• Journal of Yeungnam Medical Science
• /
• v.40 no.3
• /
• pp.302-307
• /
• 2023

With recent developments in digital dentistry, research on techniques and materials for three-dimensional (3D) printing is actively underway. We report the clinical applications and outcomes of 3D printing of temporary crowns fabricated with polylactic acid (PLA) using a fused deposition modeling (FDM) printer. Five participants were recruited from among patients scheduled to be treated with a single full-coverage crown at a dental clinic in a university medical center from June to August 2022. We used 3D-printed crowns fabricated with PLA using an FDM printer as temporary crowns and were assessed for discomfort, fracture, and dislodging. The 3D-printed temporary crowns were maintained without fracture, dislodging, or discomfort until the permanent prosthesis was ready. The average time required for printing the temporary crowns was approximately 7 minutes. The 3D printing of temporary crowns with PLA using an FDM printer is a convenient process for dentists. However, these crowns have some limitations, such as rough surface texture and translucency; therefore, the 3D printing process should be improved to produce better prostheses.

• The Journal of Korean Academy of Prosthodontics
• /
• v.60 no.3
• /
• pp.246-253
• /
• 2022

Flabby tissue is not rare for denture wearers. Mucostatic impression technique is necessary due to compromised retention and stability of denture resulting from distortion of mobile flabby tissue. In this report, individual tray was fabricated by model-scanning and 3D printing treatment denture. And then, mucostatic impression for flabby tissue was obtained by using individual tray modified with window technique. Definitive denture was fabricated based on information of treatment denture including incisal pontic arrangement, jaw relationship and occlusion.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.16 no.4
• /
• pp.229-235
• /
• 2014

This study conducted a research on burn-out printing convergence technology for cellulose blend knit fabrics. Printing technology, which forms color pattern on the fabric, can be generally classified into four according to printer or printing method, e.g. screen printing, roller printing, rotary printing, digital printing. However, these printing methods are flat in design or pattern, which have limitation to overcome monotonousness of fabric, so that recently burn-out process method, which expresses three-dimensional pattern effect by treating chemical on the surface of fabric as the method to appeal its esthetics to the customers. Particularly, in case of cellulose/polyester composite material, first, it is proceeded in 2 processes, by dyeing cellulose or polyester fabric and burning out cellulose fabric, in this process, due to pollution caused by disperse dye migration, color of polyester fabric part could be discolored, which has high falt risk. This research considered coloring burn-out technique, which simultaneously proceed dyeing and burn-out by reducing dyeing and burn-out process to 1 stage, which were proceeded in 2 stages previously. As the research result, it was confirmed that reasonable depth of roller was 0.04~0.06mm in roller printing process, heat treatment condition of burn-out far-infrared radiation was $185^{\circ}C{\times}30m/min$. Color fastness to washing was confirmed to be 4-5 grade, color fastness to rubbing, 3-4 grade, color fastness to light, 4 grade. Also, it was confirmed that energy reduction effect appeared 38.19%, in case of energy cost per yard compared to the existing production, also, 19.74%, in case of production cost.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.108-108
• /
• 2017

In this study, biocomposite filaments with agricultural by-products can be used in extrusion-based 3D (Three-dimensional) printing. Extrusion-based 3D printing stands as a promising technique owing to its versatility. We hypothesized that bio-filament composite consisted of something derived from agricultural by-products could be used as 3D printing materials that could overcome the drawbacks of PCL (poly-caprolactone). Bio-filament mixed with PCL and agricultural by-products was defined as r-PCL in this study. In order to find it out the optimal mixing ratio of filaments, we had investigated PCL, r-PCL 10%, r-PCL 20%, r-PCL 50% separately. The morphological and chemical characteristics of the filaments were analyzed by FE-SEM (Field emission scanning electron microscope) and EDX (Energy-dispersive X-Ray spectroscopy), and the mechanical properties were evaluated by stress-strain curve, water contact angle, and cytotoxicity analysis. Results of this study have been shown as a promising way to produce eco-friendly bio-filaments composite for FDM (Fused deposition modeling) method based 3D printing technology. Thus, we could establish biomimetic scaffolds based on bio-printer filaments mixed with agricultural by-product.

