• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.342-345
• /
• 2002

As the size of chip components and module decreases, new patteming method for fine line and geometry is needed. So far, in LTCC(Low Temperature Cofired Ceramic) process, screen printing method has been used generally. But screen printing method has some disadvantages as follows. First, the geometry including line, vias, etc. smaller than $100{\mu}m$ can't be evaluated easily. Second, the patterned dimension is different from designed value, which makes distortion in charactersitics of not only chip components but also modules. Thick film lithography has advantages of thick film screen printing process, low cost and thin film process, fine line feasibility. Using this method, the line with $30{\mu}m$ width and the geometry with expected dimension can be evaluated. In this study, the fine line with $35{\mu}m$ line/space is formed and the embedded capacitor with very small tolerance is developed using thick film lithography.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.1
• /
• pp.15-22
• /
• 2008

For the improvement of letterpress printing paper quality, special fibers obtained from the sea were used by mixing with wood fibers. The sizes of the special fibers, which were from red algae in the sea, were 0.5-1 mm in length, and 3-7 ${\mu}m$ in width, respectively, and the fibers were supplied by Pegasus Research Inc. for the study. From the study, it was found that 10% addition of algae fibers greatly improved paper surface strength and internal bonding strength. The compressibility was estimated by utilizing 'Print-surf method' at high clamping pressure and with hard backing. Again, 10% addition of algae fibers greatly improved the compressibility of the paper. These results were expected that algae and wood fibers were distributed evenly through the sheet, and integrated one another to leave no empty space inside the paper.

• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.8-15
• /
• 2024

This thesis investigates the jetting characteristics of an aerosol jet printing (AJP) process as a function of design and operating conditions. The governing equations of the AJP system are derived for experimentation and analysis. To understand the characteristics of the AJP system, it analyzes the jetting characteristics as a function of the flow rate of the carrier gas and the sheath gas, and the variation of the linewidth with the nozzle exit size based on particle tracking. The thesis focuses on computational fluid dynamics (CFD), which is a computer simulation. The particle tracking results obtained by CFD were analyzed using MATLAB. CFD analytical models can be analyzed in environments with different conditions and consider more specific situations than mathematical computational models. The validity of the CFD analysis is shown by comparing the experimental results with the CFD analysis.

• Journal of Drive and Control
• /
• v.21 no.2
• /
• pp.8-14
• /
• 2024

This paper investigates the jetting characteristics of an aerosol jet printing (AJP) process as a function of design and operating conditions. The governing equations of the AJP system are derived for experimentation and analysis. To understand the characteristics of the AJP system, this thesis analyzes the jetting characteristics as a function of the flow rate of the carrier gas and the sheath gas, and the variation of the linewidth with the nozzle exit size based on particle tracking. This thesis focuses on computational fluid dynamics (CFD), which is a computer simulation. The particle tracking results obtained by CFD were analyzed using MATLAB. CFD analytical models can be analyzed in environments with different conditions and consider more specific situations than mathematical computational models. The validity of the CFD analysis is shown by comparing the experimental results with the CFD analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.669-670
• /
• 2011

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.573-577
• /
• 2013

The one of the most important issue in roll-to-roll gravure printing is increase of ink transfer ratio or printability. As the result of high ink transfer ratio or printability, we can assess the quality of the printed patterns. The rheological properties are the important factors for the printability of electrodes patterning. In this study, the rheological properties of conductive ink are controlled by adding the solvent. The inks with different rheological properties are used for the patterning of the electrodes of $100{\mu}m$ by gravure printing equipment. The various printing speed, which also affect the rheological properties of conductive ink, is applied and the printed patterns are compared for their width and aspect ratio. Decreasing in the ink viscosity as well as increasing in the printing speed decreases the printability in gravure patterning, which shows that the rheological properties are important factors for the printability of gravure patterning.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.7-14
• /
• 2010

