• Macromolecular Research
• /
• v.16 no.2
• /
• pp.128-133
• /
• 2008

Several dual-curable acrylic pressure-sensitive adhesives (PSA) were synthesized by the radical polymerization of acrylic monomers containing benzophenone, hydroxyl, and alkyl groups. The optimum extent of UV-induced cure was determined by varying the content of the benzophenone groups (the photoinitiator) from 0.5 to 1.5 wt%. The weight average molecular weight of the polymers obtained ranged from 300,000 to 700,000 amu. The coated pressure-sensitive adhesives were cured either by short UV exposure to induce the grafting of acrylic polymers, or by heating for 6 hat $60^{\circ}C$ to promote the reactions between the polyisocyanates and hydroxyl groups. The dual-curing behavior was determined by monitoring both processes quantitatively by infrared spectroscopy. The developed dual-curable acrylic pressure-sensitive adhesives were found to compensate for the limitations in UV-induced curing of thick coatings.

• Journal of Pharmaceutical Investigation
• /
• v.35 no.3
• /
• pp.173-177
• /
• 2005

Addition of 30% propylene glycol was required to maintain sink condition in the evaluation of percutaneous absorption of estradiol and norethindrone acetate. The permeability of estradiol was higher in silicone and SIS adhesives. However, estradiol was crystallized in silicone, SIS, and SBS adhesive matrix. The permeability ratio of estradiol or norethindrone acetate from acrylic pressure sensitive adhesives varied widely depending on the functional group of the acrylic adhesives. PEO grafting to acrylic adhesive seemed to change physicochemical property of acrylic adhesive and increased the permeability of estradiol and norethindrone acetate significantly. On the contrary, highly cross-linked enhancer compatible acrylic adhesive decreased the permeability of both estradiol and norethindrone acetate. $Span^{\circledR}$ 20 provided the highest enhancing effect on the permeability of both estradiol and norethindrone acetate followed by oleic acid and $Crovol^{\circledR}$ EP40. The permeability of the drugs from the developed system was comparable to that from commercial $Combitran^{\circledR}$, although significantly lower amount of estradiol and norethindrone acetate were loaded in the developed system.

• Elastomers and Composites
• /
• v.51 no.3
• /
• pp.181-187
• /
• 2016

Transparent acrylic pressure sensitive adhesives (PSAs) were successfully prepared by photopolymerization with 2-ethylhexyl acrylate (2-EHA) and 2-hydroxyethyl acrylate (2-HEA) as a default constituent and with isobornyl acrylate (IBOA) and N-(isobutoxymethyl)acrylamide (IBMA) as a variable constituent. The IBMA mole fraction effect in the acrylic PSAs was investigated on adhesion performances and the optical properties including 85/85 test as well as the characteristics (solid content, and molecular weight) of the PSA syrups were also investigated. Regardless increasing the IBMA mole fraction in the acrylic PSAs, the acrylic PSAs exhibited almost the same adhesion performance such as $180^{\circ}$ peel strength (~4.0 kg/25 mm) and probe tack (~0.27 kg). All the acrylic PSA samples also showed high transmittance (more than 91%), low haze (less than 1.0%) and low color-difference (less than 1.0) before and after 85/85 test.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.4
• /
• pp.525-532
• /
• 2008

To prepare a solution type acrylic pressure-sensitive adhesive, quarter polymers were synthesized from butyl acrylate(BA), 2-ethylhexylacrylate(2-EHA) as a base monomer, methyl methacrylate(MMA) as a comonomer, each of methacrylic acid(MAA), acrylic acid(AA) as a functional monomer. Acrylic solution type pressure-sensitive adhesives(PSA's) of isocyanate derivative crosslinking PSA's were prepared by crosslinking of BEMM, BEMA with toluene-2,4-diisocyanate. The structure of adhesive was identified by FT-IR. The viscosity was measured by using Brookfield DV-III and molecular weight was measured by using gel permeation chromatography. The physical properties of polyethylene film coated with BEMMT, BEMAT were measured as a function of the concentration. As the result, BEMMT(0.6, 0.8), BEMAT(0.6) showed peel adhesion of $160{\sim}180\;g_f$/25 mm width and shear adhesion of more than 24 hours, and tackiness of $4/32{\sim}6/32$ which was relevant to commercial usage.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.2
• /
• pp.191-199
• /
• 2005

Removable protective adhesives for automobiles were synthesized by an emulsion polymerization of monomers such as n-butyl acrylate (BA), n-butyl methacrylate (BMA), acrylonitrile (AN), acrylic acid (AA) and 2-hydroxyethyl methacrylate (2-HEMA), in which AA and 2-HEMA were functional monomers. Potassium persulfate (KPS) was used as an initiator and sodium lauryl sulfate (SLS) was used as an emulsifier, and polyvinyl alcohol (PVA) was used as a stabilizer. Emulsion polymerization was carried out in a semi-batch type reactor. Tensile strength, extension, peel strength, viscosity and solid content of the synthesized adhesives were tested. The optimum physical properties of the removable protective adhesives for automobiles were obtained with the composition of 0.43 mole BA, 0.57 mole AN, 0.21 mole BMA, 0.03 mole AA, and 0.03 mole 2-HEMA.

