• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.75-81
• /
• 1998

This paper is to optimize single-element piezoresistor shear stress strain gauge related to aspect ratio of rectangular diaphragm. The shear stress distribution on diaphragm has been simulated by finite-element method(FEM). As simulation results, the maximum sensitivity for strain gauge was appeared at the center of diaphragm with aspect ratio 3, and in along to long edge with the ratio 2. The diaphragm with ratio 2 is not acceptable due to the yield of mask alignment in IC process technology. The optimum condition of diaphragm with respect to good sensitivity was realized in the case of ratio 3. In this case, the area by gauge was 8% of overall size of rectangular diaphragm.

• Journal of Sensor Science and Technology
• /
• v.14 no.1
• /
• pp.56-61
• /
• 2005

This paper present characteristics of chromium oxide thin-film as piezoresistive sensors, which were deposited on Si substrates by DC reactive magnetron sputtering in an argon-Oxide atmosphere for high temperature applications. The chemical composition, physical and electrical properties and thermal stability ranges of the $CrO_{x}$ sensing elements have studied. $CrO_{x}$ thin films with a linear gauge factor(GF${\fallingdotseq}$15), high electrical resistivity (${\rho}$ = $340{\mu}{\Omega}cm$) and TCR<-55 ppm/$^{\circ}C$ have been obtained. These $CrO_{x}$ thin films may allow high temperature pressure sensor miniaturization to be achieved.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.232-238
• /
• 1999

Single mode fiber optic interferometers using the Fabry-Perot configuration were embedded in a reinforced concrete structure. These interferometers investigated the character of phase shift and strain for internal loads. The 10 mm length of FFPI in the continuous length of single mode fiber (SMF) were produced with two pieces of SMF coated were $TiO_2$ dielectric film utilizing the fusion splicing technique. The fabricated fiber optic Fabry-Perot interferometer(FFPI) and the 6 mm length of steel bar were buried with specimen ($100{\times}100{\times}50\;mm^3$) which was made of concrete structure. The resin protects FFPI and fiber leads from squeezed concrete. Sensors at different point in the structure were multiplexed by TDM (Time Division Multiplexing) method and the deformation to the external loads at each point could be monitored simultaneously. The output signals were proportional to the external loads applied to the structure and the sensitivity of the sensors were $1.03^{\circ}/kg$ and $0.76^{\circ}/kg$ respectively.

• Journal of Biomedical Engineering Research
• /
• v.32 no.4
• /
• pp.312-318
• /
• 2011

The purpose of study was to evaluate effects for repetitive use of thumb according to two different input types (button and touch) of mobile phones. A total of eight young and healthy subjects (6 males and 2 females: $24.63{\pm}8.04$ years) volunteered, and force measurement on thumb using film type pressure sensor was carried out for an hour. Before the experiment De Quervain's syndrome test were performed to check the left and right muscles related with thumb motion and after measuring the pressing force fatigue feeling survey achieved. For a statistical analysis, 1-to-5 ranking scale was used to score the fatigue feeling. From the result of pressure measurement, forces acting on thumb in button type were 3.36 times (the right thumb) and 3.16 times (the left thumb) for the touch type. And the result of survey, fatigue by using the button type of mobile phone was largely triggered than by using touch type. The abductor pollicis brevis and the flexor pollicis brevis were found as common part of fatigue for repetitively using thumb during texting messages. In the further study, some quantitative fatigue comparisons for various input motions are required to analyze repetitive strain injury syndrome.

• Korean Journal of Agricultural Science
• /
• v.40 no.1
• /
• pp.53-59
• /
• 2013

Analysis of load data during field operations is highly important for optimum design of power drive lines for agricultural tractor. Objective of the paper was to analyze field load data using FFT to determine frequency and the energy levels of meaningful cyclic patterns. Rotary tillage, plowing, baling, and wrapping operations were selected as major field operations of agricultural tractor. An agricultural tractor with power measurement system was used. The tractor was equipped with strain-gauge sensors to measure torque of four driving axles and a PTO axle, speed sensors to measure rotational speed of the driving axles and an engine shaft, pressure sensors to measure pressure of hydraulic pumps, an I/O interface to acquire the sensor signals, and an embedded system to calculate power requirement. In rotary tillage, calculated frequency was decreased as travel speed increased. In baler operation, calculated frequency was increased as PTO speed was increased. The calculated peak frequency levels and expected levels were similar. Results of the study would provide information on power utilization patterns and on better design of power drive lines.

