• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1128-1132
• /
• 2002

$ReMnO_3$(Re:Y, Ho, Er) thin films were prepared by MOCVD method available to non-volatile memory device with MFS-FET structure. $ReMnO_3$ thin films were deposited on the Si(100) substrate at 700${\circ}C$ for 2h. When the films were post-annealed at 900${\circ}C$ for 1h in air, the single phase of hexagonal $ReMnO_3$ thin films were detected. Ferroelectric properties of $ReMnO_3$ thin films were dependent on the degree of c-axis orientation in the single phase of hexagonal structure and remnant polarization (Pr) of $YMnO_3$ thin films with high degree of c-axis orientation was 105 nC/$cm^2$. Leakage current density was dependent on the grain size of microstructure and that of $YMnO_3$ thin films with grain size of 100∼150 nm was $10^{-8}$ A/$cm^2$ at applied voltage of 0.5 V.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.15-22
• /
• 2023

BNKT Ceramics, one of the representative Pb free based piezoelectric ceramics, constitutes a perovskite(ABO3) structure. At this time, the perovskite structure (ABO3) is in the form where the corners of the octahedrons are connected, and in the unit cell, two ions, A and B, are cations, A ion is located at the body center, B ion is located at each corner, and an anion O is located at the center of each side. Since Bi, Na, and K sources constituting the A site are highly volatile at a sintering temperature of 1100℃ or higher, it is difficult to maintain uniformity of the composition. In order to solve this problem, there should be suppression of volatilization of the A site material or additional compensation of the volatilized. In this study, the basic composition of BNKT Ceramics was set to Bi_0.5(Na_0.78K_0.22)_0.5TiO₃ (= BNKT), and volatile site (Bi, Na, and K sources) were coated in the form of a shell to compensate additionally for the A site ions. In addition, the physical and electrical properties of BNKT and its coated with shell additives(= @BNK) were compared and analyzed, respectively. As a result of analyzing the crystal structure through XRD, both BNKT(Core) and @BNK(Shell) had perovskite phases, and the crystallinity was almost similar. Although the Curie temperature of the two sintered bodies was almost the same (TC = 290 ~ 300 ℃), it was confirmed that the d33 (piezoelectric coefficient) and Pr (residual polarization) values were different. The experimental results indicated that the additional compensation for a shell additive causes the coarsening, resulting in a decrease in sintering density and Pr(remanent polarization). However, coating shell additives to compensate for A site ion is an effective way to suppress volatilization. Based on these experimental results, it would be the biggest advantage to develop an eco-friendly material (Lead-free) that replaced lead (Pb), which is harmful to the human body. This lead-free piezoelectric material can be applied to a biomedical device or products(ex. earphones (hearing aids), heart rate monitors, ultrasonic vibrators, etc.) and skin beauty improvement products (mask packs for whitening and wrinkle improvement).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.7-15
• /
• 2004

The ferroelectric SBT thin films as a material of capacitors for non-volatile FRAMs have some problems that its remanent polarization value is relatively low and the crystallization temperature is quite high abovc 80$0^{\circ}C$. Therefore, in this paper, SBTN solution with S $r_{0.9}$B $i_{2.1}$T $a_{1.8}$N $b_{0.2}$$O_{9}$ composition was synthesized by sol-gel method. Sr(O $C_2$ $H_{5}$)$_2$, Bi(TMHD)$_3$, Ta(O $C_2$ $H_{5}$)$_{5}$and Nb(O $C_2$ $H_{5}$)$_{5}$ were used as precursors, which were dissolved in 2-methoxyethanol. SBTN thin films with 200 nm thickness were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. UV-irradiation in a power of 200 W for 10 min and rapid thermal annealing in a 5-Torr-oxygen ambient at 76$0^{\circ}C$ for 60 sec were used to promote crystallization. The films were well crystallized and fine-grained after annealing at $650^{\circ}C$ in oxygen ambient. The electrical characteristics of 2Pr=11.94 $\mu$C/$\textrm{cm}^2$, Ps＋/Pr＋=0.54 at the applied voltage of 5 V were obtained for a 200-nm-thick SBTN films. This results show that 2Pr values of the UV irradiated and rapid thermal annealed SBTN thin films at the applied voltage of 5 V were about 57% higher than those of no additional processed SBTN thin films. thin films.lms.s.s.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.56-62
• /
• 1997

Using a rf-magnetron sputtering method, highly c-axis oriented La modified $PbTiO_{3}$ (PLT) ferroelectric thin films with compositions of $(Pb_{1-x}La_{x})Ti_{1-x/4}O_{3}$, where x=0.05, x=0 and x=0.15, have been obtained on (100)MgO single crystal substrate under conditions of low gas pressure. The degree of c-axis orientation of PLT films decreases with increasing gas pressure and with increasing La contant. These films were characterized by X-ray diffraction and SEM. PLT thin films of x=0.05, 0.1 and 0.15 show a low dielectric constant of 218, 246 and 361 at 1 kHz and remanent polarization(Pr) of $9{\mu}C/cm^{2}$, $8{\mu}C/cm^{2}$ and $7{\mu}C/cm^{2}$.

