• Journal of Veterinary Clinics
• /
• v.36 no.6
• /
• pp.301-305
• /
• 2019

Wii^® balance board (WBB, Nintendo, Japan) is a device that can measure and record the center of pressure path length (CPPL) and 95% confidence ellipse area (Area 95) in relation to body sway. For evaluating measure of improvement after reconstruction of medial patellar luxation (MPL) in small sized dogs, A total of 6 dogs with limping and lameness gait attributed to Grade II, III or IV MPL were evaluated. Dogs were measured for difference of extension and flexion range of motion in the stifle (dROM), muscle mass, lameness, willingness to bear weight on the affected limb while standing, and willingness to lift the contralateral limb scores, CPPL and Area 95 of WBB on pre-surgery, post-surgery 4, 8 weeks. CPPL was significantly different on pre-surgery compared with post-surgery 8 weeks (p < 0.05). Except for CPPL, measured variables were significantly different on pre-surgery compared with post-surgery 4 and post-surgery 8 weeks (p < 0.01).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1206-1215
• /
• 2008

In this study, the equivalent pressure acting on the face of drilled hole was determined by back analysis. This analysis was continued until the difference between the displacement directly measured during field test construction of CGS and the displacement evaluated by numerical analysis was below 10 percent, and the affect of diaphragm wall adjacent to grout bulb was evaluated by numerical analysis using the equivalent pressure. From the analysis results, it was observed that the increase of the pressure acting on the diaphragm wall was greater at reclaimed sandfill layer than silty clay layer during the installation of CGS. Two methods were adopted to reduce the pressure acting on the diaphragm wall. One is installing of trench between diaphragm wall and grout bulb, the other is pre-installing of CGS before construction of diaphragm wall. From the numerical analysis results, above two methods can be considered as an effective method to reduce the pressure. It was analyzed that the amount of reduction of the pressure and the displacement are 689.8% and 564.6%, respectively, in the case of adopting the trench method, and 463.7% and 214.0%, respectively, in the case of adopting pre-installing of 3 columns CGS.

• Journal of the Korean Society of Physical Medicine
• /
• v.17 no.2
• /
• pp.95-100
• /
• 2022

PURPOSE: The purpose of this study was to compare the effect of depending on the location of applying chest expansion resistance exercise on the respiratory muscle strength stroke patients, and to suggest more effective interventions to improve respiratory function in stroke patients in clinical practice. METHODS: A total of 30 subjects were selected and divided into two groups, and chest cage extension resistance exercise was applied to the sternum and rib cage, respectively, and performed for 4 weeks, 3 times a week, for 20 minutes. In order to compare the general characteristics of the study subjects and the homogeneity of the group, the pre-experimental values were analyzed using the independent sample t-test. Paired-sample t-test was used for pre-post value comparison of maximum inspiratory pressure and maximum expiratory pressure in each group. Statistical significance was set to .05. RESULTS: Both the sternum application group and the rib cage application group showed a significant difference in the maximum inspiratory pressure according to the intervention. Also, there was a statistically significant difference in the maximum expiratory pressure in the sternum application group. CONCLUSION: As breathing exercise is important for stroke patients, based on the results of this study, if therapists perform sternal extension resistance exercise or rib extension resistance exercise according to the patient's condition and environment, it can help the breathing function of stroke patients.

• Biomedical Science Letters
• /
• v.19 no.1
• /
• pp.55-60
• /
• 2013

This study was to know the effects of massage on the back region in order to reduce stress in middle age women. To investigate the effects of massage to the stress levels of middle aged women, we evaluated blood pressure (BP), heart rate variability (HRV), and ultrasonography before and after back massage. The blood pressure after massage was reduced when compared to that of pre-massage. The HRV spectrum analysis was used Frequency domain analysis such as Mean HRV, normalized low frequency (norm LF), norm high frequency (norm HF), and LF/HF ratio. Post-massage BP tended to be low, but not statistical significant. After Massage, the Mean HRV, norm LF, and LF/HF ratio were significantly reduced, while norm HF was significantly increased as compared with pre-massage. The muscle layer and fat layer were significantly diminished by massage. The study was suggested that massage may be an effective treatment for relief of stress.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.91-96
• /
• 2000