• Electronics and Telecommunications Trends
• /
• v.33 no.1
• /
• pp.123-130
• /
• 2018

Tactile sensors, which are commonly referred to as pressure and strain sensors, have been extensively investigated to meet the demands for attachable and wearable electronics for monitoring the health status or activity of human users. For this purpose, the introduction of two-dimensional (2D) materials such as graphene and transition metal dichalcogenides (TMDs) with high mechanical strength at the atomic scale is very suitable for tactile sensors applicable for use in human-friendly devices. In this paper, we examine a descriptive summary of a tactile sensor and review state-of- the-art research trends of 2D material-based tactile sensors in terms of the material and architecture. Finally, we propose a roadmap for future studies into advanced tactile sensors based on our ongoing research.

• Smart Structures and Systems
• /
• v.6 no.8
• /
• pp.975-989
• /
• 2010

Based on the theory of piezo-elasticity, the paper obtains the exact solutions of functionally graded piezoelectric hollow cylinders with different piezoelectric parameter $g_{31}$. Two kinds of piezoelectric hollow cylinders are considered herein. One is a multi-layered cylinder with different parameter $g_{31}$ in different layers; the other is a continuously graded cylinder with arbitrarily variable $g_{31}$. By using the Airy stress function method with plane strain assumptions, the exact solutions of the mechanic and electrical components of both cylinders are obtained when they are subjected to external voltage (actuator) and pressure (sensor), simultaneously. Furthermore, good agreement is achieved between the theoretical and numerical results, and useful conclusions are given.

• Transactions of Materials Processing
• /
• v.31 no.6
• /
• pp.394-403
• /
• 2022

In the automotive industry, cold-drawn austenitic stainless steel is commonly used to handle high fuel pressures in gasoline direct injection (GDI) engines. In this study, we analyzed the effects of main process variables such as cross-sectional shape, drawing speed and friction coefficient on the microstructure, hardness and residual stress of the drawn material in the two-step cold drawing process. By changing the cross-sectional shape in the first-step cold drawing, the possibility of improving the shape accuracy or physical properties of the finally cold-drawn fuel rail pressure sensor product was investigated.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2006.05a
• /
• pp.262-262
• /
• 2006

The characteristics of Brown gas was experimentally studied in view of efficiency and flame propagation. For this study, the Brown gas stack with 7 cells was manufactured following the Brown gas related patents and reports. All measuring equipments were re-tested and calibrated by Korea Laboratory Accreditation Scheme (KOLAS) certified laboratories. Since the amount of produced gas is most crucial in determining the efficiency, we adopted two gas collecting methods such as bottle trap method and wet gas meter method. The energy efficiency of our own fabricated stack was measured to be 75%, which is comparable to general alkaline water electrolysis efficiency. In order to analyze the flame propagation characteristics of Brown gas, we measured the flame propagation pressure, velocity, and shape by using strain type pressure sensor, optical sensor, and high speed camera in conjunction with Schliren system, respectively. From the experimental results, it was found that the flame propagation behavior of Brown gas was almost the same as that of hydrogen and oxygen mixture gas in 2:1 molar ratio. Moreover, from the high speed camera analysis, we concluded that Brown gas flame exhibits explosion behavior as does mixture gas ($H_{2}:O_{2}=2:1$).

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.283-288
• /
• 2005

Application of semiconductor sensors has widely spreaded into various industries because those have several merits like easy miniaturization and batch production comparison with previous mechanical sensors. But external conditions such as thermal and repetitive load have a bad effect on sensors's lifetime. Especially, this paper was focused on fatigue life of a interconnect made by various materials. Firstly we implemented the stress analysis for interconnect under thermal load and wording pressure. And the fatigue lifetime of each material was induced by Manson & Coffin Equation using the plastic stress-strain curve obtained by the plastic-elastic Finite Element Analysis.