• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.60-64
• /
• 2013

Water injection pump produced the 1st oil well through the high pressure after the Deep water oil well drilling. After finish the work it is hard to produce only using itself pressure due to low pressure. Therefore it can be increased recovery factor through the injection seawater of high pressure. Is the key equipment used in the marine plant and it is developing at many industries. In this paper, Analyze changes in the natural frequency due to the stiffness of the bearing. Analyze the critical speed of the natural frequency due to the change of operation speed. And evaluate the Stability. And then analyze the displacement and clearance through the unbalance response this way has contributed to the reliability of the developing product. Through a mathematical analysis.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1361-1369
• /
• 2003

Design performance of hybrid power generation systems, comprised of a gas turbine and an atmospheric pressure molten carbonate fuel cell, has been analyzed. Two different configurations were analyzed and performances were compared. A reference calculation was performed for the design condition of a system under development and simulated results agreed well with the published data. Performances were analyzed in terms of main design parameters including turbine inlet temperature, operating temperature of the fuel cell and pressure ratio. Also examined were the effects of fuel utilization factor and heat exchanger effectiveness. It was found that the relationship between the turbine inlet temperature and the fuel cell temperature should be critically examined to evaluate achievable design performance. Considering current state of the art technologies, a system with the combustor located before the turbine could achieve higher efficiency and specific power than the other system with the combustor located after the turbine.

• 멤브레인
• /
• 제33권6호
• /
• pp.344-351
• /
• 2023

본 연구에서는 중공사형 이산화탄소 분리막 모듈을 사용하여 수소개질기 배가스로부터 이산화탄소 포집을 목적으로 한 분리막 공정 최적화 연구를 진행하였다. 랩스케일의 소형 분리막 모듈을 사용하여 혼합기체를 대상으로 이산화탄소 순도 90% 및 회수율 90%을 달성하는 2단 공정 조건을 도출하였다. 막 면적이 정해진 모듈의 분리막 공정에서는 스테이지-컷, 주입부 및 투과부 압력에 따라서 포집 순도 및 회수율이 모두 다르게 나타나기 때문에 운전 조건에 대한 최적화가 필수적이다. 본 연구에서는 다양한 운전 조건에서 1단 분리막에서 보이는 공정 포집 효율의 한계를 확인하고, 높은 순도와 회수율을 동시에 달성하기 위한 2단 회수 공정을 최적화하였다.

• 멤브레인
• /
• 제26권5호
• /
• pp.401-406
• /
• 2016

본 연구에서는 역삼투막공정을 이용하여 수용액 중 저준위 방사성이온인 세슘과 요오드 이온을 제거하는 실험을 수행하였다. 국내에서 생산되는 역삼투막모듈 두 가지와 그리고 폐모듈 세정한 후 세슘과 요오드 이온에 대한 제거성능을 비교하였다. 공급수의 농도와 압력을 달리하여 실험을 진행한 결과, 세 가지 모듈 모두 세슘에 비해 요오드의 제염계수가 높은 것을 알 수 있었으며, 특히, 세정한 모듈은 요오드에 대한 제염계수가 1140으로 확인되었다. 대체적으로 실험조건이 고압일 때보다 저압일 때 제염성능이 좋은 것으로 나타났으며 이는 저압조건에 가까운 압력을 갖는 수도수에 직접 모듈을 설치할 경우에도 사용이 가능하리라 판단되었다. 또한 EDTA와 SBS, NaOH, 마이크로버블 등을 사용하여 세정한 막의 제염성능이 세정 전의 제염성능보다 높아졌으며 저압, 저농도 조건에서 요오드에 대한 회수율이 세정 후에 6.3% 증가한 결과를 얻었다.