• Electrical & Electronic Materials
• /
• v.9 no.3
• /
• pp.251-258
• /
• 1996

Sol-Gel derived ferroelectric Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_{3}$ thin films have been fabricated on Pt/Ti/ $SiO_{2}$/Si substrate. Two kinds of fast annealing methods, F-I (six times of intermediate and final annealing) and F-II(one final annealing after six times of intermediate annealing) were used for preparation of multi-coated PZT thin films. As the annealing temperature was increased, high capacitance could be obtained, for instance, 2700.angs.-thick PZT thin film annealed at 680.deg. C had a capacitance value of approximately 20nF at 1kHz. In addition, it is found that the dielectric constant is a function of the perovskite phase fraction. In case of F-I method, PZT thin film had a remanent polarization(Pr) of 8-15.mu.C/c $m^{2}$ and a coercive field( $E_{c}$) of 35-44kV/cm according to annealing temperature, whereas PZT film fabricated by F-II method had as high as 24-25.mu.C/c $m^{2}$ and 48-59kV/cm, respectively. As a result of measuring Curie temperature, PZT thin film had a range of 460-480.deg. C by F-I method and more or less higher range of 525-530.deg. C by F-II method, which implied that different microstructures could cause the different Curie temperature. Through I-V measurement, leakage current of PZT thin film fabricated by F-I and F-II methods was 64nA/c $m^{2}$ and 2.2.mu.A/c $m^{2}$ in the electric field of 100kV/cm, respectively.y.y.y.

• Korean Journal of Materials Research
• /
• v.13 no.5
• /
• pp.317-322
• /
• 2003

Bismuth layered structure ferroelectric thin films, $Bi_4$$Ti_3$$O_{12}$ / (BTO) and Nb-doped BTO (BTN) were prepared on the Pt(111)/Ti/$SiO_2$/Si(100) substrates by a sol-gel route. We investigated the Nb-doping effect on the grain orientation and ferroelectric properties. $Nb^{5＋}$ ion substitution for $Ti^{4＋}$ ion in perovskite layers of BTO decreased the degree of c-axis orientation and increased the remanent polarization (2Pr). The fatigue resistance of Nb-doped BTO thin film was shown to be superior to that of BTO, and the leakage current of Nb-doped BTO thin film was decreased about 1 order of magnitude compared with BTO. The improvement of ferroelectric properties with $Nb^{5＋}$ doping in BTO could be attributed to the changes in space charge densities and grain orientation in the thin film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.272-278
• /
• 2003

$Bi_4Ti_3O_{12}$ (BIT) and $(Bi_{3.25}La_{0.75})(Ti_{2.97}V_{0.03})O_{12}$ (BLTV) thin films were deposited on ITO/glass substrates by metal organic chemical vapor deposition (MOCVD) using ultrasonic spraying. After deposition of the films in oxygen atmosphere for 30 min, the films were heated by rapid thermal annealing (RTA) method, especially direct insertion, at various temperatures. The films were investigated on phase formation temperature, microstructure and electrical properties. From x-ray diffraction (XRD) patterns, the perovskite phase formation temperature of BLTV thin film was about $600^{\circ}C$ which was lower than that of BIT, $650^{\circ}C$. The leakage current of the BLTV thin film was measured to be $1.52\times 10^{-9}$A/$cm^2$ at an applied voltage of 1 V. The remanent polarization (Pr) and coercive field (Ec) values of the BLTV film deposited at $650^{\circ}C$ were $5.6\muC/cm^2$ and 96.5 kV/cm, respectively.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.36-43
• /
• 1997

FECAPS(ferroelectric capacitors) have been fabricated by RF magnetron sputtering deposition of 3000$\AA$ PZT thin films on the Pt/Ti/$SiO_2$/Si substrates and post-annealing with the temperature of $550^{\circ}C$~$650^{\circ}C$ for 10 sec~50 sec in a RTA system. The electrical characteristics of the fabricated capacitors showed the highest dielectric constant and remanent polarization[${\varepsilon_r(1kHz)$=690, $2P_r$(-5V~5V sweep)=22$\mu$C/$ \textrm{cm}^2$] in the samples annealed at $650^{\circ}C$ for 30 sec, while the lowest tangent loss and leakage current [$tan\delta(\ge10kHz)\le0.02, \; J_i(5V)=3\mu\textrm{A}/\textrm{cm}^2$]in the samples annealed at $600^{\circ}C$ for 30 sec.

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.392-399
• /
• 1997

In this study, the effect of the sintering temperature on the dielectric and piezoelectric properties of 0.5 wt% $MnO_{2}$-doped $0.125Pb(Mg_{1/2}Nb_{2/3})O_{3}-0.435PbTiO_{3}-0.44PbZrO_{3}$ ceramics were investigated aiming at ultrasonic motor applications. From experimental result, it was found that the optimal sintering temperature condition was at $1270^{\circ}C$. The sample sintered at $1270^{\circ}C$ had density of $7.72\;g/cm^{3}$, dielectric constant of 570, dielectric loss of 0.82%, remanent polarization of $19.18{\mu}C/cm^{2}$, coercive field of 9.63 kV/cm, electromechanical coupling factor of radial mode of 55.1%, mechanical quality factor of 886. Temperature and frequency dependence of dielectric constant and dielectric loss of the sintered sample at $1270^{\circ}C$ was also investigated.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.170-175
• /
• 2004

The ferroelectric (Y $b_{x}$ $Y_{1-x}$)Mn $O_3$ thin films were fabricated by sol-gel method using Y-acetate, Yb-acetate, and Mn-acetate as raw materials. The stable (Y $b_{x}$ $Y_{1-x}$)Mn $O_3$ precursor solution (sol) was prepared through the reflux process with acetylaceton as a catalyst and coated on Si(100) substrate by spin coating. The heat treatment temperature and, Rw ($H_2O$/alkoxide moi ratio) dependence on crystallinity of thin films were studied. The lowest temperature for obtaining YbMn $O_3$phase and the optimum heat-treatment conditions were proved as at 7$50^{\circ}C$ and 80$0^{\circ}C$, respectively. The hexagonal YbMn $O_3$with c-axis preferred orientation could be obtained at Rw=1 condition. The remanent polarization for the thin films of x=0 or 1 was about 200 nC/㎤ while, for the specimens ot 0< x< 1, were 50∼100 nC/$\textrm{cm}^2$.