• 콘크리트학회논문집
• /
• 제23권5호
• /
• pp.581-590
• /
• 2011

초고성능 시멘트 복합체(ultra-high-performance cementitious conposites, UHPCC)는 우수한 압축강도와 연성을 나타내기 때문에 구조 부재 적용 시 단면을 상당히 감소시키고, 낮은 물-결합재비와 고분말 혼화 재료의 사용으로 높은 수축 변형률이 발생하게 되어 거푸집 및 보강근 등의 구속에 의한 수축 균열의 발생 가능성이 크다. 그러므로 이 연구에서는 UHPCC의 수축을 저감시키기 위한 방법으로 팽창재와 수축 저감제를 조합하여 혼입하고 자유수축과 구속 수축 거동을 평가하여 적합성 여부를 산정하였다. 실험 결과 팽창재와 수축 저감제를 조합하여 혼입한 경우에 약 40~44%의 자유수축 저감 효과를 보였으며, 잔류 인장응력은 약 35%와 47% 감소하였다. 지속적인 구속 하중에 의한 인장 크리프의 발생으로 탄성 수축 응력의 약 61%, 64%가 이완되는 것으로 나타났으며, 따라서 구속 수축 거동을 평가할 때에는 반드시 크리프 효과를 고려해야 한다고 판단되었다. 구속도는 0.78~0.85로 나타났으며 팽창재와 수축 저감제의 혼입에 의한 영향은 미미하였고 콘크리트 링의 두께가 클수록 감소하는 경향을 보였다. 또한, UHPCC의 인장 크리프 변형률을 측정하고 재령에 따라 변하는 구속 하중을 적용한 4-매개 변수 크리프 예측 모델과 비교하였다.

• 대한토목학회논문집
• /
• 제32권5A호
• /
• pp.317-325
• /
• 2012

본 연구에서는 초고성능 섬유보강 콘크리트(Ultra High Performance Fiber Reinforced Concrete, UHPFRC)의 구속 상태에서의 수축 거동을 평가하고자 국내 외에서 가장 보편적으로 사용되는 링-테스트(ring-test)를 이용하여 구속 수축 실험을 수행하였다. 특히, 다양한 구속도에서의 수축 거동을 평가하기 위하여 내부 강재 링의 두께와 내부 반경을 달리하여 실험을 수행하였으며, 자유 수축과 인장강도 실험을 수반하여 구속도 및 응력 이완, 수축 균열 가능성 등을 복합적으로 평가하였다. 실험 결과 내부 링의 두께가 증가할수록 내부 링의 평균 변형률과 잔류 인장응력은 감소하였으며, 반면에 구속도는 증가하는 경향을 보였다. 내부 링의 반경에 따라서는 변형률 및 잔류 인장응력, 구속도의 차이가 거의 없는 것으로 나타났다. 모든 시험체에서 잔류 인장응력이 인장강도에 비해 작은 것으로 나타났으며, 수축 균열은 발생하지 않았다. 지속적으로 작용하는 계면 구속 하중에 의해 탄성 수축 응력의 약 39~65%가 이완되는 것으로 나타났으며, 최대 이완 응력은 내부 링의 두께가 두꺼울수록 증가하는 것으로 나타났다. 마지막으로 본 연구에서는 비선형 회귀분석을 수행하여 재령에 따라 변하는 구속도를 예측하였으며, 실험 결과와 잘 일치하는 것으로 나타났다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.401-404
• /
• 2007

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint face, and energy required for welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy, amount of upset, working time, and residual stresses in the joint. Inertia welding was conducted to make the large rotor shaft for low speed marine diesel engine, alloy steel for shaft of 140mm. Due to different material characteristics, such as, thermal conductivity and flow stress, on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters.

• Fibers and Polymers
• /
• 제4권2호
• /
• pp.89-96
• /
• 2003

A vertebral cage is a hollow medical device which is used in spine forgery. By implanting the cage into the spine column, it is possible to restore disc and relieve pressure on the nerve roots. Most cages have been made of titanium alloys but they detract the biocompatibility. Currently PEEK (polyether ether ketone) if applied to various implants because it has good properties like heat resistance, chemical resistance, strength, and especially biocompatibility. A new shape of vertebral cage is designed and injection molding of PEEK is considered for production. Before injection molding of the cage, it is needed to evaluate process conditions and properties of the final product. Variables affecting the shrinkage of the cage are considered, e.g., injection time, packing pressure, mold temperature, and melt temperature. By using the numerical simula-tion program, MOLDFLOW, several cases are studied. Data files obtained by MOLDFLOW analysis are used for stress anal-ysis with ABAQUS, and shrinkage and residual stress fields are predicted. With these results, optimum process conditions are determined.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.204-207
• /
• 2002

The current paper proposes a new multispectral image data compression algorithm that can efficiently reduce spatial and spectral redundancies by applying classified prediction, a Karhunen-Loeve transform (KLT), and the three-dimensional set partitioning in hierarchical trees (3-D SPIHT) algorithm In the wavelet transform (WT) domain. The classification is performed in the WT domain to exploit the interband classified dependency, while the resulting class information is used for the interband prediction. The residual image data on the prediction errors between the original image data and the predicted image data is decorrelated by a KLT. Finally, the 3D-SPIHT algorithm is used to encode the transformed coefficients listed in a descending order spatially and spectrally as a result of the WT and KLT. Simulation results showed that the reconstructed images after using the proposed algorithm exhibited a better quality and higher compression ratio than those using conventional algorithms.