• 한국지반공학회논문집
• /
• 제31권8호
• /
• pp.5-15
• /
• 2015

불포화 지반에서 선행강우에 의한 강우침투특성을 분석하기 위하여 국내 편마암 풍화토에 대한 일차원 실내강우 침투실험을 수행하였다. 춘천 및 충주지역 시료에 대한 실내모형실험에서 불포화토의 음의 간극수압은 강우 재하시 급격히 감소하고, 강우 종료후 점차 회복되었다. 강우강도가 증가함에 따라 침투속도가 증가하였으며, 선행강우시보다 본강우에서 침투속도가 빠른 것으로 나타났다. 이는 선행강우에 의하여 증가된 지반의 높은 포화도가 본강우시 강우침투속도를 증가시킨 것으로 사료된다. 특히 점토함유량이 많은 충주시료에서 음의 간극수압의 회복 속도와 침투속도가 느리게 나타났다. 유한요소 사면안정에 대한 수치해석 결과는 강우 침투에 의한 음의 간극수압의 감소에 따른 사면 안전율을 감소와 강우 종료후 간극수압의 확산에 의한 추가적인 사면 안정성 저감을 보여주고 있다. 사면의 안전율은 선행강우시 보다 본강우에서 더욱 감소하였다. 선행강우는 불포화지반의 초기 간극수압의 크기와 깊이별 패턴에 지대한 영향을 미치며, 이는 강우 사면의 안정성 해석에 고려해야 할 중요한 요소이다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 제5회 압출 및 인발가공 심포지엄
• /
• pp.43-49
• /
• 2002

A7003 alloy has characteristics of their excellent weldability, high corrosion resistance and superior plastic working however the broadening of application for the alloy has been hampered by the lower extrudability associated by Mg content. For improvement of extrudability and enhanced recovery efficiency during Al scrap recyeling, it has been generally practiced to reduce Mg content in A7003 alloy. Therefore, it is necessary to investigate the influence of Mg content on mechanical strength and extrudability of A7003 alloy. For efficient material processing which has small amounts, life cycle assessment in material processing(MLCA) is evaluated. The quantitative analysis of energy requirements and $CO_2$ emission for production of A7003 extruded bar are estimated with different Mg content and billet pre-heating process (heating source by light oil or LPG). In particular, the estimation of energy requirements was performed within shipping and gating range (except the mining and extraction stages)to investigate the influence of the variables on energy requirements and $CO_2$ emission in detail. As Mg content increased, the flow stress and the extrusion pressure for A7003 alloy increased. It has been thought that an increment in extrusion pressure with increasing Mg content is caused by the solid solution hardening of Mg atoms in the matrix and increment in volume fraction of intermetallic compound, $Mg_2Si$. The extrudability and the tensile strength are equal to, or above that of conventional A 7003 alloy even the content of Mg varied from $1.1wt.\%\;to\;0.5wt.\%$ alloy. This means that minimizing the content of Mg in A7003 alloy can enhance recovery efficiency during Al scrap recycling. It can be quoted that rather than Mg content energy source for billet heating is a prime factor to determine the atmospheric $CO_2$ emission.

• 상하수도학회지
• /
• 제32권4호
• /
• pp.357-361
• /
• 2018

Forward osmosis (FO) process has been attracting attention for its potential applications such as industrial wastewater treatment, wastewater reclamation and seawater desalination. Particularly, in terms of fouling reversibility and operating energy consumption, the FO process is assumed to be preferable to the reverse osmosis (RO) process. Despite these advantages, there is a difficulty in the empirical step due to the lack of separation and recovery techniques of the draw solution. Therefore, rather than using FO alone, recent developments of the FO process have adapted a hybrid system without draw solution separation/recovery systems, such as the FO-RO osmotic dilution system. In this study, we investigated the performance of the hollow fiber FO module according to various operating conditions. The change of permeate flow rate according to the flow rates of the draw and feed solutions in the process operation is a factor that increases the permeate flow rate, one of the performance factors in the positive osmosis process. Our results reveal that flow rates of draw and feed solutions affect the membrane performance, such as the water flux and the reverse solute flux. Moreover, use of hydraulic pressure on the feed side was shown to yield slightly higher flux than the case without applied pressure. Thus, optimizing the operating conditions is important in the hollow fiber FO system.