This paper describes the effects of kinetic parameters such as attaching speed, attaching time, and dettaching speed on printing property of electrodes which were fabricated by micro-contact printing with Ag ink. In inking process the attaching speed was preferable to be less than 1 mm/s, attaching time as short as possible, and detaching speed larger than 1000 mm/s in order to obtain the transfer ratio of ink larger than 98%. Meanwhile in printing process the parameters were totally opposite to the results of inking process; attaching speed larger than 100 mm/s, attaching time larger than 30 sec, and detaching speed less than 1 mm/s for the best results. With the parameters we could obtain the micro-contact printed electrodes with the minimum line width of $30\;{\mu}m$, thickness of 300~500 nm, roughness less than 50 nm, and resistivity of about $15{\sim}16{\mu\Omega\cdot}cm$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.506-508
• /
• 2005

In general, organic TFTs are comprised of four components: gate electrode, gate dielectric, organic active semiconductor layer, and source and drain contacts. The TFT current, in turn, is typically determined by channel length and width, carrier field effect mobility, gate dielectric thickness and permittivity, contact resistance, and biasing conditions. More recently, a number of techniques and processes have been introduced to the fabrication of OTFT circuits and displays that aim specifically at reduced fabrication cost. These include microcontact printing for the patterning of metals and dielectrics, the use of photochemically patterned insulating and conducting films, and inkjet printing for the selective deposition of contacts and interconnect pattern. In the fabrication of organic TFTs, microcontact printing has been used to pattern gate electrodes, gate dielectrics, and source and drain contacts with sufficient yield to allow the fabrication of transistors. We were fabricated a pentacene OTFTs on flexible PEN film. Au/Cr was used for the gate electrode, parylene-c was deposited as the gate dielectric, and Au/Cr was chosen for the source and drain contacts; were all deposited by ion-beam sputtering and patterned by microcontact printing and lift-off process. Prior to the deposition of the organic active layer, the gate dielectric surface was treated with octadecyltrichlorosilane(OTS) from the vapor phase. To complete the device, pentacene was deposited by thermal evaporation and patterned using a parylene-c layer. The device was shown that the carrier field effect mobility, the threshold voltage, the subthreshold slope, and the on/off current ratio were improved.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.910-912
• /
• 2006

Barrier ribs in plasma display panels (PDPs) function to maintain the discharge space between the glass plates as well as to prevent optical cross-talking. The barrier ribs currently employed are typically $300{\mu}m$ pitch, $110{\sim}120{\mu}m$ in height, with upper and lower widths of $50{\mu}m$ and $80{\mu}m$, respectively. It has been reported that barrier ribs can be fabricated by screen-printing, sand blasting, etching and photolithographic processes. In this study, photosensitive barrier rib pastes were formulated and systematically evaluated in terms of photolithographic process variables such as printing, drying, UV exposure, development and sintering. It was found that the use of UV absorbent, polymerization inhibitor and surfactant were very effective in controlling the width uniformity of barrier ribs in the photolithographic method of barrier rib patterning.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.28 no.1
• /
• pp.15-24
• /
• 2010

Photovoltaic solar cells are all in the incident because they are not converted into electrical energy, high-efficiency solar cells in order to reduce the loss of elements must be. Significant factor in the loss of solar cells, optical loss and electrical loss can be divided into. Optical losses occur when the sun will be joined on the surface of the reflection, the shadow loss due to electrodes, and the losses are in the solar wavelengths. Commercialization is currently the most common solar cells on the front of the light incident on the electrode is formed. Therefore, the shadow caused by the electrode to cover the dead area of the sun, due to factors that hinder the absorption of sunlight which is shadowing them and conversion efficiency of solar cells is the inhibition factor. These barriers to eliminate the electrode linewidth reduces the shadowing to reduce, but simply of the electrode line width is reduced electrode area by reducing the series resistance elevates this because to improve the electrode Aspect ratio(height/width) to increase Ag development of paste is required. In this study, aspect ratio of screen-printing method to increase the electrode Ag paste composition of the binder for the characterization of rheology in the shadow of the electrode by reducing the optical loss of the photoelectric conversion efficiency of solar cells to boost the performance measures was. Properties and printability of the paste, the binder resin sintered characteristics that affect the thermal properties are excellent with a good screen printability acrylic resin, ethyl cellulose, using a resin were evaluated. Prepared paste rheology properties, was formed to evaluate the electrode conductivity and aspect ratio.