• 전산구조공학
• /
• 제1권1호
• /
• pp.113-122
• /
• 1988

본 연구에서는 강도로교의 피로파손의 위험을 예측할 수 있는 실용적 모형을 개발하였다. 제안된 피로해석 모형은 피로신뢰성 이론과 교량의 피로수명에 영향을 미치는 여러가지 요인들을 고려하여 유도되었다. 피로신뢰성 함수는 Weibull분포로 가정하였고, Weibull의 수치계산형태는 강재의 피로수명과 변진폭재하로 인한 응력범위 등의 통계적 불확실량을 모두 포함하는 Ang-Munse의 식을 사용하였다. 피로해석모형에는 교량이용 기간중에 발생할 수 있는 일평균교통량(ADTT)의 변화, 재하이력의 변화, 진추조사의 효과 등을 고려하였다. 응력범위 주상도는 개설 교량에 대한 현장실측결과로부터 구한 랜던 응력파로부터 작도하고, 그 결과 구해지는 응력범위분포는 Beta분포로 모형화 하였다. 본 연구에서 제안한 피로해석 방법을 실제 개설 교량에 대해 적용한 결과, 제안된 피로해석모형과 수치계산을 위하여 개발된 전산프로그램은 기설 노후 강교의 피로 내하력 판정이나 잔존수명의 예측 등을 위한 실용적인 방법으로 사용될 수 있다고 생각된다.

• 한국정밀공학회지
• /
• 제18권1호
• /
• pp.111-116
• /
• 2001

A practical scheme to reduce failure of the PCB(Printed Circuit Board) of a monitor is introduced using deformed mode shape under mechanical shock. When the monitor is given critical shock loads, cracks are commonly initiated at the tip of a hole on the PCB. Accordingly, a deformed mode shape of the PCB is obtained using a FEM code to define a weak point on the PCB under mechanical shock, and then the position and direction of the hole is determined to prevent the failure at the critical mode shape. Also, the stress intensity factor around the weak point on the PCB is calculated to check the possibility of fracture by normal tensile stress. In conclusion, present research is useful to assist the practical design of components-layout on the PCB.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.2953-2959
• /
• 2021

A new practical modeling of the Norton's power law creep is proposed and implemented to analyze the high temperature behaviors of Alloy 690 SG tube material. In the model, both the stress exponent n and the rate constant B are simply treated as the temperature dependent parameters. Based on the two-step optimization procedure, the temperature function of the rate constant B(T) was determined for the data set of each B value after fixing the stress exponent n value by using the prior optimized function at each temperature. This procedure could significantly reduce the numerical errors when using the power law creep equations. Based on the better description of the steady-state creep rates, the experimental rupture times could also be well predicted by using the Monkman-Grant relationship. Furthermore, the difference in tensile strengths at high temperatures could be very well estimated by assuming the imaginary creep stress related to the given strain rate after correcting the temperature effects on the elastic modulus.

• 대한간호학회지
• /
• 제19권2호
• /
• pp.203-211
• /
• 1989

The purpose of this study is the extent of the stress of the nursing students during the period of delivery room practice, according to whether they have their practical experience and in which situations they received. The subject of this study is 62 nursing students (who experienced delivery room pracice at an early stage) in Kang Weon C. Junior College of nursing and 62 nursing students(who experienced delivery room practice at a latter stage) in J.Junior college of Nursing (total 124 students) from March 1988 to December 1988. The results of this study are summerized as follows. 1. According to the general characteristics, it revealed that they have not any relations between the religion, the numbers of family, health status and the extent of stress during the nursing students have experienced in the delivery room practice(p＞.05). 2. It revealed that there were much differences to the extent of stress they have experienced during the delivery room practice between the nursing students(who experienced delivery room practice at an early stage) in C.Junior College of Nursing and nursing students(who experienced delivery room practice at a latter stage) in J. Junior College of Nursing(p＜.000). 3. In ten items of the stress that was confronted by nursing practice, they had much differences to the extent of stress perception for the students during the period of delivery room practice between each college(p＜.05). 4. In the four parts of the clinical practice except for adult nursing practice, they had much differences to the extent of stress according to whether they have their practical experience. However the stress which they experienced in the adult ward during the period of delivery of delivery room nursing practice is too low to be significant(p＜.05).

