• 터널과지하공간
• /
• 제21권6호
• /
• pp.526-535
• /
• 2011

중간주응력을 고려할 수 있는 새로운 콘크리트 파괴조건식을 제안하였다. 제안된 파괴조건식은 Mohr-Coulomb 파괴조건식과 Willam-Warnke의 파괴조건식의 장점을 수용하고 있으므로 자오면에서는 선형파괴식으로 나타나고 팔면체응력면에서는 항상 볼록인 궤적을 보이며 특이성을 갖지 않는다. 진삼축압축시험 결과를 이용한 회귀분석을 통하여 제안된 파괴조건식의 적합성을 검증하였다. 제안된 파괴조건식에 기초한 안전율 공식을 정의하고 이를 파일롯 플랜트에 설치된 콘크리트 플러그의 안전도 해석에 이용하였다. 제안된 안전율 공식은 팔면체응력면에서 응력상태 점의 파괴곡면에 대한 접근도를 의미한다. 마지막으로 플러그의 응력분포를 계산하기 위해 파일롯 플랜트에 대한 3차원 응력해석을 실시하였다. 플러그의 응력분포는 제안된 안전율 공식을 이용하여 안전율 분포로 변환시켰다. 콘크리트 플러그의 안전율 분포특성 분석을 통해 테이퍼형 및 쐐기형 플러그의 안전도를 평가하였다.

• 한국지반공학회논문집
• /
• 제22권10호
• /
• pp.173-181
• /
• 2006

본 논문에서는 정적 및 액상화와 같은 동적하중을 받는 흙의 거동해석을 위한 두 개의 활성면을 가진 구성모델을 제안하였다. 이 모델은 두 개의 활성면에 기초하고 있으며, 첫번째면은 회전하는 최대전단면을 나타내며 두 번째면은 고정된 수평면을 나타낸다. 이와 같은 두 개의 활성면을 이용하여 본 모델은 초기의 다른 응력상태하에 있는 시료의 직접단순전단시에 발생하는 주응력회전현상을 모델링할 수 있다. 제안된 모델은 초기의 응력비에 관계없이 평균유효응력이 동일할 경우에 유사한 거동을 보이는 흙의 실내실험결과를 묘사할 수 있다 그리고, 배수시 반복 직접단순전단으로 발생하는 흙의 거동 즉 제하시에 나타나는 체적감소 및 대변형에서 발생하는 체적팽창을 묘사할 수 있다. 비배수시의 흙의 정적 및 동적 거동은 배수거동에서 흙 골격사이에 존재하는 물의 구속력을 고려함으로써 해석하였다. 본 모델의 구성관계식은 응력-물의 상관관계를 동시에 묘사할 수 있는 FLAC을 이용하여 구현하였다. 배수 직접단순전단 시험을 이용한 Fraser River Sand의 실험결과를 이용하여 모델을 먼저 검증하였으며, 동일한 입력변수를 이용한 Fraser River Sand 비배수 거동의 예측치와 실험치를 비교하여 검증하였다.

• The Journal of Advanced Prosthodontics
• /
• 제16권2호
• /
• pp.77-90
• /
• 2024

PURPOSE. The study aims to investigate the influence of the ferrule effect and types of posts on the stress distribution in three morphological types of the maxillary central incisor. MATERIALS AND METHODS. Nine models were created for 3 maxillary central incisor morphology types: "Fat" type - crown 12.5 mm, root 13 mm, and buccolingual cervical diameter 7.5 mm, "Medium" type - crown 11 mm, root 14 mm, and buccolingual cervical diameter 6.5 mm, and "Slim" type - crown 9.5 mm, root 15 mm, and buccolingual cervical diameter 5.5 mm. Each model received an anatomical castable post-and-core or glass-fiber post with resin composite core and three ferrule heights (nonexistent, 1 mm, and 2 mm). Then, a load of 14 N was applied at the cingulum with a 45° slope to the long axis of the tooth. The Maximum Principal Stress and the Minimum Principal Stress were calculated in the root dentin, crown, and core. RESULTS. Higher tensile and compression stress values were observed in root dentin using the metallic post compared to the fiber post, being higher in the slim type maxillary central incisor than in the medium and fat types. Concerning the three anatomical types of maxillary central incisors, the slim type without ferrule height in mm presented the highest tensile stress in the dentin, for both types of metal and fiber posts. CONCLUSION. Post system and tooth morphology were able to modify the biomechanical response of restored endodontically-treated incisors, showing the importance of personalized dental treatment for each case.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.55-62
• /
• 1999

When stress is beyond elastic limit or cracks occur in a reinforced concrete member subjected to axial force and biaxial bending, curvature about each principal axis of uncracked section is influenced by axial force and bending moments about both major and minor principal axes. It is mainly due to the translation and rotation of principal axes of the cross section after cracking. Recently, by considering these effects, a numerical method predicting the behavior of concrete columns subjected to axial force and biaxial bending was proposed. In this study, in order to verify the proposed numerical method and investigate the effects of cracking on the behavior of reinforced concrete columns, a series of tests were carried out for 16 tied reinforced concrete columns with 100×100 mm square and 200×100 mm rectangular sections under various loading conditions. The angle between the direction of eccentricity and the major principal axis of uncracked section were 0, 30, 40° for the square section and 0, 30, 45, 60, 90° for the rectangular section, respectively. A comparison between numerical predictions and test results shows good agreements in ultimate loads, axial force-lateral deflection relations, and lateral deflection trajectories. It is also found, in this limited investigation, that the ACI's moment magnifier method is conservative in both uniaxial and biaxial loading conditions.

