• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1144-1145
• /
• 2006

In this paper, the fundamental attributes, phase composition of three pre-alloyed powders for diamond tools by water atomization were investigated. The density, hardness, bend strength and bending modulus of their hot pressing samples were examined. The results showed that the three pre-alloyed powders have excellent low temperature sintering characteristics. The physical and mechanical properties of the samples were found to be nearly the same as those of fine cobalt powders.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.280-281
• /
• 2006

Powder grades pre-alloyed with 1.5-3 wt% chromium can be successfully sintered at the conventional temperature $1120^{\circ}C$ although well-monitored sintering atmospheres are required to avoid oxidation. Mechanical properties of the Cr-alloyed PM grades are enhanced by a higher sintering temperature in the range $1120-1250^{\circ}C$, due to positive effects from pore rounding, increased density and more effective oxide reduction. Astaloy CrM (Fe-3 wt% Cr-0.5 wt% Mo) with 0.6 wt% graphite added obtains an ultimate tensile strength of 1470 MPa and an impact strength of 31 J at density $7.1\;g/cm^3$, after sintering at $1250^{\circ}C$ followed by cooling at $2.5^{\circ}C/s$ and tempering.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1185-1186
• /
• 2006

In order to obtain specific magnetic properties, it is of paramount importance to increase the alloy density of components fabricated by powder metallurgy. An alternative to increase the density of alloys such as Fe-49Co-2V would be the use of elemental Fe and Co instead of the pre-alloyed powder. Trying to give some insight on the industrial application of this strategy, this paper investigates the replacement of more conventional pre-alloyed Fe-49Co-2V powders with elemental Fe and Co. A previous analysis shows that it is possible to achieve higher densities and leads to a noticeable improvement in some important magnetic properties.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.10a
• /
• pp.99-100
• /
• 2003

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.138-139
• /
• 2006

Sintered steels are materials characterized by residual porosity, whose dimension and morphology strongly affect the fatigue crack growth behaviour of the material. Prismatic specimens were pressed at $7.0\;g/cm^3$ from Astaloy CrM powder and sintered varying the sintering temperature and the cooling rate. Optical observations allowed to evaluate the dimensions and the morphology of the porosity and the microstructural characteristics. Fatigue tests were performed to investigate the threshold zone and to calculate the Paris law. Moreover $K_{Ic}$ tests were performed to complete the investigation. Both on fatigue and $K_{Ic}$ samples a fractographic analysis was carried out to investigate the crack path and the fracture surface features. The results show that the Paris law crack growth exponent is around 6.0 for $1120^{\circ}C$ sintered and around 4.7 for $1250^{\circ}C$ sintered materials. The same dependence to process parameters is not found for $K_{Ith}$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.132-133
• /
• 2006

Optimized choice of material for two principally different types of PM components is presented. The first is characterized by high stresses in areas with high stress concentrations (for example synchronizer hubs with very sharp notches, typically <0.25mm in the pre-synchronizer slot and the inner splines). The second type has slightly larger notch radii (small spur gears and sprockets with typically notch radii between 1- 3mm). Diffusion alloyed materials are well suited for sharp notch components. Pre-alloyed materials are also well suited for applications with sharp notches if compressive residual stresses in the notch roots are created by appropriate process control. A free choice of material is available for components with the larger notch radii.

• Journal of Powder Materials
• /
• v.28 no.5
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1296-1297
• /
• 2006

Both plastic and elastic properties change dramatically from the beginning to the end of the compaction phase. Previous investigations have shown that powder transfer and high powder flow during initial compaction at low density affects the strength of the final component significantly. Investigated here are shear failure and elastic shear modulus in the low density range for hard metal powder and for pre-alloyed water atomized iron powder. Direct shear test equipment for sand and clay has been modified to measure the shearing properties of powder for an axial loading between 1 kPa and 500 kPa.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.769-770
• /
• 2006

The MIM industry is currently focusing on parts that are used in automobiles and medical instruments. Many of the parts in these categories are very small and often not easy to machine because of its complex geometry. Therefore MIM is well suited for the production of these parts. We tested the sinterability of SUS316L ultra fine powders (3,4, 6, 8micron) produced by ATMIX high-pressure water-atomization, and it showed excellent results. A density of 97% theoretical was obtained by sintering at 1373K when using the ultra fine powder (3micron). Specifically, the finer the powder size, higher was the sintered density. The surface roughness and accuracy are also greatly improved with ATMIX ultra fine powder.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.22-23
• /
• 2006

High velocity compaction (HVC) is a production technique with capacity to significantly improve the mechanical properties of powder metallurgy (PM) parts. Investigated here are green body data such as density, tensile strength, radial springback, ejection force and surface flatness. Comparisons are performed with conventional compaction using the same pressing conditions. Cylindrical samples of a pre-alloyed water atomized iron powder are used in this experimental investigation. The HVC process in this study resulted in a better compressibility curve and lower ejection force compared to conventional quasi static pressing. Vertical scanning interferometry measurements show that the HVC process gives flatter sample surfaces.