• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2136-2146
• /
• 2006

A study on a creep-fatigue crack growth behavior has been carried out for a cylindrical structure with weldments by using a structural test and an evaluation according to the assessment procedures. The creep-fatigue crack growth behavior following the creep-fatigue crack initiation has been assessed by using the French A16 procedure and the conservatism for the present structural test has been examined. The structural specimen is a welded cylindrical shell made of 316 L stainless steel (SS) for one half of the cylinder and 304 SS for the other half. In the creep-fatigue test, the hold time under a tensile load which produces the primary nominal stress of 45 MPa was one hour at $600^{\circ}C$ and creep-fatigue loads of 600 cycles were applied. The evaluation results for the creep-fatigue crack propagation were compared with those of the observed images from the structural test. The assessment results for the creep-fatigue crack behavior according to the French Al6 procedure showed that the Al6 is overly conservative for the creep-fatigue crack propagation in the present case with a short hold time of one hour.

• 한국지반공학회논문집
• /
• 제24권5호
• /
• pp.107-115
• /
• 2008

본 연구는 1차압밀 중의 크리프의 영향과 Yin이 제안한 탄-점-소성 모델에 대한 적용성을 검토하였다. 탄성모델을 이용한 일반적인 압밀이론은, 1차압밀 과정을 표현할 수 있으나 2차압밀을 표현할 수 없다. 이러한 결과는 2차압축을 표현할 수 있는 점성에 기인하며, 때로는 Ladd 등(1977)이 제안한 가정 A 및 B와 같은 스케일효과(실험실 공시체와 현장조건 사이의 점토층 두께의 차이)와 관련되어진다. 통상적으로 1차압밀 중의 크리프의 존재는 많은 연구자에 의해 확인되어졌으며, 가정 B가 잘 맞는 것으로 되어있다. 한편, 대형압밀시험을 통해 가정 A와 B의 중간적인 특성이 Aboshi(1973)에 의한 가정 C로써 제안되어졌다. 본 연구에서는 1차압밀 중의 침하-시간관계에 대한 크리프의 영향을 명백히 하기 위해, peat와 점토에 대해 분할형 압밀시험기를 이용하여 가정 B의 압밀시험을 행하였다. 그리고 Yin의 탄-점-소성 모델을 이용하여 실험결과를 해석하였다. 얻어진 결과는 다음과 같다. 1차압밀 종료시에 분할 공시체의 압축은 과잉간극수압 소산속도의 차이에 의해 동일하지 않았다. 또한 분할형 압밀시험기에 의해 측정된 평균변형률과 Yin의 EVP 모델을 이용한 해석치는 잘 일치하였다. 그러나 과잉간극수압의 소산에 대해서는 측정치가 Yin 모델에 비해 빨리 소산되었다.

• 열처리공학회지
• /
• 제31권3호
• /
• pp.91-96
• /
• 2018

Microstructural development of ferritic 11Cr-3.45W heat-resistance steel for ultra-supercritical power plant during creep and thermal aging was investigated using electron microscopy. The test samples were isothermally aged at $700^{\circ}C$ for up to 4000 hours and subjected to creep loading at $700^{\circ}C$ for predetermined periods of lifetime to prepare the damaged materials. In this structural material, a various secondary phases are the primary influence on mechanical properties of ferritic heat-resistance steel. The typical precipitates of $M_{23}C_6$, MX and $M_2X$ secondary phases had been analyzed through qualitative and quantitative manner. Coarsening of precipitates and increase of lath width were observed during creep and thermal aging. This phenomenon was remarkable for creep process compared with isothermal aging process.

• 연구논문집
• /
• 통권25호
• /
• pp.169-173
• /
• 1995

The high temperature deformation of mechanically alloyed Al-Ti-Si alloy (Al-9.64wt% Ti-1.56wt% Si) was investigated by performing constant load compression creep tests over the temperature range of $673^\circC$K to $723^\circC$K. From the calculation based on the modified power law creep equation for dispersion strengthened alloy, the true creep activation energy, was 176kJ/mole, the true stress exponent was 4.9. Considering the value of activation energy, stress exponent, the shape of primary creep region, it could be concluded that creep deformation in the MA Al-Ti-Si alloy is controlled by dislocation climb.

• 한국주조공학회지
• /
• 제21권4호
• /
• pp.239-245
• /
• 2001

Microstructure and mechanical properties of Sn-3.1 wt.%Ag-6.9 wt.%Bi system solders on Cu-substrate were studied. The Sn3.1 wt.%Ag-6.9 wt.%Bi alloy was designed by phase diagram and chemical properties and was prepared by melting in argon atmosphere. The mechanical properties of solder/Cu joints were examined by shear strength test, and also creep test. The microstructure of Sn-3.1 wt.%Ag-6.9 wt.%Bi alloy consists of Bi-rich phase and $Ag_3Sn$ precipitate in {\beta}-Sn$ matrix phase. The shear strength of the joint was decreased with aging treatment. Crack path under shear test was through the solder. Similar crack path change mode was observed at the creep test of solder/Cu joint. The creep behavior of Sn-3.1 wt.%Ag-6.9 wt.%Bi alloy represented the inverse primary creep behavior at all test condition. It is suggested that the inverse primary creep behavior is induced from Bi solute atoms in Sn-matrix. The creep resistance of Sn-3.1Ag-6.9Bi alloy is better than that of Sn-3.5 wt.%Ag alloy at all test conditions.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.890-897
• /
• 2003