• Journal of Adhesion and Interface
• /
• v.15 no.4
• /
• pp.145-150
• /
• 2014

Dicyclopentadiene (DCPD)-based hydrocarbon resins are widely used as tackifiers in many applications. In particular, hydrogenated DCPD-based hydrocarbon resins are widely used in premium hot-melt-type adhesives such as hot melt adhesives (HMAs) and/or hot melt pressure-sensitive adhesives (HMPSAs), because are water-white in color and possess excellent stability to light and heat. This article discusses the adhesive performance of various hydrogenated DCPD resins when they are used as tackifiers in styrene-block-copolymer (SBC)-based HMPSAs. This article shows the correlation between the characteristics of tackifiers and the adhesive performance of SBC-based HMPSAs. The higher the softening point of the tackifier, the higher is the $T_g$, softening point, and crossover temperature of the PSAs. High aromatic H wt% content reduces the high-temperature resistance of PSAs, as suggested by the decrease in the crossover temperature and softening point of the PSAs.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.95-100
• /
• 2013

In this study, a series of hot-melt pressure sensitive adhesives (HMPSAs) based on metallocene polyolefin (me-PO) were prepared to investigate their possibility of replacing the HMPSAs based on styrenic block copolymers (SBCs). In addition, to optimize the performance of HMPSAs based on me-PO, several tackifiers having different softening point and molecular weight were evaluated. To achieve the HMPSAs which can satisfy the Dahlquist Criterion, hot melts required over 10% of process oil. To obtain the HMPSAs having low viscosity which can be applied by a spraying type applicator, secondary polymer having relatively low crystallinity was required. And, tackifier having high molecular weight attributed to increasing the cohesive strength of me-PO based HMPSAs.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.199-203
• /
• 2014

Terpolymer syrups were photopolymerized from 2-ethylhexyl acrylate, 2-hydroxylethyl acrylate and isobornyl acrylate to prepare acrylic pressure sensitive adhesives (PSAs). After polymerization, various crosslinkers as 1,6-hexanediol diacrylate (HDDA), poly (ethylene glycol) diacrylate (PEGDA, Mn = 250, 575, and 700) were added and then UV-irradiated to prepare the semi-IPN type PSAs. Their adhesion performance and storage modulus (G') were strongly dependent on their chemical structure and molecular weight of the crosslinkers. Optical properties such as transmittance (> 92.5 %), haze (< 1.0 %) and color-difference (< 0.3) of PSAs samples were not affected by crosslinker types used in this study.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.4
• /
• pp.223-228
• /
• 2008

The purpose of this study was to investigate the feasibility of developing transdermal drug delivery system (TDDS) for fentanyl used for the management of chronic cancer pain. The effect of type of pressure sensitive adhesive on the permeation of fentanyl from polyisobutylene (PIB), silicone and acrylic adhesive was evaluated. Due to the good adhesive force and relatively steady flux for 3 days, both acrylic and PIB adhesives were chosen for further study. The permeation rate of fentanyl was the highest from acrylic adhesive with hydroxyl functional group. Permeation rate increased linearly as the concentration of fentanyl in acrylic adhesive was increased from 2.5% to 10%. In case of PIB adhesive, crystals of fentanyl were developed above 5% drug load. $Crovol^{(R)}$ A40, $Crovol^{(R)}$ PK40 and Plurol $oleique^{(R)}$ provided higher flux of fentanyl.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.4
• /
• pp.262-266
• /
• 2000

Acrylic pressure sensitive adhesives of n-butyl acrylate, 2-ethyl acrylate, methyl acrylate, vinyl acetate, acrylic acid, acrylonitrile and 2-hydroxyethyl acrylate were synthesized and basic physical properties of pressure sensitive adhesives with increasing the contents of 2-hydroxyethyl acrylate were investigated. 2-Hydroxyethyl acrylates effects on glass transition temperature, viscosity, hardening time and peel strength. Glass transition temperature(Tg) decreased with increasing the contents of 2-hydroxyethyl acrylate. Viscosity and hardening time were increased with increasing the contents of 2-hydroxyethyl acrylate. On the other hands, peel strength increased with increasing the contents of 2-hydroxyethyl acrylate up to 6 wt% and the decreased at further higher contents of 2-hydroxyethyl acrylate. In peel test, interfacial failure was occured in 8 wt% and 10wt%.