed and should be considered in the design of 3D printed wall structures against the lateral load.

• Fibers and Polymers
• /
• v.5 no.2
• /
• pp.117-121
• /
• 2004

Optimum condition concerning the content of pretreatment print paste and steaming time for ink-jet printing was newly developed through the orthogonal analysis. The cotton fabric treated under the newly developed optimum condition could achieve a high level of colour yield similar to that of the commercially pretreated cotton fabric available in the market for ink-jet printing. The results were discussed thoroughly in this paper.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2160-2163
• /
• 2005

Solid freeform fabrication (SFF) technology plays a major role in industry and represents a reasonable percentage of industrial rapid prototyping/tooling/manufacturing (RP/RT/RM) development applications. However, SFF technology still has long way to progress to achieve satisfactory process speed, surface finish and overall quality improvement of its application. Today, three dimensional printing (3DP) technique that is one of SFF technology is receiving many interests, and is applied by various fields. It can fabricate three dimensional objects of solid freeform with high speed and low cost using ink jet printing technology. However, need long curing time after manufacture completion. And it must do post-processing process necessarily to heighten strength of objects because strength of fabricated objects is very weak. Therefore, in this study, we proposed an improved 3DP process that can solve problems of conventional 3DP process. The general 3DP process is method to spout binder simply through printer head on powder, but proposed process is method to cure jetted UV resin by UV lamp after jet UV resin using printhead on powder. The hardening of resin is achieved strongly at early time by UV lamp in proposed method. So, the proposed process can fabricate three dimensional objects with high speed without any post-processing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.839-844
• /
• 2017

In the past few years, three-dimensional (3D) printing has been developed as a rapid prototyping (RP) technique. The fused deposition modeling (FDM)-type 3D printing is one of the most useful RP methods; however, it still has several disadvantages, such as low conductivity, heat degradation, and low surface quality. In this study, test specimens are fabricated using an FDM-type 3D printer with an ABS material. Then, the specimens undergo post-processing on submerging in acetone with various processing times. As the processing time increases, surface roughness is enhanced significantly within the first five seconds by chemical processing, following which the processing effects are reduced. Furthermore, post processing causes the ultimate strength and strain to increase slightly with increased processing time.

• Textile Coloration and Finishing
• /
• v.20 no.1
• /
• pp.48-56
• /
• 2008

A real-time inspection system has been developed by combining CCD based image processing algorithm and a standard lighting equipment. The system was tested for defective fabrics showing nozzle contact scratch marks, which are one of the frequently occurring defects. Two algorithms used were compared according to both their processing time and detection rate. First algorithm (algorithm A) was based on morphological image processing such as dilation and opening for effective treatment of defective printing areas while second one (algorithm B) mainly employs well-defined edge detection technique based on canny detector and Zermike moment. It was concluded' that although both algorithms were quite successful, algorithm B showed relatively consistent performance than algorithm A in detecting complex patterns.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2004

The key points of the CTP board is as follows: Film, brightness, plate exposure is eliminated, the reduction of personal expenses, and the reduction of time consumption. But above all, the accurate reappearance of the highlighting and shadow portion as well as self modification of the dust edge portion stands out as the most impressive improvements. In this paper, using a digital test from 4.0 and a Thermal CTP color printing control, the two parts of the Thermal CTP utilized a 1%-99% dot reappearance. Also, using an opposite line target, the results of the CTP plates and printing were compared. Finally, research was made on the printing quality on the slur development of the plate and the result when there was a lack of weave connection.