Glass fiber reinforced thermoplastic composites were manufactured by Rapid Press Consolidation Technique(RPCT) as functions of temperature, pressure and time in pre-heating, consolidation and solidification sections during the manufacturing processing. It was found that the material property is greatly affected by pre-heating temperature under vacuum, mold temperature and molding pressure. Among them, the temperature In the mold was the most critical factor in determining the mechanical properties and the molded conditions of specimen. The crystallinity of PET matrix was also investigated by differential scanning calorimetry(DSC) measurements for various processing conditions. The level of crystallinity($X_c$) depended strongly on the mold temperature, cooling rate and the type of composite. The difference in $X_c$ is believed to be one of important factors in characterizing the mechanical properties.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.6 no.2
• /
• pp.9-15
• /
• 2010

US NRC issued rulemaking of 10CFR50.55a to perform the Perservice and Inservice inspection for Reactor Vessel Head Penetration Nozzle of US Nuclaer plant. The rulemaking was required the EPRI Demonstration to verify the NDE technique performing special Ultrasonic examination. In order to meet this requirement, the UT and ECT procedures was demonstrated and the NDE personnel were qualified by EPRI. In this paper, the NDE technique and analysis method are described the Preservice inspection for the Palo Verde #1/2/3 Replacement Reactor Vessel Head Penetration Nozzle using the qualified procedures and personnel.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.767-774
• /
• 1994

The TbFeCo thin films were prepared by the magnetron sputtering system to investigate the effect of the base pressure, film thickness and pre sputtering on the oxidation of the films by analyzing the change of matneto optical properties and by AES depth profile. The films prepared by the facing targets sputtering system represented almost constant magneto optical properties independent of the base pressure resulting from the short flight distance of the sputtered particles. Also, the thin TbFeCo films represented better perpendicular anisotropy as the films thickness increased with pre sputtering. However, it was still needed a deposition rate higher than a certain critical deposition rate to obtain a perfect perpendicular anisotropy even at a very high film thickness.

• Journal of Wind Energy
• /
• v.14 no.3
• /
• pp.109-119
• /
• 2023

A structural safety evaluation was conducted for the stabbing system for the pre-piling jacket substructure currently being developed in South Korea, considering pile construction errors due to its lateral movement that may occur during construction in the ocean. Based on (1) the maximum stress generated by the stabbing system, (2) the maximum rotational displacement of the guide cone, and (3) the maximum stress generated by the horizontal hydraulic pressure cylinder, the structural safety of the stabbing system was examined under the initial loading condition and three possible load combinations during its construction. In order to evaluate the structural safety of the stabbing system, a concept of stress safety factor (= Yield stress / Max. Von-Mises stress) was used. It was found that the stabbing system considered in this study has a sufficient margin of safety.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.1 no.2
• /
• pp.69-76
• /
• 2003

The purpose of this study was to determine the effect of transcutaneous electrical nerve stimulation(TENS) on the alteration of pressure pain threshold of myofascial trigger points. We used fifty nine patients with upper trapezius mayofascial pain syndrome. Participants classified according to each group in conventional TENS(high rate, low intensity) and acupuncture like TENS(low rate, high intensity). The test was measured continuously pre test, post-test by algometer. The following results were obtained; 1. Pressure pain threshold were significantly increased in all groups(p<.001). 2. In comparison between groups, pressure pain threshold were not significantly differenced. These results lead us to the conclusion that each method by TENS were significantly increased pressure pain threshold of upper trapezius trigger points. Therefore, a further direction of this study will be to provide more evidence that TENS method have an effect on pressure pain threshold of myofascial trigger points.

• Journal of Power Electronics
• /
• v.9 no.5
• /
• pp.800-808
• /
• 2009

This paper presents a practical method of pressure control for a hydraulic oil-pump system using an SR (Switched Reluctance) drive. For a 6Mpa grade hydraulic oil-pump, a 2.6kW SR drive is developed. In order to get high performance pressure dynamics in actual applications, a data based PID control scheme is proposed. The look-up table from a pre-measured data base produces an approximate current reference based on motor speed and oil-pressure. A PID controller can compensate for the pressure error. With the combination of the two references, the proposed control scheme can achieve fast dynamics and stable operation. Furthermore, a suitable current controller considering the nonlinear characteristics of an SRM (Switched Reluctance Motor) and practical test methods for data measuring are presented. The proposed control scheme is verified by experimental tests.