• 오토저널
• /
• 제15권3호
• /
• pp.111-119
• /
• 1993

In this study, the transient impact structural stress analysis of tracked vehicle structures under recoil impact load is investigated. ANSYS, ABAQUS Code are used for modelling and analytical procedures. The highest maximum Tresca stress occurs on race ring portion and its stress level is (.sigma.$_{T}$)$_{max}$ =20-40kgf/m $m^{2}$. The second highest stress occurs on upper plate of chassis and down plate of turret. The maximum stress level increases with loading direction and elevation angle. The results from liner static load analysis are very much different with impact analysis. Therefore, the practical solutions of structures under impact load can be obtained by only nonlinear transient impact analysis. The impact stress analysis of the steel vehicle structures is conducted. The maximum stress level is less than (.sigma.$_T/)$_{max}$m $m^{2}$. So, the design concept of steel structures can be adapted for new alternatives.s.s.s..s.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.103-108
• /
• 2000

Since the ceramic/metal joint material is made at a high temperature, the residual stress development when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of $Si_3N_4/STS304$ joints quantitatively and to compare the strength of Joints. The difference of residual stress is measured when repeated thermal cycle is loaded under the conditions of the practical use of the ceramic/metal joint. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a residual it is known that the stress of joint decreases as the number of thermal cycle increases.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3227-3235
• /
• 1994

This paper deals with an evaluation of the residual stress due to shot peening induced in a carburized gear tooth and its application to the fatigue crack propagation problem. A practical method is proposed on the basis of the assumption that the residual stress is caused by the difference of volume expansion in the case and the core, and the influence of both the reduction of retained austenite and the strain due to shot peening are considered. The evaluated residual stress is close to the measured stress, though the surface stress is rather overestimated. The stress intensity factor is computed by the influence function method, and it is shown that the factor is decreased by the residual stress in shot peened gear tooth. The shot peening is fairly effective to the reduction of fatigue crack growth rate. The crack propagation is simulated and the resistance due to shot peening is quantitatively demonstrated and discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.170-177
• /
• 2003

This paper proposes a robust method for the Ramberg-Osgood (R-O) fit to accurately estimate elastic-plastic J from engineering fracture mechanics analysis based on deformation plasticity. The proposal is based on engineering stress-strain data to determine the R-O parameters, instead of true stress-strain data. Moreover, for practical applications, the method is given not only for the case when full stress-strain data are available but also for the case when only yield and tensile strengths are available. Reliability of the proposed method for the R-O fit is validated against detailed 3-D Finite Element (FE) analyses for circumferential through-wall cracked pipes under global bending using five different materials, three stainless steels and two ferritic steels. Taking the FE J results based on incremental plasticity using actual stress-strain data as reference, the FE J results based on deformation plasticity using various R-O fits are compared with reference J values. Comparisons show that the proposed R-O fit provides more accurate J values for all cases, compared to existing methods for the R-O fit. Advantages of the proposed R-O fit in practical applications are discussed, together with its accuracy.

• 대한기계학회논문집A
• /
• 제27권9호
• /
• pp.1571-1578
• /
• 2003

This paper proposes a robust method for the Ramberg-Osgood(R-O)fit to accurately estimate elastic-plastic J from engineering fracture mechanics analysis based on deformation plasticity. The proposal is based on engineering stress-strain data to determine the R-O parameters, instead of true stress-strain data. Moreover, for practical applications, the method is given not only for the case when full stress-strain data are available but also for the case when only yield and tensile strengths are available. Reliability of the proposed method for the R-O fit is validated against detailed 3-D Finite Element (FE) analyses for circumferential through-wall cracked pipes under global bending using five different materials, three stainless steels and two ferritic steels. Taking the FE J results based on incremental plasticity using actual stress-strain data as reference, the FE J results based on deformation plasticity using various R-O fits are compared with reference J values. Comparisons show that the proposed R-O fit provides more accurate J values for all cases, compared to existing methods for the R-O fit. Advantages of the proposed R-O fit in practical applications are discussed, together with its accuracy.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.107-115
• /
• 2001

It is required more precise analysis for practical load because of complexities and varieties of vehicle structure. To establish the numerical model, many researchers have been developed designing tools for linking F.E. Analysis results and experimental results. There studies have generally focused on each experimental method or analytical method separately. There are few studies based on both methods. This paper conceives new procedure for the determination of the load direction and magnitude applied on mechanical structures. New procedure is the combination of the analytical and empirical method with analyzed strain by F.E. Analysis under unit load and with measured principal stress by strain gages under driving load, respectively. In this paper, we theorize the procedure of practical load determination and make the validity and the practicality of the procedure with the application to T-shape jointed structure. F.E. Analysis is conducted to get the principal stress on arbitrary points in the F.E. model of T-shape joint under unit load. Then experiment is carried out to get the principal stress on the same points of F.E. model. To demonstrate the actual driving condition, the load conditions are bending and torsion. From these two data sets, the magnitude, the direction and the position of load can be obtained. Theory and practice do not always coincide; since there are some errors such as ill-poseness, measuring error and modeling error in experimental data, we examine the proper method of error minimization.