• Transactions of the KSME C: Technology and Education
• /
• v.1 no.2
• /
• pp.187-192
• /
• 2013

Nozzle printing technology has been usually used for adhesive patterning to encapsulate electronic devices. Film formation of functional materials by nozzle printing is a great challenge. The characteristics of nozzle printing of organic ink were investigated systematically in this paper. TAPC as an organic emitting material was used as an ink for nozzle printing experiment to form the patterns in this study. Printed pattern width was increased as the ink flow rate and the printed substrate temperature were increased. The patterns showed a coffee-ring shape.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.1-10
• /
• 2014

Offset paper printing is a promising roll-to-roll technique for color printed materials. Although it is no doubt that understanding ink transfer mechanism in offset printing process is necessary to achieve high printing quality, investing the relationship between inks and substrates at the nip is difficult experimentally due to high printing speed. In this paper, rheological behavior and splitting point of the ink at the nip is studied using package software Ployflow and Flow 3D based on Navier-Stokes equation. Polydimethylsiloxane (PDMS) ink and IGT printability tester were used for an model ink and experiment to compare with that of simulation data, respectively. As a result, higher viscosity at state flow and pressure increased ink transfer due to higher possibility of presence of cavitation at the nip and increase in covering area ratio. These results have shown good agreements with experimental data compared by measuring density of print through.

• The Research Journal of the Costume Culture
• /
• v.28 no.5
• /
• pp.607-620
• /
• 2020

The aim of this study is to define the new expressive techniques for multicolored clamp resist (hyuphill) dyeing, based on empirical verification on relics that are estimated to be dyed by the exchange of more than two wood blocks: a previously undiscovered technique. Clamp resist dyeing (assumed to be made by exchanging wood blocks) have uneven resist printing lines or cloudy gradation. These are reproduced as follows: first, they have uneven contour lines, particularly with the color blue. It is possible to exchange wood blocks separately on patterns with uneven resist printing lines, and it has been verified that the exchange of wood blocks makes these irregular resist printing lines. It has also been verified that exchanging the wood blocks according to the gradation (to emphasize the cubic effect on the patterns) yields clamp resist dyeing with no resist printing lines but with cloudy gradations that have accented borders. This study provides basic information that enables methods of multicolored clamp resist dyeing through wood block exchange to be deduced (something that has not been attempted for a long time). Thus, the revival of the modern Korean dyeing culture based on the conservation and perseverance of the traditional dyeing techniques can be achieved.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1511-1514
• /
• 2009

Organic light emitting layer in OLED device was formed by gravure printing process in this work. Organic surface coated by gravure printing typically showed relatively bad uniformity. Thickness and roughness control was characterized by applying various mixed solvents in this work. Poly (N-vinyl carbazole) (PVK) and fact-tris(2-phenylpyridine)iridium($Ir(ppy)_3$) are host dopant system materials. PVK was used as a host and Ir(ppy)3 as green-emitting dopant. To luminance efficiency of the plasma treatment on etched ITO glass and then PEDOT:PSS spin coated. The device layer structure of OLED devices is as follow Glass/ITO/PEDOT:PSS/PVK+Ir(ppy)3-Active layer /LiF/Al. It was printed by gravure printing technology for polymer light emitting diode (PLED). To control the thickness multi-printing technique was applied. As the number of the printing was increased the thickness enhancement was increased. To control the roughness of organic layer film, thermal annealing process was applied. The annealing temperature was varied from room temperature, $40^{\circ}C$, $80^{\circ}C$, to $120^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.593-597
• /
• 2015

Ni ink for electrohydrodynamic (EHD) continuous jet printing has been developed by using Ni nanoparticles mixed with conhesiveness provider. EHD continuous jet printing was used in order to realize $20{\mu}m$ pattern width. Ink stability was investigated by using Turbi-scan which monitors agglomeration and precipitation of nanoparticles in the ink for three days. The Turbi-scan results showed that the formulated Ni ink had been stable for 3 days without any indication of precipitation across the entire ink. Antireflection coating (ARC) layer in crystalline solar cell wafers was removed by laser ablation technique leading to the formation of 84 grooves where the Ni ink was printed by EHD continuous jet printing. The printability and microstructure of EHD-jet-printed Ni lines were investigated by using optical and electron microscopes. 84 Ni lines with the width less than $20{\mu}m$ were successfully printed by one-time printing without any misalignment and fill the laser-ablated ARC grooves.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.9
• /
• pp.6019-6026
• /
• 2015

In this study, we have tried to use 3D-printing technology, which is very useful for small amount production and individual personalization manufacturing to produce a cast customized by individual. To do this, we have made casts by the 3D printer in the method of fused deposition modeling technique using ABS(acrylonitrile butadiene styrene) resin which is thermoplastic plastics. The computed tomography of human hand part was used as the modeling of the cast and it was designed to circulate air well. As a result, an individual personalized cast that fitted well with the model part was produced. In addition, we could get more excellent radiography from the cast than the existing cast. In conclusion, this study of 3D-printing could be used as basic data when a similar designed structure in fused deposition modeling technique by ABS resin is printed out.