• Geomechanics and Engineering
• /
• 제18권6호
• /
• pp.567-574
• /
• 2019

In order to study the effect of stress and water pressure on the permeability of fractured rock mass under three-dimensional stress conditions, a single fracture triaxial stress-seepage coupling model was established; By using the stress-seepage coupling true triaxial test system, large-scale rock specimens were taken as the research object to carry out the coupling test of stress and seepage, the fitting formula of permeability coefficient was obtained. The influence of three-dimensional stress and water pressure on the permeability coefficient of fractured rock mass was discussed. The results show that the three-dimensional stress and water pressure have a significant effect on the fracture permeability coefficient, showing a negative exponential relationship. Under certain water pressure conditions, the permeability coefficient decreases with the increase of the three-dimensional stress, and the normal principal stress plays a dominant role in the permeability. Under certain stress conditions, the permeability coefficient increases when the water pressure increases. Further analysis shows that when the gob floor rock mass is changed from high stress to unloading state, the seepage characteristics of the cracked channels will be evidently strengthened.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.404-412
• /
• 1991

In the design of high speed machinery, designers must consider the problem of possible structural failure due to excessive dynamically varying stresses, which are induced by the varying external loads and internal inertia forces, in the links of the mechanism. A study of the dynamically induced stresses would indicate what values of the minimum permissible fatigue strength should be for safe mechanism operation. This paper investigates the nature of the stress fluctuation in high speed mechanism on the basis of the effects of both the loads and the friction. The latter is apt to be neglected in the usual analysis in spite of the fact that it is always generated in the operating machinery. The analysis is performed on the coupler of the slider-crank mechanism for illustrative purposes and the results are expressed in a non-dimensional form for design applications.

• Structural Engineering and Mechanics
• /
• 제34권3호
• /
• pp.377-390
• /
• 2010

This paper studies fracture initiation direction of two parallel non-coplanar cracks of equal length. Using the dislocation pile-up modelling, singular integral equations for two parallel cracks subjected to mixed-mode loading are derived and the crack-tip field including singular and non-singular terms is obtained. The kinking angle is determined by using the maximum hoop stress criterion, or the ${\sigma}_{\theta}$-criterion. Results are presented for simple uniaxial tension and biaxial loading. The biaxiality ratio has a noticeable influence on crack growth direction. For the case of biaxial tension, when neglecting the T-stress the crack branching angle is overestimated for small crack inclination angles relative to the largest applied principal stress direction, and underestimated for large crack inclination angles.

• 한국공작기계학회논문집
• /
• 제11권3호
• /
• pp.102-109
• /
• 2002

The fatigue crack growth under mixed mode condition has been discussed within the scope of linear fracture mechanics such as maximum tangential stress, maximum tangential principal stress and minimum strain energy density. The purpose of this study is to investigate the characteristics of fatigue test crack growth in 304 stainless steel under mixed node. The fatigue test results carried out by using inclined pre-crack specimens was compared to both of the theoretical predictions of the criteria, maximum tangential stress and stain energy density. As difference from theoretical analysis, the transition region from mixed mode to mode I appeared in the fatigue test. There is deep relationship between the angle of slanted pre-crack and transition. Therefore, as applying the different stress intensity factor to each node I+II and mode I, the directions and rates of fatigue crack growth are evaluated more accurately under mixed mode.

• 한국안전학회지
• /
• 제10권2호
• /
• pp.120-128
• /
• 1995

The fatigue failure of rail is a principal source of derailment accidents. The reduction of fatigue failures can be achieved by Intensive track maintenance and periodic safety assessments for the railway. For the safety assessments, it is required to have more accurate knowledge for fatigue behavior such as the crack initiation, propagation, crack growth rate and the remaining service life in rail. In this paper, the mean stress effects for the fatigue behavior of rail steel are studied. For this study, the fatigue test is conducted and some equations for fatigue evaluation are applied and compared. From the results, we can see that the fatigue crack growth rate is the more increased as the men stress Is the more increased, the mean stress effect is represented well by the combination of stress intensity factor range and maximum stress intensity factor and Crooker and Range's equation represented by ${\Delta}K, K_{max}$ is the best fit for fatigue evaluation and safety assessment of rail.

• 대한치과보철학회지
• /
• 제23권1호
• /
• pp.97-112
• /
• 1985

The purpose of this study was to evaluate the stress patterns developed in supporting structures by removable partial denture with attachment retainers. The attachments tested were Dalbo(miniature) attachment, resilient Ceka attachment, rigid Ceka attachment, precision and sleeve attachment, and R.P.I. clasp as a contrast. 3-dimensional photoelastic stress analysis was used to record the isochromatic and isoclinic fringe patterns and to calculate principal stress components at measuring points. The results showed that: 1. The maximum compressive stress on residual ridge was produced under the loading point with Dalbo and resilient Ceka attachment, distal to the loading point with rigid Ceka and precision and sleeve attachment, and mesial to the loading point with R.P.I. clasp. 2. The Dalbo attachment produced the most stress on residual ridge, and the least stress on abutment teeth. and resilient Ceka attachment showed favorable stress distribution. 3. Rigid Ceka attachment produced higher compressive stress on buccal. alveolar crest, and precision and sleeve attachment produced higher compressive stress on distal alvelolar crest and mesial surface of the root apex in abutment teeth. 4. R.P.I. clasp produced higher compressive stress on mesial alveolar crest.