• Journal of Microbiology and Biotechnology
• /
• 제18권7호
• /
• pp.1317-1325
• /
• 2008

Viral safety is an important prerequisite for clinical preparations of plasma-derived pharmaceuticals. One potential way to increase the safety of therapeutic biological products is the use of a virus-retentive filter. In order to increase the viral safety of human antihemophilic factor IX, particularly in regard to non-enveloped viruses, a virus removal process using a polyvinylidene fluoride membrane filter (Viresolve NFP) has been optimized. The most critical factor affecting the filtration efficiency was operating pH and the optimum pH was 6 or 7. Flow rate increased with increasing operating pressure and temperature. Recovery yield in the optimized production-scale process was 96%. No substantial changes were observed in the physical and biochemical characteristics of the filtered factor IX in comparison with those before filtration. A 47-mm disk membrane filter was used to simulate the process performance of the production-scale cartridges and to test if it could remove several experimental model viruses for human pathogenic viruses, including human hepatitis A virus (HAV), porcine parvovirus (PPV), murine encephalomyocarditis virus (EMCV), human immunodeficiency virus type 1 (HIV), bovine viral diarrhea virus (BVDV), and bovine herpes virus (BHV). Non-enveloped viruses (HAV, PPV, and EMCV) as well as enveloped viruses (HIV, BVDV, and BHV) were completely removed during filtration. The log reduction factors achieved were $\geq$6.12 for HAV, $\geq$4.28 for PPV, $\geq$5.33 for EMCV, $\geq$5.51 for HIV, $\geq$5.17 for BVDV, and $\geq$5.75 for BHV. These results indicate that the virus filtration process successfully improved the viral safety of factor IX.

• The Korean Journal of Physiology and Pharmacology
• /
• 제13권3호
• /
• pp.257-263
• /
• 2009

This study aimed to investigate whether selective serotonin reuptake inhibitors (SSRIs) attenuate brain injury and facilitate recovery following photothrombotic cortical ischemia in mice. Male ICR mice were anesthetized and systemically administered Rose Bengal. Permanent focal ischemia was induced in the medial frontal and somatosensory cortices by irradiating the skull with cold light laser. The animals were treated with fluoxetine or sertraline once a day for 14 d starting 1 h after ischemic insult. Treatment with fluoxetine and sertraline significantly reduced the infarct size. The Evans blue extravasation indices of the fluoxetine- and sertraline-treated groups were significantly lower than that of the vehicle group. Treatment with fluoxetine and sertraline shifted the lower limit of the mean arterial blood pressure for cerebral blood flow autoregulation toward normal, and significantly increased the expression of heme oxygenase-1 (HO-1) and hypoxia-inducible factor-1 ${\alpha}$ (HIF-1 ${\alpha}$) proteins in the ischemic region. These results suggest that SSRIs, such as fluoxetine and sertraline, facilitate recovery following photothrombotic cortical ischemia via enhancement of HO-1 and HIF-1 ${\alpha}$ proteins expression, thereby providing a benefit in therapy of cerebral ischemia.

• 한국항공우주학회지
• /
• 제33권4호
• /
• pp.79-84
• /
• 2005

평판 표면에 충돌하는 축대칭, 과소팽창 제트에 대한 실험적 연구가 수행되어졌으며, 벽압력 및 단열 벽온도 분포가 자세히 측정되어졌다. 벽온도 분포 결과에 대한 설명을 위하여 자유제트 내에서의 전온도 값을 전온도 탐침을 사용하여 측정하였다. 본 연구에서 실험 변수로는 과소팽창비와 노즐-평판간 거리가 고려되었다. 노즐-평판 간 거리에 따라 제트 경계 및 충돌면에서의 에너지 박리에 의해 서로 다른 형태의 단열 벽온도 분포가 나타났으며, 과소팽창비가 큰 경우, 중심영역에서의 저온 유체 입자의 고립효과로 정체점의 회복계수가 크게 낮아지는 현상 또한 관찰되었다.