• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.8 no.3
• /
• pp.225-230
• /
• 2008

In this paper we embody a system that recognizes printed alphabet, numeral figures and symbols written on the keyboard for the recognition of English sentences. The image of the printed sentences is inputted and binarized, and the characters are separated by using histogram method that is the same as the existing character recognition method. During the abstraction of the individual characters, we classify one group that has not numerical information by the projection of the vertical center of the character. In case of another group that has the longer width than the height, we assort them by normalizing the width. The other group normalizes the height of the images. With the reverse application of the basic principle of the Japanese Puzzle to a normalized character image, the proposed system classifies and recognizes the printed numeral figures, symbols and characters, consequently we meet with good result.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.263-271
• /
• 2010

e-Printing is a new manufacturing technology for electronic products and is based on traditional printing technology. The electronic products require a large area to facilitate printing and to be economical. A gravure printing system that supports a roll to roll (R2R) manufacturing process can be used to reduce the cost and to achieve the required accuracy. Many factors such as drying method, drying temperature, tension,-printing velocity, ink viscosity, ink conductivity, pattern accuracy, and dot geometry influence the performance of printed electronics. These factors are closely interrelated. The optimum condition for printing must be determined to enhance the performance of the printed electronics. In this study, lines and areas are printed using a gravure printer with conductive ink under different conditions of the above mentioned factors. The results are analyzed to investigate the influence of various factors on the performance of the printed electronics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.165-166
• /
• 2011

• Laser Solutions
• /
• v.17 no.4
• /
• pp.20-23
• /
• 2014

In printed electronics, printing rolls are used to transfer electronic ink onto a flexible substrate. Generally printing rolls are patterned in microscale by the indirect laser method. Since based on the wet etch process, the indirect method is neither environment-friendly nor suitable for making a printing roll with patterns narrower than $20{\mu}m$. In this paper, we have directly engraved micro-patterns into a Zn-coated metal specimens using a picosecond laser in order both to engrave $10{\mu}m$-wide patterns and to improve the pattern profile. Experiments showed that it is possible to engrave $10{\mu}m$-wide patterns with an a rectangular-shaped profile which is necessary for the dimensionally accurate printing.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.5
• /
• pp.465-472
• /
• 2016

This study materialized an FPGA-based system to extract PCB patterns. The Printed Circuit Boards that are produced these days are becoming more detailed and complex. Therefore, the importance of a vision system to extract defects of detailed patterns is increasing. This study produced an FPGA-based system that has high speed handling for vision automation of the PCB production process. A vision library that is used to extract defect patterns was also materialized in IPs to optimize the system. The IPs materialized are Camera Link IP, pattern matching IP, VGA IP, edge extraction IP, and memory IP.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.3
• /
• pp.217-223
• /
• 2016

In this research, a continuous roll-to-roll screen printing system was developed using a flat screen. It has a newly devised sliding mechanism of screen printing module, which can be controlled accurately in sync with a moving web, driven by a roll-to-roll tension control and web-guiding system. In addition, the real-time precision alignment module that consists of a vision camera and an $X-Y-{\theta}$ alignment stage was implemented. With this developed system, the feasibility of continuous printing with minimum pattern width below $60{\mu}m$ was verified, and an overlay of ${\pm}60{\mu}m$ between the laser-patterned reference mark and the printed mark on a 300-mm-wide film was achieved.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.18-23
• /
• 1998

Development of an automobile antenna printed on-glass for FM radio receptions was discussed in this study. NEC-2 code was used as the design tool in this research. An omnidirectional radiation pattern and reception power level of the newly designed antenna were compared with those of the conventional pole antenna for the evaluation of its performance. The test sites for the reception power level measurement were chosen by their signal enbironmental condition, such as multipath fading, and strong field effect area.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.16.2-16.2
• /
• 2009

Developing a low cost printing material that can replace silver for the formation of a conducting pattern is an important issue in printed electronics. We report a novel approach using a non-oxidized copper material during the printing and sintering process under ambient conditions, which was previously considered unachievable. An attempt was made to understand the conversion process of cuprous oxide nanoparticle aggregates on metallic copper crystals through chemical reduction in the solution phase. The detailed mechanism for this conversion, including the role of the surfactant and crystal growth, was examined.

• Analytical Science and Technology
• /
• v.28 no.1
• /
• pp.26-32
• /
• 2015

The consistency and homogeneity of repetitive printing of artificial fingerprint were evaluated using a visual minutiae comparison method and an Automated Fingerprint Identification System (AFIS). The standard latent fingerprint pattern was prepared by the printing of a master digital fingerprint pattern with an inkjet printer cartridge case filled with artificial sweat. The master digital fingerprint pattern was prepared with a scanning of an inked fingerprint pattern of a living subject. The intensities of the master digital fingerprint pattern were adjusted by changing the 'output level' values of the Adobe Photoshop CS 5 software. Number of standard latent fingerprint patterns were printed and then developed with conventional latent fingerprint developing methods; ninhydrin treatment method and 1,2-indandion(1,2-IND)/$ZnCl_2$ treatment method. The ridge details of the latent fingerprint patterns developed with the reagents were visually compared with the inked fingerprint pattern and could confirm that the minutiae of both patterns are visually identical. The ridge detail of the inked fingerprint and reagent developed standard latent fingerprint patterns were compared with an AFIS. The average number of minutiae searched by the AFIS was $52.4{\pm}2.4$ (range = 48~56) for 50 ninhydrin developed latent fingerprint patterns, and $50.2{\pm}1.9$ (range = 47~53) for 50 1,2-IND/$ZnCl_2$ developed latent fingerprint patterns. These low standard deviation values over 50 repetitive printing demonstrated that the 50 standard latent patterns were printed with consistent and homogeneous manner.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.245-248
• /
• 2005

In this paper, small sized half-wavelength circular loop antenna which attached beneath a visor of helmet is designed and fabricated at the resonant frequency of 449MHz. To reduce the size of the antenna, double series-shorted stubs are inserted inside the loop for practical use of a vacant space of loop inside. Also, It is designed for the printed type to install the helmet easily. The size of antenna on helmet is reduced to 87.75%(diameter : 70mm, height :.36mm) compare with general type antenna(diameter : 200mm height 101mm). The return loss, -10dB bandwidth and gain are -13.2dB, 17.6MHz(3.9%), and -1.78dBd. And, radiation pattern is omni-directional pattern at H-plane. Therefore, it can be seen that the half-wavelength circular loop antenna using double series-shorted stubs is proper structure for the miniaturization and the installed antenna of the helmet.