This paper compares engineering estimation schemes of C＊ and creep COD for circumferential and axial through-wall cracked pipes at elevated temperatures with detailed 3-D elastic-creep finite element results. Engineering estimation schemes included the GE/EPRI method, the reference stress method where reference stress is defined based on the plastic limit load and the enhanced reference stress method where the reference stress is defined based on the optimized reference load. Systematic investigations are made not only on the effect of creep-deformation behaviour on C＊ and creep COD, but also on effects of the crack location, the pipe geometry, the crack length and the loading mode. Comparison of the FE results with engineering estimations provides that for idealized power law creep, estimated C＊ and COD rate results from the GE/EPRI method agree best with FE results. For general creep-deformation laws where either primary or tertiary creep is important and thus the GE/EPRI method is hard to apply, on the other hand, the enhanced reference stress method provides more accurate and robust estimations for C* and COD rate than the reference stress method.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.105-111
• /
• 2001

The creep crack growth properties in 3.3NiCrMoV steel were investigated at 55$0^{\circ}C$ by using CT specimen under constant load and constant Ct condition that was held during crack growth of Imm distance. Ct lelied on load line displacement rate, C＊usually increased with crack length though load is reduced in order to maintain constant Ct value as crack growth and appeared scatter band. At constant load and Ct region, crack growth slope was 0.900 and 0.844 each, on the other hand C＊ slope was 0.480. Fully coalesced area(FCA) ahead of crack tip increased as Ct increase to the critical value, and after that value FCA decreased. For the tertiary creep stage of crack growth test, the most of displacement was due to the steady state creep, except only small part due to the primary creep and other effects. Therefore, tests were mainly interrupted in the tertiary stage to obtain high value of Ct.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.501-506
• /
• 2001

The creep crack growth properties in 3.5NiCrMoV steel were investigated at $550^{\circ}C$ by using CT specimen under constant $C_t$ condition that was held during crack growth of 1mm distance. $C_t$ lely on load line displacement rate and $C^*$ usually increase with crack length though load is reduced in order to maintain constant $C_t$ value as crack growth. Fully coalesced area(FCA) ahead of crack tip tend to increase as $C_t$ increase to the critical value, and after that value FCA decrease. For the tertiary creep stage of crack growth test, the most of displacement is due to the steady state creep, except only small part due to the primary creep and other effects. Therefore, tests were mainly interrupted in the tertiary stage to obtain high value of $C_t$. At constant load and $C_t$ region, crack growth slope was 0.900 and 0.844 each, on the other hand $C^*$ slope was 0.480.

• 한국해안해양공학회지
• /
• 제2권2호
• /
• pp.59-66
• /
• 1990

극지방의 해양 환경은 낮은 온도와 함께 여러 가지 형태로 존재하는 얼음의 분포에 의해 큰 영향을 받는다. 빙하와 빙산, 해빙 등 빙역학의 기초적인 이해를 위하여 본 연구는 polycrystalline ice의 재료적 특성과 파괴기구 등을 파악하고 극지 방하유동시 관측되는 creep 변경을 기술하기 위한 constitutive 모델을 제시하였다. 빙변형에 관여되는 여러 가지 물리적 변화 중 microcracking에 의한 재료의 손상을 주요인으로 간주하여 파손역학의 이론을 적용한 3차원 수치모델을 개발하였으며 기발표된 실험 결과와 비교하였다. 1축 균일압축을 받는 경우 실험 데이타와 수치모델은 유사한 거동을 보이고 있으며, 빙변형에 있어서 1, 2기 creep의 소성적 변형특성 뿐 아니라 microcracking에 의한3기(tertiary) creep의 특징까지도 잘 기술해 주고 있다.

• Geomechanics and Engineering
• /
• 제28권2호
• /
• pp.157-169
• /
• 2022

Preloading of soft clays is a common ground stabilization method for improvement of compressibility and the undrained shear strength. The waiting period under preload is a primary design criterion controlling the degree of improvement obtained. Upon unloading the overconsolidation attained with respect to actual loads defines the long term performance. This paper presents a laboratory study for investigation of creep behavior of Famagusta Bay alluvial soft soil preloaded under various effective stresses for analysis of long term performance based on the degree of overconsolidation. Traditional one-dimensional consolidation tests as well as modified creep tests are performed on reconstituted soft specimens. Compressibility parameters are precisely backcalculated using one dimensional consolidation theory and the coefficient of creep is determined using the traditional Cassagrande method as well as two modified methods based on log cycles of time and the inflection of the creep curve. The test results indicated that the long term creep can be successfully predicted considering the proposed method. The creep coefficients derived as part of this method can also be related to the recompression index (recompression index, swelling index) considering the results of the testing method adopted in this study.