• Steel and Composite Structures
• /
• v.17 no.4
• /
• pp.371-386
• /
• 2014

This paper presents a tri-linear restoring force model based on the test results of 12 circular RC columns strengthened by CFRP strips under low cyclic loading. The pre-stress of CFRP strips and axial load ratio of specimens are considered as the affect parameters of the proposed model. All essential characteristics of the hysteretic behavior of the proposed model, including the hysteretic rules, main performance points, strength degradation, stiffness degradation and confinement effects are explicitly analyzed. The calculated results from the proposed model are in good agreement with the experimental results, which shows that the recommended model can be reliably used for seismic behavior predictions of circular RC columns strengthened by pre-stressed CFRP strips.

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.701-712
• /
• 2000

The continuous fiber reinforced composites of GF/PA were fabricated using a pultrusion resin impregnation apparatus and cut into pellets of 6 mm length. GF/PA pellets were then melt-mixed with PP resin to prepare new types of ternary composites, GF/PA/PP. Mechanical and rheological properties of such composites revealed to be better than conventional ternary composites due to the longer average glass fibers. Measurements also showed that the mechanical properties of the composites prepared by direct injection molding were higher than those of the composites prepared by injection molding followed by extrusion. To improve adhesions of fiber surfaces and polymer matrix, PP-MAH (maleic anhydride) has been introduced in the GF/PA/PP composites as a compatibilizer. It was found that PP-MAH did indeed improve surface adhesion between fibers and polymer matrix and that, as a result, various mechanical properties were markedly enhanced. Visualization of the phase structure in the samples was done by means of SEM. The surfaces of glass fibers in GF/PA/PP composites revealed that the fibers remained to be encapsulated by PA resin. However, pre-encapsulation did not persist in GF/PA/PP/PP-MAH composites due to the improvement of surface adhesion between fibers and polymer matrix, although resin sticking to the fiber was observed.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.211-215
• /
• 2005

Stabilization process is absolutely necessary to convert the precursor fibers into chemically, physically, thermally and structurally stable carbon fibers. Especially, it is critically important for rayon fibers experiencing severe weight loss and thermal shrinkage occurring at the stabilization stage below $400^{\circ}C$. The stabilization of rayon fibers strongly depends not only on stabilization temperature but also on heating rate, chemical pre-treatment, atmosphere, and so on. In the present study, the weight loss, fiber diameter change occurred in the furnace during the stabilization process for rayon fibers produced with various heating rates and in the absence and presence of phosphorous-based flame retardants and the thermal stability of the stabilized fibers were investigated. The result indicates that the weight, diameter and thermal stability of the rayon fibers are significantly affected by the type and amount of the flame retardant used. It is also suggested that the pre-treatment of rayon fibers with a concentration lower than $3\;vol\%$ of phosphoric acid is most desirable for further carbonization process of stabilized rayon fibers.

• Macromolecular Research
• /
• v.13 no.1
• /
• pp.2-7
• /
• 2005

A series of ethylene polymerization catalysts based on tridentate bis-imine ligands coordinated to iron and cobalt was reported. The ligands were prepared through the condensation of sterically bulky anilines with allyloxy-and benzyloxy-substituted 2,6-acetylpyridines. The pre-catalyst complexes were penta-coordinate species of the general formula $\{[(ArN=C(Me))_2(4-RO-C_5H_3N)]MCl_2\}$ (Ar=ortho dialkyl-substituted aryl ring; R=allyl, benzyl; M=Fe, Co). In the presence of ethylene and methyl alumoxane cocatalysts, these complexes were active for the polymerization of ethylene, with activities lower than those of metal complexes of the general formula $\{[(2-ArN=C(Me)_2C_5H_3N]MCl_2\}$ (Ar=ortho dialkyl-substituted aryl ring; M=Co, Fe), containing no substituents in 2,6-acetylpyridine ring. The effects of the catalyst structure and temperature on the polymerization activity, thermal properties, and molecular weight were discussed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.153-159
• /
• 2006

Recently, the polymer is used as an admixture in the repair mortar, which contains various admixtures and mineral admixtures. In this study, the fresh and mechanical properties of repair mortar influenced by the types of polymers(classified as E.V.A.) and the range of polymer ratio were investigated. It was found that with increasing the ratio of polymer, mechanical properties(compressive strength, flexural strength, adhesive strength) of repair mortar is improved and drying shrinkage is increased.