• 천문학회지
• /
• 제50권2호
• /
• pp.21-27
• /
• 2017

The autoregressive method provides a univariate procedure to predict the future sunspot number (SSN) based on past record. The strength of this method lies in the possibility that from past data it yields the SSN in the future as a function of time. On the other hand, its major limitation comes from the intrinsic complexity of solar magnetic activity that may deviate from the linear stationary process assumption that is the basis of the autoregressive model. By analyzing the residual errors produced by the method, we have obtained the following conclusions: (1) the optimal duration of the past time for the forecast is found to be 8.5 years; (2) the standard error increases with prediction horizon and the errors are mostly systematic ones resulting from the incompleteness of the autoregressive model; (3) there is a tendency that the predicted value is underestimated in the activity rising phase, while it is overestimated in the declining phase; (5) the model prediction of a new Solar Cycle is fairly good when it is similar to the previous one, but is bad when the new cycle is much different from the previous one; (6) a reasonably good prediction of a new cycle can be made using the AR model 1.5 years after the start of the cycle. In addition, we predict the next cycle (Solar Cycle 25) will reach the peak in 2024 at the activity level similar to the current cycle.

• 한국세라믹학회지
• /
• 제45권8호
• /
• pp.439-442
• /
• 2008

A series of reaction-sintered SiC was fabricated from preforms with varying volume fractions of two resin-coated SiC particles of different sizes (63 and $18{\mu}m$). The electrical resistivity and mechanical strength were eventually optimized at the small particle volume fraction of $0.3{\sim}0.4$, at which point the porosity of the preform was minimized. This study experimentally proves that additional processes after the formation of the preform, such as silicon infiltration and reaction sintering, do not apparently alter the optimum volume fraction of the preform packing, predicted by an existing analytical model based on solid packing. Thus, the volume fraction of particles of different sizes can be determined practically through the solid packing model to fabricate RSSCs with optimal properties.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1645-1652
• /
• 2002

The failure analysis on fractured parts is divided into the qualitative method by naked eyes and metallurgical microscope etc. and the quantitative method by SEM and X-ray diffraction etc. X-ray fractography can be applied to contaminated surface as well as clean surface and gain the plastic deformation and the residual stress near the fractured surface. Turbine blade is subject to cyclic bending force by steam pressure and suffers fatigue damage according to the increasing operating time. Therefore, to clean up the fracture mechanism of torsion-mounted blade in nuclear plant, the fatigue and the X-ray diffraction test was performed on the 12%Cr steel fur turbine blade and the fractured parts. The correlation of X-ray parameter and fracture mechanics parameter was determined, and then the load applied to actual broken turbine blade was predicted. Failure analysis was performed by contact stress analysis and Goodman diagram of torsion-mounted blade.

• Journal of Advanced Marine Engineering and Technology
• /
• 제10권3호
• /
• pp.94-106
• /
• 1986

Since the oil shock of '70s the engine makers have developed new types of diesel engine with low fuel consumption. There is an obvious tendency towards the use of poorer quality fuels, such as the residual oil from chemical processes of refinery. The shaft driving generators is also widely adopted on behalf of the auxiliary diesel engines, which are driving on the expensive diesel oil and have high fuel oil consumption rates, and some mania propulsion diesel engines are equipped with reduction gear systems to get better propulsive efficiency by slower propeller revolutions. The propulsion shafting system equipped with the shaft driving generator or the geared diesel engine shafting system has flexible couplings, and it requires extensive investigations of the torsional vibration and torque fluctuation in order to ensure the acceptable operation range in service. The characteristics of misfiring must be especially examined for the high viscosity fuels to be used. Both torsional vibration and fluctuating torque resulted from misfiring, should be examined for thier effects on the flexible coupling and propulsion shafting system. This paper is to investigate and solve the above mentioned problems which must be predicted on the design-stage of marine propulsion shafting system. A computer program is developed to calculate the indicated diagram, fluctating torque and torsional vibration for both normal and misfiring conditions.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.935-946
• /
• 2000

Elastic-plastic stress analysis has been performed to evaluate the fatigue life of an autofrettaged pressure vessel containing cross-bores subjected to pulsating internal pressure of 200 MPa. Finite element analyses were used to calculate the residual and operating stress distributions of the pressure vessel due to the autofrettage process and pulsating internal pressure, respectively. Theoretical stress concentration factors of 3.06, 2.58, and 2.64 were obtained at the cross-bore of the pressure vessel due to internal pressure, 50%, and 100% autofrettage loadings, respectively. Local stresses and local strains determined from the elastic-plastic finite element analysis were employed to calculate the failure location and fatigue life of the pressure vessel with radial cross-bores, incorporating the low-cycle fatigue properties of the pressure vessel steel and fatigue damage parameters. Increase in the amount of overstrain by autofrettage process moved the crack initiation location from the inner radius toward a mid-wall, and extended the crack initiation life. Predicted fatigue life of the fully autofrettaged pressure vessel with cross-bores increased about 50%, compared to the unautofrettaged pressure vessel. At the autofrettage level higher than 50%, the failure location and fatigue life of the pressure vessel were not significantly influenced by the autofrettage level.