• Analytical Science and Technology
• /
• v.37 no.5
• /
• pp.295-305
• /
• 2024

5-Hydroxymethyl-2-furaldehyde (5-HMF) is considered one of the main quality indexes of various food products. Its metabolism in humans can potentially lead to carcinogenic compounds. Metallic ions such as Zn, Mg, Mn, and Fe have been reported to enhance 5-HMF formation. Recently, studies on adsorbents that can extract specific organic and inorganic substances with one adsorbent have been conducted. However, simultaneous analysis of organic and inorganic materials typically requires distinct pre-treatment and analytical methods, which increase a lot of labor and cost. In this study, hybrid imprinted polymer (HIP) by mixing 5-HMF imprinted polymer (FIP) and zinc ion imprinted polymer (ZIIP) were generated to extract two analytes, Zn ion and 5-HMF, simultaneously. Physicochemical characterization of HIP was conducted by Fourier-transform infrared spectroscopy, scanning electron microscopy, and sorption tests. Extraction conditions including adsorbent mixing ratio, adsorbate mixing range, and equilibrium time were optimized. Freundlich adsorption model was as the best-fitting isotherm model to elucidate the adsorption mechanism. Affinity of Zn ion and 5-HMF on HIP was superior to non-HIP. In conclusion, HIP showed reasonable feasibility that could be used as an adsorbent to be used for simultaneous extraction of organic and inorganic compounds present in the sample.

• Resources Recycling
• /
• v.24 no.1
• /
• pp.43-50
• /
• 2015

An extensive literature survey and personal communication with relevant experts made it possible to understand economic and technical feasibility of disposable diaper recycling. Commercial level of soiled diaper recycling technology is currently available from a Dutch company, Knowaste Co., who owns a proprietary separation technology of the pulps, plastics and super absorbing polymer (SAP). In Korea, on the other hand, pre-consumer diaper recycling technology without material separation at its infancy converts manufacturing scraps into refuse plastic fuel (RPF), container/truck cargo boards or automobile boards/sheets. Although previous studies on feasibility of post-consumer recycling in Korea showed mutually contradictory implication, it was found out in this research that significantly positive economic feasibility can be obtained with pre-consumer diaper recycling. Subsequent recycling R&D including pre-consumer scrap and policy support may expedite 'Establishment of Sustainable Society.

• Journal of Environmental Science International
• /
• v.12 no.7
• /
• pp.801-807
• /
• 2003

This work aims the search of environmentally friendly pre-treatment technologies to develop chromate replacements for metal finishing industries due to its toxicological properties. Since the corrosion resistance of steel was strongly related to water permeation, galvanized steel sheets were treated with various hydrophobic silane compounds and water-suspended polymer solution. Also, plasma gas discharge was applied to modify the surface of a polymer coated-steel sheet to be hydrophobic. The surface hydrophobicity of materials was introduced by CF$_3$H plasma exposure. The corrosion property before and after the plasma treatment was investigated in a slat spray tester with 3.5 wt.% NaCl at 35$^{\circ}C$. The results showed that both silane/polymer double coatings and plasma treatment of the galvanized steel exhibited significant retardation of corrosion.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.399-402
• /
• 2005

We have studied the Pixel Isolated Phase Separated Composite Organic Film (PI-PSCOF). The PI-PSCOF can be made by the anisotropic phase separation between Ferroelectric Liquid Crystals and Pre-polymer materials by irradiating the UV with optimizing its intensity and time. In the technology, the FLC molecules are isolated in pixels where FLCs are surrounded by the inter-pixel vertical polymer walls and the horizontal polymer films on the upper substrate. The good merits of this technology are fast response time, and good mechanical and thermal stability against external high pressure and temperature. We will compare the results obtained from FLC, PSCOF, and PI-PSCOF modes by using the electro-optic measurement and x-ray scattering, and mechanical method. We believe that the PI-PSCOF technology can be a best candidate for future Flexible Display Applications.

• The Journal of the Korean dental association
• /
• v.53 no.3
• /
• pp.178-186
• /
• 2015

Dental polymer-based luting materials are classified into esthetic resin cement, adhesive resin cement and self-adhesive resin cement. Due to the different component of each type of resin cement, the preconditioning method of tooth surface and the steps are different from each type of resin cement. The pre-treatment of adherend (ceramic, resin and metal) surface also varies with the type of resin cement and the manufacturer. In this study, the characteristics of each type of resin cement, mechanical properties, indication and advantages were investigated. Through these, clinical tips on using resin cements were suggested.